Xiaohong Deng
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Xiaohong Deng has a total of 18 co-authors. Here are the top co-authors by number of shared publications:
- Junjie Wu
Institute of Geophysical and Geochemical Exploration, Chinese Academy of Geological Sciences, Langfang 065000, China
6 shared publications - Xingchun Wang
Institute of Geophysical and Geochemical Exploration, Chinese Academy of Geological Sciences , Tianjin 300300
6 shared publications - Qingquan Zhi
Institute of Geophysical and Geochemical Exploration, Chinese Academy of Geological Sciences, Langfang 065000, China
4 shared publications - Yue Huang
Institute of Geophysical and Geochemical Exploration, Chinese Academy of Geological Sciences, Langfang 065000, China
3 shared publications - Qingquan Zhi
State Key Laboratory of Deep Earth Exploration and Imaging, The Institute of Geophysical and Geochemical Exploration, CAGS, Dongli, Tianjin 300300, China
2 shared publications - Yi Yang
Institute of Geophysical and Geochemical Exploration, Chinese Academy of Geological Sciences, Langfang 065000, China
2 shared publications
Latest Publications
- Open Access
Anomaly Field Extraction Based on Layered-Earth Model and Equivalent Eddy Current Inversion: A Case Study of Borehole zk506 in Baishiquan, Xinjiang
Based on the concept of an equivalent eddy current, anomaly field inversion provides an efficient and rapid inversion method for borehole transient electromagnetic (BHTEM) measurements. It enables the utilization of the equivalent eddy current to rapidly process and interpret BHTEM data. This method allows for the accurate determination of the central position and spatial distribution of anomalies. However, the equivalent eddy current method is solely applicable to the inversion of the anomaly field. Given that the measured data frequently contain strong background field information, it is challenging to directly apply the equivalent eddy current approach to the inversion and interpretation of the measured data. To address the aforementioned issues, in this study, we innovatively put forward a method. Specifically, we utilize the response of the layered earth to simulate the background field and subtract the background field from the measured data through the “difference method” to extract the anomaly field. Subsequently, by integrating the equivalent eddy current method, the inversion of the anomaly field was accomplished. Eventually, a rapid quantitative inversion and interpretation of BHTEM data were achieved. We applied this approach to extract the pure anomaly from the measured data of the zk506 borehole in the Baishiquan mining area, Xinjiang, and then conducted equivalent eddy current inversion. The spatial position and distribution characteristics of the concealed ore bodies near the zk506 borehole were successfully pinpointed. Validation by the zk507 and zk508 boreholes confirmed that the main anomaly of the nickel ore body is positioned in the southeast of the boreholes, dipping northwestward. This outcome validates the accuracy of the BHTEM inversion interpretation and rectifies the geological understanding obtained from the zk506 single borehole. It demonstrates the effectiveness and significance of the pure anomaly extraction based on the layered-earth model and equivalent eddy current inversion in the exploration of high-conductivity sulfide ores.
Open AccessAnomaly Field Extraction Based on Layered-Earth Model and Equivalent Eddy Current Inversion: A Case Study of Borehole zk506 in Baishiquan, Xinjiang
Based on the concept of an equivalent eddy current, anomaly field inversion provides an efficient and rapid inversion method for borehole transient electromagnetic (BHTEM) measurements. It enables the utilization of the equivalent eddy current to rapidly process and interpret BHTEM data. This method allows for the accurate determination of the central position and spatial distribution of anomalies. However, the equivalent eddy current method is solely applicable to the inversion of the anomaly field. Given that the measured data frequently contain strong background field information, it is challenging to directly apply the equivalent eddy current approach to the inversion and interpretation of the measured data. To address the aforementioned issues, in this study, we innovatively put forward a method. Specifically, we utilize the response of the layered earth to simulate the background field and subtract the background field from the measured data through the “difference method” to extract the anomaly field. Subsequently, by integrating the equivalent eddy current method, the inversion of the anomaly field was accomplished. Eventually, a rapid quantitative inversion and interpretation of BHTEM data were achieved. We applied this approach to extract the pure anomaly from the measured data of the zk506 borehole in the Baishiquan mining area, Xinjiang, and then conducted equivalent eddy current inversion. The spatial position and distribution characteristics of the concealed ore bodies near the zk506 borehole were successfully pinpointed. Validation by the zk507 and zk508 boreholes confirmed that the main anomaly of the nickel ore body is positioned in the southeast of the boreholes, dipping northwestward. This outcome validates the accuracy of the BHTEM inversion interpretation and rectifies the geological understanding obtained from the zk506 single borehole. It demonstrates the effectiveness and significance of the pure anomaly extraction based on the layered-earth model and equivalent eddy current inversion in the exploration of high-conductivity sulfide ores.
