Olawale Saheed Ismail
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Olawale Saheed Ismail has a total of 11 co-authors. Here are the top co-authors by number of shared publications:
- Olanrewaju Miracle Oyewola
Department of Mechanical Engineering, University of Alaska Fairbanks, Alaska, USA
2 shared publications A. S. Shote
Olabisi Onabanjo University
1 shared publication- Ademola Dare
University of Ibadan, Ibadan, Nigeria
1 shared publication - Adetokunbo A. Awonusi
Department of Mechanical Engineering, University of Ibadan, Ibadan, Oyo State, Nigeria
1 shared publication - Lateef Anjola Sanni
University of Ibadan
1 shared publication M. A. Sulaiman
Olabisi Onabanjo University
1 shared publication
Latest Publications
- Open Access
- 6 April 2023
- Published by Elsevier in Alexandria Engineering Journal
- Vol. 71, 631-644
Design optimization of Air-Cooled Li-ion battery thermal management system with Step-like divergence plenum for electric vehicles
- 6 April 2023
- Published by Elsevier in Alexandria Engineering Journal
- Vol. 71, 631-644
Open AccessDesign optimization of Air-Cooled Li-ion battery thermal management system with Step-like divergence plenum for electric vehicles
- Open Access
- 10 January 2022
- Published by OU Scientific Route in EUREKA: Physics and Engineering
- No. 1,p. 3-11
Numerical simulation of reynolds number effect of a free incompressible isothermal turbulent coaxial jet
This paper studies the effect of Reynolds number on a two-dimensional free incompressible isothermal coaxial turbulent jet over a range of high Reynolds numbers. This is necessary because of its application in noise control and mixing. The Reynolds numbers at the nozzle exit were 9824, 19648, 29472, 39296 and 49120. The models were designed in ANSYS Design Modeler and the numerical simulation was done using a finite volume based Computational Fluid Dynamics (CFD) in ANSYS FLUENT using the two-dimensional Realizable turbulence model. The Governing equations were discretized using the finite volume method with the solution based on the PISO algorithm. The decay of centerline velocity, turbulent kinetic energy profile, the radial profile of axial velocity and similarity profile were investigated along the flow direction. Contour plot indicates that the velocity is high at the jet exit and decreases downstream due to the rapid mixing of the inner and outer jet and the surrounding fluid. It is found generally that Reynolds number plays significant role especially before self-similarity region. The result shows that increasing the Reynolds number give rise to more turbulence which in turn decreases the potential core length, turbulent kinetic energy and enhances the mixing of the fluid. However, at the jet exit, the flow with the lowest Reynolds number has the highest turbulent kinetic energy because it suffers the greater shear. The spreading of the jet was more or less independent of the Reynolds number beyond the self-similarity region. It is also found that the velocity profile is brought to congruence at about z/D=25 for the Reynolds numbers considered
- 10 January 2022
- Published by OU Scientific Route in EUREKA: Physics and Engineering
- No. 1,p. 3-11
Open AccessNumerical simulation of reynolds number effect of a free incompressible isothermal turbulent coaxial jet
This paper studies the effect of Reynolds number on a two-dimensional free incompressible isothermal coaxial turbulent jet over a range of high Reynolds numbers. This is necessary because of its application in noise control and mixing. The Reynolds numbers at the nozzle exit were 9824, 19648, 29472, 39296 and 49120. The models were designed in ANSYS Design Modeler and the numerical simulation was done using a finite volume based Computational Fluid Dynamics (CFD) in ANSYS FLUENT using the two-dimensional Realizable turbulence model. The Governing equations were discretized using the finite volume method with the solution based on the PISO algorithm. The decay of centerline velocity, turbulent kinetic energy profile, the radial profile of axial velocity and similarity profile were investigated along the flow direction. Contour plot indicates that the velocity is high at the jet exit and decreases downstream due to the rapid mixing of the inner and outer jet and the surrounding fluid. It is found generally that Reynolds number plays significant role especially before self-similarity region. The result shows that increasing the Reynolds number give rise to more turbulence which in turn decreases the potential core length, turbulent kinetic energy and enhances the mixing of the fluid. However, at the jet exit, the flow with the lowest Reynolds number has the highest turbulent kinetic energy because it suffers the greater shear. The spreading of the jet was more or less independent of the Reynolds number beyond the self-similarity region. It is also found that the velocity profile is brought to congruence at about z/D=25 for the Reynolds numbers considered
