Tran Van Hau
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Tran Van Hau has a total of 61 co-authors. Here are the top co-authors by number of shared publications:
- Pham Van Trinh
Institute of Materials Science, Vietnam Academy of Science and Technology
10 shared publications Nguyen Van Tu
Institute of Materials Science, Vietnam Academy of Science and Technology, 18 Hoang Quoc Viet Str., Nghia Do Ward, Hanoi, Vietnam
9 shared publicationsPhan Ngoc Minh
Graduate University of Science and Technology, Vietnam Academy of Science and Technology, 18 Hoang Quoc Viet Str., Nghia Do Ward, Hanoi, Vietnam
9 shared publicationsBui Hung Thang
Graduate University of Science and Technology, Vietnam Academy of Science and Technology, 18 Hoang Quoc Viet Str., Nghia Do Ward, Hanoi, Vietnam
5 shared publicationsNguyen Thi Huyen
Institute of Materials Science, Vietnam Academy of Science and Technology, 18 Hoang Quoc Viet Str., Cau Giay Distr., Hanoi, Vietnam
5 shared publications- Nguyen Van Chuc
Institute of Materials Science, Vietnam Academy of Science and Technology, Hanoi, Vietnam
5 shared publications
Latest Publications
- Open Access
- 23 September 2026
- Published by Royal Society of Chemistry (RSC) in RSC Advances
- Vol. 16 (42) , 51106-51115
Thermal conductivity enhancement and predictive modeling of BNNP-paraffin nanofluids: synergistic effects of BNNP concentration and temperature
Stability and thermal conductivity of BNNP-paraffin nanofluids were investigated.
- 23 September 2026
- Published by Royal Society of Chemistry (RSC) in RSC Advances
- Vol. 16 (42) , 51106-51115
Open AccessThermal conductivity enhancement and predictive modeling of BNNP-paraffin nanofluids: synergistic effects of BNNP concentration and temperature
Stability and thermal conductivity of BNNP-paraffin nanofluids were investigated.
- Open Access
- 7 April 2026
- Published by Royal Society of Chemistry (RSC) in RSC Advances
- Vol. 16 (20) , 18093-18103
Self-supporting cotton-derived 3D carbon–Si nanoarchitecture for solvent-free fabrication of high-performance lithium-ion anodes
Binder-free 3D carbon framework with embedded Si nanoparticles enables enhanced conductivity, structural stability, and high-performance Li-ion battery anodes.
- 7 April 2026
- Published by Royal Society of Chemistry (RSC) in RSC Advances
- Vol. 16 (20) , 18093-18103
Open AccessSelf-supporting cotton-derived 3D carbon–Si nanoarchitecture for solvent-free fabrication of high-performance lithium-ion anodes
Binder-free 3D carbon framework with embedded Si nanoparticles enables enhanced conductivity, structural stability, and high-performance Li-ion battery anodes.
- Open Access
- 13 January 2026
- Published by Royal Society of Chemistry (RSC) in RSC Advances
- Vol. 16 (4) , 3753-3764
Experimental study on the thermal conductivity of graphene–carbon nanotube–silver nanoparticle ternary hybrid nanofluids
Graphene–carbon nanotube–silver nanoparticle ternary hybrid nanofluids were prepared and investigated.
- 13 January 2026
- Published by Royal Society of Chemistry (RSC) in RSC Advances
- Vol. 16 (4) , 3753-3764
Open AccessExperimental study on the thermal conductivity of graphene–carbon nanotube–silver nanoparticle ternary hybrid nanofluids
Graphene–carbon nanotube–silver nanoparticle ternary hybrid nanofluids were prepared and investigated.
- Open Access
- 12 January 2026
- Published by IOP Publishing in Materials Research Express
- Vol. 13 (3)
Synergistic Strengthening and Solid-Lubrication Effects of Hydroxyl-Functionalized Boron Nitride Nanosheets in Ni-Mo Composite Coatings
In the present work, hydroxyl-functionalized boron nitride nanosheets (BNNS-OH) synthesized via alkaline-assisted high-energy ball milling were co-electrodeposited into Ni-Mo alloy coatings to examine their effects on grain refinement, hardness, friction coefficient, and wear resistance. Ni-Mo/BNNS-OH composite coatings with BNNS-OH contents ranging from 0 to 0.5 g/L were produced using direct current electrodeposition. It was observed that the incorporation of BNNS-OH refined the grain structure, increased nucleation density, and promoted a uniform nanosheet distribution within the Ni-Mo matrix. At an optimal loading of 0.3 g/L, the composite coating achieved a microhardness of 523.69 9.86 HV, a stable friction coefficient of 0.28 - 0.35, and a reduced wear rate of 8.72 × 10-6 mm3/Nm, outperforming pristine Ni-Mo. The performance enhancements were rationalized by synergistic contributions of microstructural strengthening and solid-lubrication effects. Excessive BNNS-OH content led to nanosheet agglomeration and a subsequent decline in mechanical and tribological properties. These findings highlight BNNS-OH as a promising reinforcement strategy for developing environmentally benign, high-durability coatings for advanced tribological applications.