- Open Access
- 29 August 2024
- Published by MDPI AG in Remote Sensing
- Vol. 16 (17) , 3186
Exploring Shallow Geological Structures in Landslides Using the Semi-Airborne Transient Electromagnetic Method
The Meijiayan landslide in Pengshui County within Chongqing City is a medium-scale soil landslide triggered by the excavation of roadbeds. To delve into the influencing factors and assess the stability of this landslide, it is crucial to meticulously map the subterranean geological framework of the area. Such an analysis lays the groundwork for evaluating and mitigating the risks of future landslide instabilities. In this context, the semi-airborne transient electromagnetic method (SATEM), which is complemented by a receiving system mounted on an aerial platform, stands out as an innovative geophysical exploration technique. This method is adept at conducting swift measurements across complex terrains, making it particularly valuable for areas prone to such geological events. This paper presents the utilization of a cutting-edge loop source SATEM system, which was operationalized via a rotor-based unmanned aerial vehicle (UAV). The system was employed to conduct shallow geological structure detection experiments on the Meijiayan landslide. The SATEM detection outcomes have unveiled fluctuations in the electrical distribution across the upper strata, which are indicative of the subsurface geological boundaries, faults, and areas potentially rich in water within the landslide region. These discoveries affirm the viability of utilizing loop source SATEM for the identification of shallow geological structures in regions susceptible to landslides. The findings indicate that while the landslide is currently in a stable condition, it poses a significant risk of movement, especially during the rainy season, with the potential for landslides to be exacerbated by extreme or sustained rainfall events.
- 29 August 2024
- Published by MDPI AG in Remote Sensing
- Vol. 16 (17) , 3186
Open AccessExploring Shallow Geological Structures in Landslides Using the Semi-Airborne Transient Electromagnetic Method
The Meijiayan landslide in Pengshui County within Chongqing City is a medium-scale soil landslide triggered by the excavation of roadbeds. To delve into the influencing factors and assess the stability of this landslide, it is crucial to meticulously map the subterranean geological framework of the area. Such an analysis lays the groundwork for evaluating and mitigating the risks of future landslide instabilities. In this context, the semi-airborne transient electromagnetic method (SATEM), which is complemented by a receiving system mounted on an aerial platform, stands out as an innovative geophysical exploration technique. This method is adept at conducting swift measurements across complex terrains, making it particularly valuable for areas prone to such geological events. This paper presents the utilization of a cutting-edge loop source SATEM system, which was operationalized via a rotor-based unmanned aerial vehicle (UAV). The system was employed to conduct shallow geological structure detection experiments on the Meijiayan landslide. The SATEM detection outcomes have unveiled fluctuations in the electrical distribution across the upper strata, which are indicative of the subsurface geological boundaries, faults, and areas potentially rich in water within the landslide region. These discoveries affirm the viability of utilizing loop source SATEM for the identification of shallow geological structures in regions susceptible to landslides. The findings indicate that while the landslide is currently in a stable condition, it poses a significant risk of movement, especially during the rainy season, with the potential for landslides to be exacerbated by extreme or sustained rainfall events.