- Open Access
- 1 July 2021
- Published by IIUM Press in IIUM Engineering Journal
- Vol. 22 (2) , 339-351
INVESTIGATION OF MULTI-ZONE MODELS FOR SPARK IGNITION ENGINE FUELED WITH ETHANOL
This research is aimed at investigating the effect of using ethanol (E100) in multi-zone model analysis consisting of multi-combustion chamber zoning cases. The first case considered is a three-zone model that has an unburned zone, burned zone, and transitory zone. The second case model is also three-zone, consisting of an unburned zone and two partitioned burned zones. The burned zone was imagined partitioned into burned zone-1 and burned zone-2 under uneven fuel distribution having different equivalent ratios. The third case is a four-zone model including two regions of burned zone, an unburned zone and a transitory zone, which is unburned burned zone containing a mixture of unburned and burned gases. Arbitrary constants for each of the unburned (CC1) and burned (CC2) Zone leakages in the unburned burned Zone are 0.00025, 0.0005, 0.001, 0.002, 0.005, 0.1 and 0.5. The Mass Fraction Burned (MFB) for zone-1, x1 and burned zone-2, x2 are computed using Partitioned Burnt Zones Ratios (PBZR) of 2:8, 3:7, 4:6, 5:5, 6:4, 7:3 and 8:2. Two equivalent ratios, one for each fuel MFB (phi 1, phi 2), (0.8, 0.6) and (0.6, 0.8) are analyzed using fuel blends of varying percentage. A comparison of values of the three zoning cases is done using peak values from the three-zone models to evaluate the four-zone model. The model was compared with a spark ignition engine (SIE) operating with a premium motor spirit (PMS) serving as baseline. The engine operating conditions were set at an engine speed of 2000 rpm, -35bTDC ignition time, and burn duration at 60 degrees C. The indicated mean effective pressure (IMEP), thermal efficiency (eta), cylinder pressure and emission fraction from the developed models and those of two-zone analysis obtained agreed with literature values. The result showed it is undesirable to have a high volume of burned charge as infiltrate. The three-zone segmented model predicted the highest engine thermal efficiency and peak pressure at mass burn ratio of 7:3. A general reduction in N-2 emission was observed for the three-zone transitional and four-zone models.
- 1 July 2021
- Published by IIUM Press in IIUM Engineering Journal
- Vol. 22 (2) , 339-351
Open AccessINVESTIGATION OF MULTI-ZONE MODELS FOR SPARK IGNITION ENGINE FUELED WITH ETHANOL
This research is aimed at investigating the effect of using ethanol (E100) in multi-zone model analysis consisting of multi-combustion chamber zoning cases. The first case considered is a three-zone model that has an unburned zone, burned zone, and transitory zone. The second case model is also three-zone, consisting of an unburned zone and two partitioned burned zones. The burned zone was imagined partitioned into burned zone-1 and burned zone-2 under uneven fuel distribution having different equivalent ratios. The third case is a four-zone model including two regions of burned zone, an unburned zone and a transitory zone, which is unburned burned zone containing a mixture of unburned and burned gases. Arbitrary constants for each of the unburned (CC1) and burned (CC2) Zone leakages in the unburned burned Zone are 0.00025, 0.0005, 0.001, 0.002, 0.005, 0.1 and 0.5. The Mass Fraction Burned (MFB) for zone-1, x1 and burned zone-2, x2 are computed using Partitioned Burnt Zones Ratios (PBZR) of 2:8, 3:7, 4:6, 5:5, 6:4, 7:3 and 8:2. Two equivalent ratios, one for each fuel MFB (phi 1, phi 2), (0.8, 0.6) and (0.6, 0.8) are analyzed using fuel blends of varying percentage. A comparison of values of the three zoning cases is done using peak values from the three-zone models to evaluate the four-zone model. The model was compared with a spark ignition engine (SIE) operating with a premium motor spirit (PMS) serving as baseline. The engine operating conditions were set at an engine speed of 2000 rpm, -35bTDC ignition time, and burn duration at 60 degrees C. The indicated mean effective pressure (IMEP), thermal efficiency (eta), cylinder pressure and emission fraction from the developed models and those of two-zone analysis obtained agreed with literature values. The result showed it is undesirable to have a high volume of burned charge as infiltrate. The three-zone segmented model predicted the highest engine thermal efficiency and peak pressure at mass burn ratio of 7:3. A general reduction in N-2 emission was observed for the three-zone transitional and four-zone models.