Felipe Rosas-Diaz
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Felipe Rosas-Diaz has a total of 29 co-authors. Here are the top co-authors by number of shared publications:
- Cesar Antonio Juarez Alvarado
Facultad de Ingeniería Civil, Universidad Autónoma de Nuevo León, San Nicolás de los Garza, Mexico
4 shared publications - Carola Alejandra Blazquez
Department of Engineering Sciences, Universidad Andres Bello, Quillota 980, Viña del Mar 2531015, Chile
3 shared publications - Juana Maria Delgado-Saborit
Department of Medicine, Faculty of Health Sciences, Universitat Jaume I, Avenida de Vicent Sos Baynat s/n, 12071, Castellón de la Plana, Spain; Epidemiology and Environmental Health Joint Research Unit, Foundation for the Promotion of Health and Biomedical Research in the Valencian Region, FISABIO-Public Health, FISABIO-Universitat Jaume I-Universitat de València, Av. Catalunya 21, 46020, Valencia, Spain
3 shared publications - María Elisa Quinteros
Departamento de Salud Pública, Facultad de Ciencias de la Salud, Universidad de Talca, Avenida Lircay s/n, Talca, 3460000, Chile
3 shared publications - Pablo Ruiz-Rudolph
Epidemiology Program, Institute of Population Health, Faculty of Medicine, Universidad de Chile , Independencia, Santiago
3 shared publications - Roy Michael Harrison
School of Geography, Earth & Environmental Sciences, University of Birmingham, United Kingdom
3 shared publications
Latest Publications
- 8 April 2025
- Published by Elsevier in Resources, Conservation and Recycling
- Vol. 219
Biomass-based concrete could effectively decarbonize buildings in Mexico
- 8 April 2025
- Published by Elsevier in Resources, Conservation and Recycling
- Vol. 219
Biomass-based concrete could effectively decarbonize buildings in Mexico
- Open Access
- 26 March 2025
- Published by Springer Nature in Discover Civil Engineering
- Vol. 2 (1) , 1-17
Taguchi experimental matrix optimization of two plant-based concretes with sargassum (Sargassum fluitans) and peanut shell (Arachis hypogaea) aggregate
- 26 March 2025
- Published by Springer Nature in Discover Civil Engineering
- Vol. 2 (1) , 1-17
Open AccessTaguchi experimental matrix optimization of two plant-based concretes with sargassum (Sargassum fluitans) and peanut shell (Arachis hypogaea) aggregate
- Open Access
- 27 June 2024
- Published by MDPI AG in Sustainability
- Vol. 16 (13) , 5455
Development of Lignocellulosic-Based Insulation Materials from Agave fourcroydes and Washingtonia filifera for Use in Sustainable Buildings
The objective of this work was to develop two prototypes of insulating materials based on natural plant fibers from Agave fourcroydes and Washingtonia filifera, available in Mexico, for their potential use in buildings. For the development of the prototypes, the raw materials were characterized by physical, chemical, and microstructural methods. The samples were prepared by a pulping process after boiling the fibers in a sodium hydroxide solution. We worked with a Taguchi experimental matrix of four variables in three levels, defining as response variables the sample’s thermal conductivity, density, and flexural strength. The results show that the henequen-based insulation obtained a density of 69.8 kg/m3 and a thermal conductivity of 0.0367 W/mK; on the other hand, the palm-based insulation obtained a density of 45.06 g/cm3 and a thermal conductivity of 0.0409 W/mK, which in both cases are like the conductivity values reported by conventional insulating materials, such as expanded polystyrene or mineral wool, and therefore both optimized prototypes are promising as thermal insulators with a high potential to be used in sustainable buildings in Mexico, reducing the energy consumption of air conditioning and the environmental impact associated with the production of materials.
