Selvaraj Praburanganathan
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Selvaraj Praburanganathan has a total of 12 co-authors. Here are the top co-authors by number of shared publications:
- Sudharsan Narayanasamy
Vidya Jyothi Institute of Technology, India
2 shared publications - Lakshmaiya Natrayan
Department of Mechanical Engineering, Saveetha School of Engineering, SIMATS, Chennai, India
1 shared publication N. Sudharsan
Department of Civil Engineering, Vidya Jyothi Institute of Technology, Hyderabad, India
1 shared publication- Naga Dheeraj Kumar Reddy Chukka
Department of Civil Engineering, Aditya University
1 shared publication - Pavan Kumar P
Department of Civil Engineering, Vidya Jyothi Institute of Technology, Hyderabad, India
1 shared publication - Prabhu Paramasivam
Department of Research and Innovation, Saveetha School of Engineering, SIMATS, Chennai, India
1 shared publication
Latest Publications
- Open Access
- 1 January 2025
- Published by FapUNIFESP (SciELO) in Matéria (Rio de Janeiro)
- Vol. 30
Sustainable basalt fibre reinforced alkali-activated geopolymer concrete for sustainable environments
A novel study on fibre-reinforced cement less geopolymer concrete with diverse molar concentrations has gained attention in recent years. The current study uniquely explores the combined influence of four distinct molar concentrations (6M, 8M, 10M, and 12M) and five fibre volume fractions (0%, 0.25%, 0.50%, 0.75%, and 1%) on the mechanical behaviour of GPC. An experimental investigation on 20 numbers of varied geopolymer concrete mixes was performed, and the mechanical properties were evaluated and reported. Also, A non-destructive test using ultrasonic pulse velocity was made, and the regression analysis with compressive strength is reported. The result indicates that 10M concentration provides the optimum results than other molar concentrations, with 0.75% as the optimum basalt fibre volume addition to the cementless geopolymer concrete. The basalt fibre addition improves the split tensile strength and flexural bending strengths considerably. Morphology studies indicate that the lower molar concentration gives a comparatively loose and voided concrete matrix with a loose packing of ingredients than the higher molar concentration. This research provides a comprehensive and optimised approach by simultaneous variation of Molar concentration and fibre volume to enhance geopolymer concrete, supported by both mechanical investigation and microstructural analysis.
- 1 January 2025
- Published by FapUNIFESP (SciELO) in Matéria (Rio de Janeiro)
- Vol. 30
Open AccessSustainable basalt fibre reinforced alkali-activated geopolymer concrete for sustainable environments
A novel study on fibre-reinforced cement less geopolymer concrete with diverse molar concentrations has gained attention in recent years. The current study uniquely explores the combined influence of four distinct molar concentrations (6M, 8M, 10M, and 12M) and five fibre volume fractions (0%, 0.25%, 0.50%, 0.75%, and 1%) on the mechanical behaviour of GPC. An experimental investigation on 20 numbers of varied geopolymer concrete mixes was performed, and the mechanical properties were evaluated and reported. Also, A non-destructive test using ultrasonic pulse velocity was made, and the regression analysis with compressive strength is reported. The result indicates that 10M concentration provides the optimum results than other molar concentrations, with 0.75% as the optimum basalt fibre volume addition to the cementless geopolymer concrete. The basalt fibre addition improves the split tensile strength and flexural bending strengths considerably. Morphology studies indicate that the lower molar concentration gives a comparatively loose and voided concrete matrix with a loose packing of ingredients than the higher molar concentration. This research provides a comprehensive and optimised approach by simultaneous variation of Molar concentration and fibre volume to enhance geopolymer concrete, supported by both mechanical investigation and microstructural analysis.