- Open Access
Joint Inversion with Borehole and Semi-Airborne TEM Data Based on Equivalent Filament Approximation
The borehole transient electromagnetic (TEM) method can be useful in deep mineral exploration to detect blind ore bodies beside or below the borehole, and is especially adapted to finding small-scale, deep, rich ore bodies. In this method a transmitting loop is deployed on the top surface of the Earth, while a receiving coil is moved down the borehole. As the borehole TEM method is limited by the borehole’s location and depth, so its exploration scope is limited. The surface to airborne TEM method is a semi-airborne TEM configuration that transmits on the surface and receives TEM response in air. The two systems are combined into one system in this study, sharing the transmission loop deployed on the surface. With this combined system, the TEM response in the borehole and in the air can be observed at the same time. This paper employs a joint interpretation method based on the equivalent filament, which is introduced to obtain more reliable geometric information for the target with both borehole and aerial TEM data. The eddy currents induced in a thin confined conductor can be represented by equivalent current filaments, and the distribution of filaments can reflect the position and geometry of the conductor. Therefore, geometric parameters of targets can be obtained by filament inversion, and the joint inversion can be more accurate with both borehole and aerial response. Numerical modeling results show that the joint inversion based on the equivalent filament results can reliably obtain the geometric parameters of the thin conductive plate embedded in half space.
Open AccessJoint Inversion with Borehole and Semi-Airborne TEM Data Based on Equivalent Filament Approximation
The borehole transient electromagnetic (TEM) method can be useful in deep mineral exploration to detect blind ore bodies beside or below the borehole, and is especially adapted to finding small-scale, deep, rich ore bodies. In this method a transmitting loop is deployed on the top surface of the Earth, while a receiving coil is moved down the borehole. As the borehole TEM method is limited by the borehole’s location and depth, so its exploration scope is limited. The surface to airborne TEM method is a semi-airborne TEM configuration that transmits on the surface and receives TEM response in air. The two systems are combined into one system in this study, sharing the transmission loop deployed on the surface. With this combined system, the TEM response in the borehole and in the air can be observed at the same time. This paper employs a joint interpretation method based on the equivalent filament, which is introduced to obtain more reliable geometric information for the target with both borehole and aerial TEM data. The eddy currents induced in a thin confined conductor can be represented by equivalent current filaments, and the distribution of filaments can reflect the position and geometry of the conductor. Therefore, geometric parameters of targets can be obtained by filament inversion, and the joint inversion can be more accurate with both borehole and aerial response. Numerical modeling results show that the joint inversion based on the equivalent filament results can reliably obtain the geometric parameters of the thin conductive plate embedded in half space.
- Open Access
Improving Inversion Quality of IP-Affected TEM Data Using Dual Source
The induced polarization (IP) effects in transient electromagnetic (TEM) responses pose difficulties to the TEM data interpretation and inversion. The IP effects break the monotony in TEM decay curves and can even cause sign reversals and lead to the singularity and non-monotony of inversion. The singularity problem is still urgent to be solved. In this paper, the forward modeling method of IP-affected TEM responses is developed using the Cole–Cole model and a frequency-time domain transformation. A TEM data acquisition scheme using a dual-source method without a significant increase in field work is proposed to weaken the singularity and improve the inversion quality finally. Based on the modeling and analysis, the dual-source scheme is designed to guarantee all stations be measured twice with different loops. The joint inversion of dual-source datasets is realized by using an objective combing function and the particle swarm optimization (PSO) algorithm. The synthetic data test proved the validity of the algorithm and illustrated that the joint dual-source method greatly weakened the singularity and stabilized the inversion. The field example of the Baiyun golden deposit showed well consistency with resistivity logging and TEM logging results and predicted the gold mineralization below 2000 m.