- 27 June 2024
- Published by MDPI AG in Sustainability
- Vol. 16 (13) , 5455
Open AccessDevelopment of Lignocellulosic-Based Insulation Materials from Agave fourcroydes and Washingtonia filifera for Use in Sustainable Buildings
The objective of this work was to develop two prototypes of insulating materials based on natural plant fibers from Agave fourcroydes and Washingtonia filifera, available in Mexico, for their potential use in buildings. For the development of the prototypes, the raw materials were characterized by physical, chemical, and microstructural methods. The samples were prepared by a pulping process after boiling the fibers in a sodium hydroxide solution. We worked with a Taguchi experimental matrix of four variables in three levels, defining as response variables the sample’s thermal conductivity, density, and flexural strength. The results show that the henequen-based insulation obtained a density of 69.8 kg/m3 and a thermal conductivity of 0.0367 W/mK; on the other hand, the palm-based insulation obtained a density of 45.06 g/cm3 and a thermal conductivity of 0.0409 W/mK, which in both cases are like the conductivity values reported by conventional insulating materials, such as expanded polystyrene or mineral wool, and therefore both optimized prototypes are promising as thermal insulators with a high potential to be used in sustainable buildings in Mexico, reducing the energy consumption of air conditioning and the environmental impact associated with the production of materials.
- 17 November 2023
- Published by American Chemical Society (ACS) in Environmental Science & Technology
- Vol. 57 (48) , 19473-19486
Development of Spatio-Temporal Land Use Regression Models for Fine Particulate Matter and Wood-Burning Tracers in Temuco, Chile
Biomass burning is common in much of the world, and in some areas, residential wood-burning has increased. However, air pollution resulting from biomass burning is an important public health problem. A sampling campaign was carried out between May 2017 and July 2018 in over 64 sites in four sessions, to develop a spatio-temporal land use regression (LUR) model for fine particulate matter (PM) and wood-burning tracers levoglucosan and soluble potassium (Ksol) in a city heavily impacted by wood-burning. The mean (sd) was 46.5 (37.4) μg m-3 for PM2.5, 0.607 (0.538) μg m-3 for levoglucosan, and 0.635 (0.489) μg m-3 for Ksol. LUR models for PM2.5, levoglucosan, and Ksol had a satisfactory performance (LOSOCV R2), explaining 88.8%, 87.4%, and 87.3% of the total variance, respectively. All models included sociodemographic predictors consistent with the pattern of use of wood-burning in homes. The models were applied to predict concentrations surfaces and to estimate exposures for an epidemiological study.
- 17 November 2023
- Published by American Chemical Society (ACS) in Environmental Science & Technology
- Vol. 57 (48) , 19473-19486
Development of Spatio-Temporal Land Use Regression Models for Fine Particulate Matter and Wood-Burning Tracers in Temuco, Chile
Biomass burning is common in much of the world, and in some areas, residential wood-burning has increased. However, air pollution resulting from biomass burning is an important public health problem. A sampling campaign was carried out between May 2017 and July 2018 in over 64 sites in four sessions, to develop a spatio-temporal land use regression (LUR) model for fine particulate matter (PM) and wood-burning tracers levoglucosan and soluble potassium (Ksol) in a city heavily impacted by wood-burning. The mean (sd) was 46.5 (37.4) μg m-3 for PM2.5, 0.607 (0.538) μg m-3 for levoglucosan, and 0.635 (0.489) μg m-3 for Ksol. LUR models for PM2.5, levoglucosan, and Ksol had a satisfactory performance (LOSOCV R2), explaining 88.8%, 87.4%, and 87.3% of the total variance, respectively. All models included sociodemographic predictors consistent with the pattern of use of wood-burning in homes. The models were applied to predict concentrations surfaces and to estimate exposures for an epidemiological study.