- 3 June 2022
- Published by Taylor & Francis in International Journal of Coal Preparation and Utilization
- Vol. 43 (6) , 971-986
Interaction of anthracite coal ash and Archis hypogaea shell ash on an innovative brick: an experimental and simulation study
The research recommends a novel and sustainable method to utilize an agricultural waste in the anthracite coal ash-based brick production. Arachis hypogaea shell ash is used as a substitute for the sand in the anthracite ash-based brick production. Also, random forests are used for the strength prediction. The tests for compressive strength, water absorption, efflorescence and hardness are being conducted to assess the performance. The presence of shell ash up to 60% replacement resulted in an incremental trend of anthracite ash-based brick’s strength with a denser microstructure. The M-sand to Arachis hypogaea shell ash ratio has to be maintained at 40:60 to get the optimum results. The addition of shell ash to the Anthracite coal ash brick could reduce the absorption rates by nearly 37%. The correlogram and relatively variable importance suggests that the curing regime plays a dominant role than the shell ash content. Random forests predicted the strength accurately with least errors. A novel mathematical equation is being proposed to predict the compressive strength of the Innovative brick. The research could significantly contribute to the sustainable utilization of the Arachis hypogaea shell ash in the brick production and it leads lesser utilization of manufactured sand.
- 3 June 2022
- Published by Taylor & Francis in International Journal of Coal Preparation and Utilization
- Vol. 43 (6) , 971-986
Interaction of anthracite coal ash and Archis hypogaea shell ash on an innovative brick: an experimental and simulation study
The research recommends a novel and sustainable method to utilize an agricultural waste in the anthracite coal ash-based brick production. Arachis hypogaea shell ash is used as a substitute for the sand in the anthracite ash-based brick production. Also, random forests are used for the strength prediction. The tests for compressive strength, water absorption, efflorescence and hardness are being conducted to assess the performance. The presence of shell ash up to 60% replacement resulted in an incremental trend of anthracite ash-based brick’s strength with a denser microstructure. The M-sand to Arachis hypogaea shell ash ratio has to be maintained at 40:60 to get the optimum results. The addition of shell ash to the Anthracite coal ash brick could reduce the absorption rates by nearly 37%. The correlogram and relatively variable importance suggests that the curing regime plays a dominant role than the shell ash content. Random forests predicted the strength accurately with least errors. A novel mathematical equation is being proposed to predict the compressive strength of the Innovative brick. The research could significantly contribute to the sustainable utilization of the Arachis hypogaea shell ash in the brick production and it leads lesser utilization of manufactured sand.
- 16 March 2022
- Published by Springer Nature in Environmental Science and Pollution Research
- Vol. 29 (36) , 54193-54218
Synergistic effect on the performance of ash-based bricks with glass wastes and granite tailings along with strength prediction by adopting machine learning approach
The study proposes a novel and sustainable method to appropriately utilize wastes from granite as well as glass industries in brick manufacturing. An ecofriendly and low-cost manufacturing process of ash-based bricks pertaining to the Indian standard codal provisions that can be adopted on the commercial scale is deliberated. The research also recommends the method for predicting the strength of the ash-based bricks using machine learning algorithms like random forests and decision trees. For positive synergy in the performance, both the granite tailings and glass waste must be used together. Using the granite tailings and glass waste together led to a significant reduction of 75% in the fly ash requirement without compromising the brick’s performance. The addition of the granite tailings and glass waste in the mix could increase the strength of the brick by 90.5% and 37.7%, respectively. Beyond 30% dosage of granite, tailings are not recommended as they may lead to the poor gradation of particles and weak bonding in the microstructure. The glass waste in the mixture should not be more than 15% as it causes the dilution of pozzolanic reactions thereby forming fewer hydrated compounds. Brick’s durability is known after exposing the specimens for 1 year to sewers and biogenic corrosion environment, marine environment, and saline soil environment, respectively. The inclusion of the industrial wastes significantly reduced the specimen damage in the extreme environmental conditions along with the least absorption rates. The dosage of ash, granite tailings, and glass waste has to be maintained around 15%, 30%, and 15%, respectively for attaining the optimum performance. Out of the generated machine learning algorithms, only random forests could be able to predict the values accurately with R2 values at 0.90 and with comparatively lesser errors.
