GLGraham Leggett

Graham Leggett

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Graham Leggett has a total of 11 co-authors. Here are the top co-authors by number of shared publications:

  • Angus Shiue

    Department of Molecular Science and Engineering, Research and Development Center for Smart Textile Technology, National Taipei University of Technology, Taipei 106, Taiwan

    3 shared publications
  • Kai-Yen Chin

    Department of Molecular Science and Engineering, National Taipei University of Technology, Taipei 106, Taiwan

    3 shared publications
  • Shu-Mei Chang

    Department of Molecular Science and Engineering, National Taipei University of Technology, Taipei 106, Taiwan

    3 shared publications
  • Yeou-Fong Li

    Department of Civil Engineering, National Taipei University of Technology, Taipei 10608, Taiwan

    2 shared publications
  • Yi-Jing Wu

    Department of Molecular Science and Engineering, Research and Development Center for Smart Textile Technology, National Taipei University of Technology, Taipei 106, Taiwan

    2 shared publications
  • Chao-Heng Tseng

    Institute of Environment Engineering and Management, National Taipei University of Technology, 1, Sec. 3, Zhongxiao E. Rd., Taipei 10608, Taiwan

    1 shared publication

Latest Publications

  • Open Access

    Comparative Study of Continuous-Flow Reactors for Emulsion Polymerization

    by Kai-Yen Chin, Angus Shiue, Pei-Yu Lai, Chien-Chen Chu, Shu-Mei Chang, Graham Leggett

    Polymer fouling in batch and tubular reactors creates safety hazards from heat buildup and blockages. The continuous Corning Advanced-Flow™ Reactor (AFR) offers enhanced mass and heat transfer, improving safety and efficiency. This study evaluated three reactor systems—a monolithic AFR, an AFR with an external pipe, and a conventional tubular reactor—for the mini-emulsion polymerization of styrene and subsequent styrene–acrylic acid copolymerization. The AFR operability under varying monomer concentrations was assessed and investigated, with the residence time’s effects on conversion. For styrene polymerization at 20–35 wt% monomer, the highest conversions achieved were 88.0% in the AFR, 85.8% in the tubular reactor, and 98.9% in the AFR with pipe. Uniform particles were obtained at ≤30 wt%, whereas at 35 wt%, the monolithic AFR experienced clogging and loss of particle uniformity. Similarly, in styrene–acrylic acid copolymerization (15–17.5 wt% monomer), the maximum conversions reached 80.1% in the AFR and 95.4% in the AFR with pipe, while the monolithic AFR again experienced blockage at 17.5 wt%. In conclusion, integrating an external pipe with the AFR, coupled with higher flow rates, significantly improved initiator diffusion, enhanced monomer conversion, and mitigated blockage. This approach enabled the efficient, continuous production of nanoscale, uniformly sized polystyrene and styrene–acrylic acid copolymers even at high monomer concentrations.


  • Open Access

    Carbon Fiber Recycling from Waste CFRPs via Microwave Pyrolysis: Gas Emissions Monitoring and Mechanical Properties of Recovered Carbon Fiber

    by Kai-Yen Chin, Angus Shiue, Jhu-Lin You, Yi-Jing Wu, Kai-Yi Cheng, Shu-Mei Chang, Yeou-Fong Li, Chao-Heng Tseng, Graham Leggett

    Disposing of carbon fiber-reinforced polymers (CFRPs) has become a pressing issue due to their increasing application across various industries. Previous work has focused on removing silane coupling agent residues on recovered carbon fibers via microwave pyrolysis, making them suitable for use in new materials. However, the mechanical performance and structural characteristics of these fibers have not been fully reported. This study investigates the time–temperature curves of CFRPs treated through microwave pyrolysis and analyzes the mechanical and structural properties of silane-controllable recovered carbon fibers. Additionally, emissions—including carbon monoxide, carbon dioxide, and particulate aerosols—were measured using handheld monitors and thermal desorption–gas chromatography/mass spectrometry to determine the composition of fugitive gases around the microwave pyrolysis system. The pyrolysis process at 950 °C, with an additional 1 h holding time, reduced the crystallite size from 0.297 Å to 0.222 Å, significantly enhancing tensile strength (3804 ± 713 MPa) and tensile modulus (200 ± 13 GPa). This study contributes to more sustainable CFRP waste treatment and highlights the potential for reusing high-quality carbon fibers in new applications, enhancing both environmental and worker safety.


  • Open Access

    Studies on Recycling Silane Controllable Recovered Carbon Fiber from Waste CFRP

    by Kai-Yen Chin, Angus Shiue, Yi-Jing Wu, Shu-Mei Chang, Yeou-Fong Li, Ming-Yuan Shen, Graham Leggett

    During the production process of commercial carbon fiber reinforced polymers (CFRPs), a silane coupling agent is added to the carbon fiber at the sizing step as a binder to enhance the product’s physical properties. While improving strength, the silane coupling agent results in a silane residue on recovered carbon fibers (rCF) after recycling, which is a disadvantage when using recovered carbon fibers in the manufacture of new materials. In this study, the rCF is recovered from waste carbon fiber reinforced polymers (CFRPs) from the bicycle industry by a microwave pyrolysis method, applying a short reaction time and in an air atmosphere. Moreover, the rCF are investigated for their surface morphologies and the elements present on the surface. The silicon element content changes with pyrolysis temperature were 0.4, 0.9, and 0.2%, respectively, at 450, 550, and 650 °C. Additionally, at 950 °C, silicon content can be reduced to 0.1 ± 0.05%. The uniformity of microwave pyrolysis recycle treatment was compared with traditional furnace techniques used for bulk waste treatment by applying the same temperature regime. This work provides evidence that microwave pyrolysis can be used as an alternative method for the production of rCFs for reuse applications.