- 5 December 2022
- Published by Elsevier in Atmospheric Environment
- Vol. 294, 119529
Spatio-temporal distribution of particulate matter and wood-smoke tracers in Temuco, Chile: A city heavily impacted by residential wood-burning
- 5 December 2022
- Published by Elsevier in Atmospheric Environment
- Vol. 294, 119529
Spatio-temporal distribution of particulate matter and wood-smoke tracers in Temuco, Chile: A city heavily impacted by residential wood-burning
- Open Access
- 3 November 2022
- Published by MDPI AG in Sustainability
- Vol. 14 (21) , 14397
Sustainable Proposal for Plant-Based Cementitious Composites, Evaluation of Their Mechanical, Durability and Comfort Properties
This research evaluates four sustainable cementitious composites with sustainable plant fibers and bio-aggregates: (1) cementitious matrix composite with lechuguilla fibers (LFC) and (2) with flax fibers (FFC); and (3) cementitious matrix composite with wood shavings (WSC) and (4) with hemp shavings (HSC). The fibers are for reinforcement and the shavings act as bio-aggregates as a total replacement for limestone aggregates. The lechuguilla (LF) and flax (FF) fibers were treated; wood (WS) and hemp (HS) bio-aggregates were also processed. Nineteen mixtures were manufactured, and five were used as controls, and the hygrothermal, mechanical, and durability properties were evaluated. The results for LFC and FFC showed that fiber treatment negatively affected flexural–compressive strength; untreated LFC with accelerated deterioration had better mechanical behavior, higher density, and lower porosity than FFC. Strength and density decreased, but porosity increased with increasing fiber volume (Vf). Regarding WSC and HSC, the microstructure of WS and HS had a significant effect on the physical and mechanical properties. The high porosity influenced the results obtained, since it decreased compressive strength and bulk density; however, thermal conductivity, hygroscopicity, and vapor resistance showed better behavior in most cases than the control specimens, i.e., without bio-aggregates.
- 3 November 2022
- Published by MDPI AG in Sustainability
- Vol. 14 (21) , 14397
Open AccessSustainable Proposal for Plant-Based Cementitious Composites, Evaluation of Their Mechanical, Durability and Comfort Properties
This research evaluates four sustainable cementitious composites with sustainable plant fibers and bio-aggregates: (1) cementitious matrix composite with lechuguilla fibers (LFC) and (2) with flax fibers (FFC); and (3) cementitious matrix composite with wood shavings (WSC) and (4) with hemp shavings (HSC). The fibers are for reinforcement and the shavings act as bio-aggregates as a total replacement for limestone aggregates. The lechuguilla (LF) and flax (FF) fibers were treated; wood (WS) and hemp (HS) bio-aggregates were also processed. Nineteen mixtures were manufactured, and five were used as controls, and the hygrothermal, mechanical, and durability properties were evaluated. The results for LFC and FFC showed that fiber treatment negatively affected flexural–compressive strength; untreated LFC with accelerated deterioration had better mechanical behavior, higher density, and lower porosity than FFC. Strength and density decreased, but porosity increased with increasing fiber volume (Vf). Regarding WSC and HSC, the microstructure of WS and HS had a significant effect on the physical and mechanical properties. The high porosity influenced the results obtained, since it decreased compressive strength and bulk density; however, thermal conductivity, hygroscopicity, and vapor resistance showed better behavior in most cases than the control specimens, i.e., without bio-aggregates.
- Open Access
Development of a Portland Cement-Based Material with Agave salmiana Leaves Bioaggregate
Depending on the morphology of the natural fibers, they can be used as reinforcement to improve flexural strength in cement-based composites or as aggregates to improve thermal conductivity properties. In this last aspect, hemp, coconut, flax, sunflower, and corn fibers have been used extensively, and further study is expected into different bioaggregates that allow diversifying of the raw materials. The objective of the research was to develop plant-based concretes with a matrix based on Portland cement and an aggregate of Agave salmiana (AS) leaves, obtained from the residues of the tequila industry that have no current purpose, as a total replacement for the calcareous aggregates commonly used in the manufacturing of mortars and whose extraction is associated with high levels of pollution, to improve their thermal properties and reduce the energy demand for air conditioning in homes. Characterization tests were carried out on the raw materials and the vegetal aggregate was processed to improve its compatibility with the cement paste through four different treatments: (a) freezing (T/C), (b) hornification (T/H), (c) sodium hydroxide (T/NaOH), and (d) solid paraffin (T/P). The effect of the treatments on the physical properties of the resulting composite was evaluated by studying the vegetal concrete under thermal conductivity, bulk density, and compressive strength tests with a volumetric ratio between the vegetal aggregate and the cement paste of 0.36 and a water/cement ratio of 0.35. The hornification treatment showed a 15.2% decrease in the water absorption capacity of the aggregate, resulting in a composite with a thermal conductivity of 0.49 W/mK and a compressive strength of 8.66 MPa, which allows its utilization as a construction material to produce prefabricated blocks.
