Kazutada Ikenaga
Research Subjects
Kazutada Ikenaga has a total of 28 co-authors. Here are the top co-authors by number of shared publications:
- Yoshinao Kumagai
Tokyo University of Agriculture and Technology
5 shared publications - Ken Goto
Department of Applied Chemistry, Tokyo University of Agriculture and Technology, Koganei, Tokyo 184-8588, Japan
4 shared publications Shogo Sasaki
Faculty Division of Natural Sciences, Nara Women’s University, Nara, Nara 630-8506, Japan
4 shared publicationsTakahito Okuyama
Department of Applied Chemistry, Tokyo University of Agriculture and Technology, Koganei, Tokyo 184-8588, Japan
4 shared publicationsHaruka Tozato
Department of Applied Chemistry, Tokyo University of Agriculture and Technology, Koganei, Tokyo 184-8588, Japan
3 shared publicationsHideaki Machida
Gas-Phase Growth Ltd. 2 , Koganei, Tokyo 184-0011, Japan
3 shared publications
Latest Publications
- Open Access
- 1 May 2025
- Published by IOP Publishing in Applied Physics Express
- Vol. 18 (5) , 055503
Homoepitaxial growth of thick Si-doped β-Ga2O3 layers using tetramethylsilane as a dopant source by low-pressure hot-wall metalorganic vapor phase epitaxy
By using tetramethylsilane (TMSi) as a Si dopant source, thick intentionally Si-doped β-Ga2O3 homoepitaxial layers were grown by low-pressure hot-wall metalorganic vapor phase epitaxy. The Si concentration was linearly controlled by varying the TMSi supply, and a RT electron density nearly equal to the Si concentration was achieved in the range from 1.8 × 1016 to 1.3 × 1019 cm–3. For the layer with a Si concentration and RT electron density of 1.8 × 1016 cm–3, the RT electron mobility of 136 cm2 V–1 s–1 was found to be limited by polar optical phonon scattering.
- 1 May 2025
- Published by IOP Publishing in Applied Physics Express
- Vol. 18 (5) , 055503
Open AccessHomoepitaxial growth of thick Si-doped β-Ga2O3 layers using tetramethylsilane as a dopant source by low-pressure hot-wall metalorganic vapor phase epitaxy
By using tetramethylsilane (TMSi) as a Si dopant source, thick intentionally Si-doped β-Ga2O3 homoepitaxial layers were grown by low-pressure hot-wall metalorganic vapor phase epitaxy. The Si concentration was linearly controlled by varying the TMSi supply, and a RT electron density nearly equal to the Si concentration was achieved in the range from 1.8 × 1016 to 1.3 × 1019 cm–3. For the layer with a Si concentration and RT electron density of 1.8 × 1016 cm–3, the RT electron mobility of 136 cm2 V–1 s–1 was found to be limited by polar optical phonon scattering.
- Open Access
- 1 September 2023
- Published by IOP Publishing in Applied Physics Express
- Vol. 16 (9) , 095504
High-speed growth of thick high-purity β-Ga2O3 layers by low-pressure hot-wall metalorganic vapor phase epitaxy
High-speed growth of thick, high-purity β-Ga2O3 homoepitaxial layers on (010) β-Ga2O3 substrates by low-pressure hot-wall metalorganic vapor phase epitaxy was investigated using trimethylgallium (TMGa) as the Ga precursor. When the reactor pressure was 2.4–3.4 kPa, the growth temperature was 1000 °C, and a high input VI/III (O/Ga) ratio was used, the growth rate of β-Ga2O3 could be increased linearly by increasing the TMGa supply rate. A thick layer was grown at a growth rate of 16.2 μm h−1 without twinning. Incorporated impurities were not detected, irrespective of the growth rate, demonstrating the promising nature of β-Ga2O3 growth using TMGa.