- 16 March 2022
- Published by Springer Nature in Environmental Science and Pollution Research
- Vol. 29 (36) , 54193-54218
Synergistic effect on the performance of ash-based bricks with glass wastes and granite tailings along with strength prediction by adopting machine learning approach
The study proposes a novel and sustainable method to appropriately utilize wastes from granite as well as glass industries in brick manufacturing. An ecofriendly and low-cost manufacturing process of ash-based bricks pertaining to the Indian standard codal provisions that can be adopted on the commercial scale is deliberated. The research also recommends the method for predicting the strength of the ash-based bricks using machine learning algorithms like random forests and decision trees. For positive synergy in the performance, both the granite tailings and glass waste must be used together. Using the granite tailings and glass waste together led to a significant reduction of 75% in the fly ash requirement without compromising the brick’s performance. The addition of the granite tailings and glass waste in the mix could increase the strength of the brick by 90.5% and 37.7%, respectively. Beyond 30% dosage of granite, tailings are not recommended as they may lead to the poor gradation of particles and weak bonding in the microstructure. The glass waste in the mixture should not be more than 15% as it causes the dilution of pozzolanic reactions thereby forming fewer hydrated compounds. Brick’s durability is known after exposing the specimens for 1 year to sewers and biogenic corrosion environment, marine environment, and saline soil environment, respectively. The inclusion of the industrial wastes significantly reduced the specimen damage in the extreme environmental conditions along with the least absorption rates. The dosage of ash, granite tailings, and glass waste has to be maintained around 15%, 30%, and 15%, respectively for attaining the optimum performance. Out of the generated machine learning algorithms, only random forests could be able to predict the values accurately with R2 values at 0.90 and with comparatively lesser errors.
- Top Cited PapersOpen Access
- 12 January 2022
- Published by Wiley in Advances in Civil Engineering
- Vol. 2022 (1)
Force‐Deformation Study on Glass Fiber Reinforced Concrete Slab Incorporating Waste Paper
This study inspects the viability of engaging the discarded paper wastes in concrete by varying the volume proportions from 0%–20% with each 5% increment in replacement of the weight of cement. A physiomechanical study was conducted, and the results were presented. A glass fiber reinforced rectangular slab with a longer span (ly) to shorter span (lx) ratio of (ly:lx) 1.16 was cast with optimum replacement of waste‐paper mass and compared the force‐deformation characteristics with the conventional concrete slab without waste paper. The optimum percentage of discarded papers for the replacement of cement is 5%. Also, the results imply that the compressive strength at the age of 28 days is 30% improved for the optimum replacement. Based on the outcomes of the investigation, it can be inferred that the compressive strength gets progressively reduced if the volume of the discarded paper gets increases. The incorporation of glass fibers improves the split and flexural strength of the concrete specimens considerably. The ultimate load‐carrying capacity of the glass fiber reinforced waste paper incorporated concrete slab measured 42% lower than that of the conventional slab. However, development of the new type of concrete incorporating waste papers is the new trend in ensuring the sustainability of construction materials.
- 12 January 2022
- Published by Wiley in Advances in Civil Engineering
- Vol. 2022 (1)
Top Cited PapersOpen AccessForce‐Deformation Study on Glass Fiber Reinforced Concrete Slab Incorporating Waste Paper
This study inspects the viability of engaging the discarded paper wastes in concrete by varying the volume proportions from 0%–20% with each 5% increment in replacement of the weight of cement. A physiomechanical study was conducted, and the results were presented. A glass fiber reinforced rectangular slab with a longer span (ly) to shorter span (lx) ratio of (ly:lx) 1.16 was cast with optimum replacement of waste‐paper mass and compared the force‐deformation characteristics with the conventional concrete slab without waste paper. The optimum percentage of discarded papers for the replacement of cement is 5%. Also, the results imply that the compressive strength at the age of 28 days is 30% improved for the optimum replacement. Based on the outcomes of the investigation, it can be inferred that the compressive strength gets progressively reduced if the volume of the discarded paper gets increases. The incorporation of glass fibers improves the split and flexural strength of the concrete specimens considerably. The ultimate load‐carrying capacity of the glass fiber reinforced waste paper incorporated concrete slab measured 42% lower than that of the conventional slab. However, development of the new type of concrete incorporating waste papers is the new trend in ensuring the sustainability of construction materials.