Open AccessDevelopment of a Portland Cement-Based Material with Agave salmiana Leaves Bioaggregate
Depending on the morphology of the natural fibers, they can be used as reinforcement to improve flexural strength in cement-based composites or as aggregates to improve thermal conductivity properties. In this last aspect, hemp, coconut, flax, sunflower, and corn fibers have been used extensively, and further study is expected into different bioaggregates that allow diversifying of the raw materials. The objective of the research was to develop plant-based concretes with a matrix based on Portland cement and an aggregate of Agave salmiana (AS) leaves, obtained from the residues of the tequila industry that have no current purpose, as a total replacement for the calcareous aggregates commonly used in the manufacturing of mortars and whose extraction is associated with high levels of pollution, to improve their thermal properties and reduce the energy demand for air conditioning in homes. Characterization tests were carried out on the raw materials and the vegetal aggregate was processed to improve its compatibility with the cement paste through four different treatments: (a) freezing (T/C), (b) hornification (T/H), (c) sodium hydroxide (T/NaOH), and (d) solid paraffin (T/P). The effect of the treatments on the physical properties of the resulting composite was evaluated by studying the vegetal concrete under thermal conductivity, bulk density, and compressive strength tests with a volumetric ratio between the vegetal aggregate and the cement paste of 0.36 and a water/cement ratio of 0.35. The hornification treatment showed a 15.2% decrease in the water absorption capacity of the aggregate, resulting in a composite with a thermal conductivity of 0.49 W/mK and a compressive strength of 8.66 MPa, which allows its utilization as a construction material to produce prefabricated blocks.
- Open Access
- 1 January 2022
- Published by FapUNIFESP (SciELO) in Cadernos de Saude Publica
- Vol. 38 (1) , e00288920
Quality of automatic geocoding tools: a study using addresses from hospital record files in Temuco, Chile
Automatic geocoding methods have become popular in recent years, facilitating the study of the association between health outcomes and the place of living. However, rather few studies have evaluated geocoding quality, with most of them being performed in the US and Europe. This article aims to compare the quality of three automatic online geocoding tools against a reference method. A subsample of 300 handwritten addresses from hospital records was geocoded using Bing, Google Earth, and Google Maps. Match rates were higher (> 80%) for Google Maps and Google Earth compared with Bing. However, the accuracy of the addresses was better for Bing with a larger proportion (> 70%) of addresses with positional errors below 20m. Generally, performance did not vary for each method for different socioeconomic status. Overall, the methods showed an acceptable, but heterogeneous performance, which may be a warning against the use of automatic methods without assessing quality in other municipalities, particularly in Chile and Latin America.
- 1 January 2022
- Published by FapUNIFESP (SciELO) in Cadernos de Saude Publica
- Vol. 38 (1) , e00288920
Open AccessQuality of automatic geocoding tools: a study using addresses from hospital record files in Temuco, Chile
Automatic geocoding methods have become popular in recent years, facilitating the study of the association between health outcomes and the place of living. However, rather few studies have evaluated geocoding quality, with most of them being performed in the US and Europe. This article aims to compare the quality of three automatic online geocoding tools against a reference method. A subsample of 300 handwritten addresses from hospital records was geocoded using Bing, Google Earth, and Google Maps. Match rates were higher (> 80%) for Google Maps and Google Earth compared with Bing. However, the accuracy of the addresses was better for Bing with a larger proportion (> 70%) of addresses with positional errors below 20m. Generally, performance did not vary for each method for different socioeconomic status. Overall, the methods showed an acceptable, but heterogeneous performance, which may be a warning against the use of automatic methods without assessing quality in other municipalities, particularly in Chile and Latin America.