- 1 September 2023
- Published by IOP Publishing in Applied Physics Express
- Vol. 16 (9) , 095504
Open AccessHigh-speed growth of thick high-purity β-Ga2O3 layers by low-pressure hot-wall metalorganic vapor phase epitaxy
High-speed growth of thick, high-purity β-Ga2O3 homoepitaxial layers on (010) β-Ga2O3 substrates by low-pressure hot-wall metalorganic vapor phase epitaxy was investigated using trimethylgallium (TMGa) as the Ga precursor. When the reactor pressure was 2.4–3.4 kPa, the growth temperature was 1000 °C, and a high input VI/III (O/Ga) ratio was used, the growth rate of β-Ga2O3 could be increased linearly by increasing the TMGa supply rate. A thick layer was grown at a growth rate of 16.2 μm h−1 without twinning. Incorporated impurities were not detected, irrespective of the growth rate, demonstrating the promising nature of β-Ga2O3 growth using TMGa.
- Open Access
- 1 June 2023
- Published by American Vacuum Society in Journal of Vacuum Science & Technology A
- Vol. 41 (4)
Comparison of triethylgallium and diethylgallium ethoxide for β-Ga2O3 growth by metalorganic vapor phase epitaxy
The suitability of diethylgallium ethoxide (Et2GaOEt) containing Ga–O bonds as a Ga precursor for beta-gallium oxide (β-Ga2O3) growth by metalorganic vapor phase epitaxy (MOVPE) was investigated. Because estimating the growth behavior by thermodynamic analysis is difficult as a result of a lack of knowledge about the thermodynamics of Et2GaOEt, the growth behavior was estimated by observing its pyrolysis and combustion processes. Mass spectrometric analysis of gases sampled directly from an MOVPE reactor when only Et2GaOEt was supplied revealed that Et2GaOEt was decomposed to gallane, ethylene, and acetaldehyde by β-hydrogen (β-H) elimination at temperatures greater than 450 °C. However, when Et2GaOEt was supplied together with O2 to the MOVPE reactor maintained at 1000 °C, the combustion of hydrogen and carbon derived from Et2GaOEt was accelerated as the O2 supply was increased. In addition, the amount of O2 required for the complete combustion of Et2GaOEt (i.e., the amount required for the growth of β-Ga2O3) was clarified. On the basis of this pyrolysis/combustion behavior, homoepitaxial growth of β-Ga2O3 layers on β-Ga2O3 substrates was investigated at 1000 °C using Et2GaOEt as a Ga precursor and the growth behavior was compared with that when triethylgallium (Et3Ga) was used as a Ga precursor. Because both Ga precursors ultimately provide Ga gas after β-H elimination, no substantial difference in the growth rate was observed with respect to the amount of Ga atoms injected into the growth reactor. In addition, no substantial difference in crystallinity was observed; homoepitaxial layers grown at 0.7—0.8 μm/h were single crystals without twins, whereas those at 1.5—1.6 μm/h had twins. Et2GaOEt was found to be suitable as a Ga precursor for MOVPE of β-Ga2O3, with performance comparable to that of Et3Ga.