Open AccessImproving Inversion Quality of IP-Affected TEM Data Using Dual Source
The induced polarization (IP) effects in transient electromagnetic (TEM) responses pose difficulties to the TEM data interpretation and inversion. The IP effects break the monotony in TEM decay curves and can even cause sign reversals and lead to the singularity and non-monotony of inversion. The singularity problem is still urgent to be solved. In this paper, the forward modeling method of IP-affected TEM responses is developed using the Cole–Cole model and a frequency-time domain transformation. A TEM data acquisition scheme using a dual-source method without a significant increase in field work is proposed to weaken the singularity and improve the inversion quality finally. Based on the modeling and analysis, the dual-source scheme is designed to guarantee all stations be measured twice with different loops. The joint inversion of dual-source datasets is realized by using an objective combing function and the particle swarm optimization (PSO) algorithm. The synthetic data test proved the validity of the algorithm and illustrated that the joint dual-source method greatly weakened the singularity and stabilized the inversion. The field example of the Baiyun golden deposit showed well consistency with resistivity logging and TEM logging results and predicted the gold mineralization below 2000 m.
- Open Access
Multicomponent Transient Electromagnetic Exploration Technology and Its Application
To take full advantage of the multicomponent transient electromagnetic method, we summarize the advantages of multicomponent exploration based on simulation calculation. We have carried out experiments on the effectiveness of the method in the known copper-nickel mining area. The results show that the characteristic curve of the horizontal component can effectively point to the central direction of the low-resistivity ore body and reflect the occurrence of the ore body. The degree of coupling between the vertical component and the ore body is high, which is beneficial for quantitative inversion. The results for the horizontal component and vertical component interpretations are consistent, which reduces the limitation of conventional single vertical component interpretation and effectively improves the work efficiency in field work.
Open AccessMulticomponent Transient Electromagnetic Exploration Technology and Its Application
To take full advantage of the multicomponent transient electromagnetic method, we summarize the advantages of multicomponent exploration based on simulation calculation. We have carried out experiments on the effectiveness of the method in the known copper-nickel mining area. The results show that the characteristic curve of the horizontal component can effectively point to the central direction of the low-resistivity ore body and reflect the occurrence of the ore body. The degree of coupling between the vertical component and the ore body is high, which is beneficial for quantitative inversion. The results for the horizontal component and vertical component interpretations are consistent, which reduces the limitation of conventional single vertical component interpretation and effectively improves the work efficiency in field work.
- Open Access
Deep Gold Exploration with SQUID TEM in the Qingchengzi Orefield, Eastern Liaoning, Northeast China
The Qingchengzi orefield is an important polymetallic ore concentration zone in the northern margin of the North China Craton (NCC). The region has significant metallogenic potential for deep mining. Many areas with gold mineralization have been found in the shallow area of Taoyuan–Xiaotongjiapuzi–Linjiasandaogou in the east of the Qingchengzi orefield. To assess the distribution of mineralization levels, we carried out deep exploration using the transient electromagnetic method (TEM). A superconductive quantum interference device (SQUID) magnetometer and a conventional induction coil were used for field data acquisition. The SQUID data inversion results reflect the bottom interface of the high-conductivity area, the fold state of the underlying dolomite marble stratum, and the deep structural characteristics of the syncline. Secondary crumples appear in the inversion results of the southern segment of TEM, which is inferred as a favorable area for deep gold mineralization. Negative values appear in the SQUID data of some stations, to varying degrees. This induced polarization phenomenon may be related to deep gold mineralization.
Open AccessDeep Gold Exploration with SQUID TEM in the Qingchengzi Orefield, Eastern Liaoning, Northeast China
The Qingchengzi orefield is an important polymetallic ore concentration zone in the northern margin of the North China Craton (NCC). The region has significant metallogenic potential for deep mining. Many areas with gold mineralization have been found in the shallow area of Taoyuan–Xiaotongjiapuzi–Linjiasandaogou in the east of the Qingchengzi orefield. To assess the distribution of mineralization levels, we carried out deep exploration using the transient electromagnetic method (TEM). A superconductive quantum interference device (SQUID) magnetometer and a conventional induction coil were used for field data acquisition. The SQUID data inversion results reflect the bottom interface of the high-conductivity area, the fold state of the underlying dolomite marble stratum, and the deep structural characteristics of the syncline. Secondary crumples appear in the inversion results of the southern segment of TEM, which is inferred as a favorable area for deep gold mineralization. Negative values appear in the SQUID data of some stations, to varying degrees. This induced polarization phenomenon may be related to deep gold mineralization.