- 1 June 2023
- Published by American Vacuum Society in Journal of Vacuum Science & Technology A
- Vol. 41 (4)
Open AccessComparison of triethylgallium and diethylgallium ethoxide for β-Ga2O3 growth by metalorganic vapor phase epitaxy
The suitability of diethylgallium ethoxide (Et2GaOEt) containing Ga–O bonds as a Ga precursor for beta-gallium oxide (β-Ga2O3) growth by metalorganic vapor phase epitaxy (MOVPE) was investigated. Because estimating the growth behavior by thermodynamic analysis is difficult as a result of a lack of knowledge about the thermodynamics of Et2GaOEt, the growth behavior was estimated by observing its pyrolysis and combustion processes. Mass spectrometric analysis of gases sampled directly from an MOVPE reactor when only Et2GaOEt was supplied revealed that Et2GaOEt was decomposed to gallane, ethylene, and acetaldehyde by β-hydrogen (β-H) elimination at temperatures greater than 450 °C. However, when Et2GaOEt was supplied together with O2 to the MOVPE reactor maintained at 1000 °C, the combustion of hydrogen and carbon derived from Et2GaOEt was accelerated as the O2 supply was increased. In addition, the amount of O2 required for the complete combustion of Et2GaOEt (i.e., the amount required for the growth of β-Ga2O3) was clarified. On the basis of this pyrolysis/combustion behavior, homoepitaxial growth of β-Ga2O3 layers on β-Ga2O3 substrates was investigated at 1000 °C using Et2GaOEt as a Ga precursor and the growth behavior was compared with that when triethylgallium (Et3Ga) was used as a Ga precursor. Because both Ga precursors ultimately provide Ga gas after β-H elimination, no substantial difference in the growth rate was observed with respect to the amount of Ga atoms injected into the growth reactor. In addition, no substantial difference in crystallinity was observed; homoepitaxial layers grown at 0.7—0.8 μm/h were single crystals without twins, whereas those at 1.5—1.6 μm/h had twins. Et2GaOEt was found to be suitable as a Ga precursor for MOVPE of β-Ga2O3, with performance comparable to that of Et3Ga.
- Open Access
- 22 May 2023
- Published by AIP Publishing in Applied Physics Letters
- Vol. 122 (21)
Ion-implanted triple-zone graded junction termination extension for vertical GaN p-n diodes
We demonstrate an ion-implanted triple-zone junction termination extension (JTE) for vertical GaN p-n diodes. Due to the spatial distribution of fixed charge in the triple-zone JTE structure, the peak electric fields at the contact metal edge and at the edge of the JTE are significantly reduced compared to conventional approaches. The forward and reverse characteristics of diodes with conventional single-zone JTE and the triple-zone JTE explored here have been studied and compared experimentally. GaN p-n diodes fabricated using the triple-zone JTE obtain an experimentally measured maximum breakdown voltage of 1.27 kV, appreciably higher than the 1.01 kV achieved using the single-zone JTE structure. The triple-zone JTE design also provides a wider window for fabrication processing and epitaxial wafer growth to achieve the high breakdown voltage compared to single-zone designs. The triple-zone JTE is promising for cost-effective fabrication of GaN power electronics.
- 22 May 2023
- Published by AIP Publishing in Applied Physics Letters
- Vol. 122 (21)
Open AccessIon-implanted triple-zone graded junction termination extension for vertical GaN p-n diodes
We demonstrate an ion-implanted triple-zone junction termination extension (JTE) for vertical GaN p-n diodes. Due to the spatial distribution of fixed charge in the triple-zone JTE structure, the peak electric fields at the contact metal edge and at the edge of the JTE are significantly reduced compared to conventional approaches. The forward and reverse characteristics of diodes with conventional single-zone JTE and the triple-zone JTE explored here have been studied and compared experimentally. GaN p-n diodes fabricated using the triple-zone JTE obtain an experimentally measured maximum breakdown voltage of 1.27 kV, appreciably higher than the 1.01 kV achieved using the single-zone JTE structure. The triple-zone JTE design also provides a wider window for fabrication processing and epitaxial wafer growth to achieve the high breakdown voltage compared to single-zone designs. The triple-zone JTE is promising for cost-effective fabrication of GaN power electronics.
- Open Access
- 12 April 2023
- Published by IOP Publishing in Japanese Journal of Applied Physics
- Vol. 62 (SF) , SF1019
Mass spectrometric study of β-Ga2O3 growth process by metalorganic vapor phase epitaxy
In metalorganic vapor phase epitaxy of β-Ga2O3 using triethylgallium (TEGa) and O2 as precursors and Ar as the carrier gas, the gases directly above the substrate were sampled and analyzed by time-of-flight mass spectrometry. TEGa was found to decompose at 400 °C–600 °C via β-hydrogen elimination reaction to generate gaseous Ga, hydrocarbons (C2H4, C2H2, C2H6), and H2. When β-Ga2O3 was grown at temperatures greater than 1000 °C and with input VI/III ratios greater than 100, the hydrocarbons and H2 were combusted and CO2 and H2O were generated. The C and H impurity concentrations measured by secondary-ion mass spectrometry in the β-Ga2O3(010) homoepitaxial layer grown under these conditions were less than their respective background levels. Thus, to grow β-Ga2O3 without C and H contamination, conditions that favor the complete combustion of hydrocarbons and H2 generated by the decomposition of TEGa should be used.
- 12 April 2023
- Published by IOP Publishing in Japanese Journal of Applied Physics
- Vol. 62 (SF) , SF1019
Open AccessMass spectrometric study of β-Ga2O3 growth process by metalorganic vapor phase epitaxy
In metalorganic vapor phase epitaxy of β-Ga2O3 using triethylgallium (TEGa) and O2 as precursors and Ar as the carrier gas, the gases directly above the substrate were sampled and analyzed by time-of-flight mass spectrometry. TEGa was found to decompose at 400 °C–600 °C via β-hydrogen elimination reaction to generate gaseous Ga, hydrocarbons (C2H4, C2H2, C2H6), and H2. When β-Ga2O3 was grown at temperatures greater than 1000 °C and with input VI/III ratios greater than 100, the hydrocarbons and H2 were combusted and CO2 and H2O were generated. The C and H impurity concentrations measured by secondary-ion mass spectrometry in the β-Ga2O3(010) homoepitaxial layer grown under these conditions were less than their respective background levels. Thus, to grow β-Ga2O3 without C and H contamination, conditions that favor the complete combustion of hydrocarbons and H2 generated by the decomposition of TEGa should be used.
- Open Access
- 29 March 2021
- Published by IOP Publishing in Japanese Journal of Applied Physics
- Vol. 60 (4) , 045505
Thermodynamic and experimental studies of β-Ga2O3 growth by metalorganic vapor phase epitaxy
Thermodynamic analysis and experimental demonstration of β-Ga2O3 growth by metalorganic vapor phase epitaxy using triethylgallium (TEG) and oxygen (O2) precursors were performed. Thermodynamic analysis revealed that the O2 supplied is preferentially used for the combustion of hydrocarbons and H2 derived from TEG. Therefore, the use of high growth temperatures and high input VI/III ratios is essential for the complete combustion of hydrocarbons and H2, and β-Ga2O3 growth. The use of an inert gas as the carrier gas was also determined as necessary to grow β-Ga2O3 at high temperatures. Based on these results, a ( 2 ¯ 01) oriented smooth β-Ga2O3 layer could be grown on a c-plane sapphire substrate at 900 °C with a growth rate of 1.4 μm h−1 at an input VI/III ratio of 100. The grown layer showed a clear optical bandgap of 4.84 eV, and impurity concentrations of hydrogen and carbon were below the background levels of the measurement system.
- 29 March 2021
- Published by IOP Publishing in Japanese Journal of Applied Physics
- Vol. 60 (4) , 045505
Open AccessThermodynamic and experimental studies of β-Ga2O3 growth by metalorganic vapor phase epitaxy
Thermodynamic analysis and experimental demonstration of β-Ga2O3 growth by metalorganic vapor phase epitaxy using triethylgallium (TEG) and oxygen (O2) precursors were performed. Thermodynamic analysis revealed that the O2 supplied is preferentially used for the combustion of hydrocarbons and H2 derived from TEG. Therefore, the use of high growth temperatures and high input VI/III ratios is essential for the complete combustion of hydrocarbons and H2, and β-Ga2O3 growth. The use of an inert gas as the carrier gas was also determined as necessary to grow β-Ga2O3 at high temperatures. Based on these results, a ( 2 ¯ 01) oriented smooth β-Ga2O3 layer could be grown on a c-plane sapphire substrate at 900 °C with a growth rate of 1.4 μm h−1 at an input VI/III ratio of 100. The grown layer showed a clear optical bandgap of 4.84 eV, and impurity concentrations of hydrogen and carbon were below the background levels of the measurement system.