- 12 January 2026
- Published by IOP Publishing in Materials Research Express
- Vol. 13 (3)
Open AccessSynergistic Strengthening and Solid-Lubrication Effects of Hydroxyl-Functionalized Boron Nitride Nanosheets in Ni-Mo Composite Coatings
In the present work, hydroxyl-functionalized boron nitride nanosheets (BNNS-OH) synthesized via alkaline-assisted high-energy ball milling were co-electrodeposited into Ni-Mo alloy coatings to examine their effects on grain refinement, hardness, friction coefficient, and wear resistance. Ni-Mo/BNNS-OH composite coatings with BNNS-OH contents ranging from 0 to 0.5 g/L were produced using direct current electrodeposition. It was observed that the incorporation of BNNS-OH refined the grain structure, increased nucleation density, and promoted a uniform nanosheet distribution within the Ni-Mo matrix. At an optimal loading of 0.3 g/L, the composite coating achieved a microhardness of 523.69 9.86 HV, a stable friction coefficient of 0.28 - 0.35, and a reduced wear rate of 8.72 × 10-6 mm3/Nm, outperforming pristine Ni-Mo. The performance enhancements were rationalized by synergistic contributions of microstructural strengthening and solid-lubrication effects. Excessive BNNS-OH content led to nanosheet agglomeration and a subsequent decline in mechanical and tribological properties. These findings highlight BNNS-OH as a promising reinforcement strategy for developing environmentally benign, high-durability coatings for advanced tribological applications.
- Open Access
- 12 December 2025
- Published by MDPI AG in Inorganics
- Vol. 13 (12) , 405
Comparison Study on the Microstructure, Hardness and Wear Properties of Ti Alloy Composites Reinforced by Carbon Nanomaterials
In this study, titanium alloy-based composites reinforced with carbon nanotubes (CNTs) and graphene (Gr) were fabricated via spark plasma sintering (SPS). The effects of CNT and Gr reinforcements on the microstructure, density, hardness, and tribological properties of the composites were systematically investigated. The results revealed that CNTs and Gr were dispersed within the Ti alloy matrix. All composites exhibited high relative densities about 99%, confirming the strong densification capability of the SPS process. The incorporation of CNTs and Gr significantly enhanced the mechanical performance of the composites. The maximum hardness values of 445.8 HV and 430.5 HV were obtained for CNT/Ti and Gr/Ti composites containing 3 vol.% reinforcement, corresponding to improvements of 34% and 30%, respectively, compared with the unreinforced Ti alloy. Tribological tests further revealed notable reductions in the coefficient of friction and wear rate for both CNT/Ti and Gr/Ti composites. These enhancements are attributed to the formation of a lubricating tribo-film composed of carbonaceous species and oxide particles (TiO2, Al2O3) on the worn surfaces. Among the two reinforcements, the obtained results indicated that CNTs are more effective in enhancing hardness, whereas graphene provides superior improvement in wear resistance of Ti alloy-based composites. Overall, this work demonstrated that the combination of Ti alloys with nanocarbon reinforcements is an effective approach to simultaneously enhance their mechanical and tribological performance.
- 12 December 2025
- Published by MDPI AG in Inorganics
- Vol. 13 (12) , 405
Open AccessComparison Study on the Microstructure, Hardness and Wear Properties of Ti Alloy Composites Reinforced by Carbon Nanomaterials
In this study, titanium alloy-based composites reinforced with carbon nanotubes (CNTs) and graphene (Gr) were fabricated via spark plasma sintering (SPS). The effects of CNT and Gr reinforcements on the microstructure, density, hardness, and tribological properties of the composites were systematically investigated. The results revealed that CNTs and Gr were dispersed within the Ti alloy matrix. All composites exhibited high relative densities about 99%, confirming the strong densification capability of the SPS process. The incorporation of CNTs and Gr significantly enhanced the mechanical performance of the composites. The maximum hardness values of 445.8 HV and 430.5 HV were obtained for CNT/Ti and Gr/Ti composites containing 3 vol.% reinforcement, corresponding to improvements of 34% and 30%, respectively, compared with the unreinforced Ti alloy. Tribological tests further revealed notable reductions in the coefficient of friction and wear rate for both CNT/Ti and Gr/Ti composites. These enhancements are attributed to the formation of a lubricating tribo-film composed of carbonaceous species and oxide particles (TiO2, Al2O3) on the worn surfaces. Among the two reinforcements, the obtained results indicated that CNTs are more effective in enhancing hardness, whereas graphene provides superior improvement in wear resistance of Ti alloy-based composites. Overall, this work demonstrated that the combination of Ti alloys with nanocarbon reinforcements is an effective approach to simultaneously enhance their mechanical and tribological performance.
- Open Access
- 8 December 2025
- Published by Royal Society of Chemistry (RSC) in RSC Advances
- Vol. 15 (57) , 48795-48806
SiC coated, CNT nanowire reinforced copper composite: preparation, microstructure and properties
Copper matrix composites are engineering materials widely used in electrical and electronic applications. Therefore, enhancing their mechanical, electrical and thermal properties is essential. In this work, some results on the preparation of silicon carbide coated carbon nanotube nanowire (SiC@CNT NWs) reinforced copper (Cu) matrix composites were presented. SiC@CNT NWs prepared using a chemical vapor deposition method were mixed with Cu powder and then consolidated by spark plasma sintering to obtain SiC@CNTNW/Cu composites. The effects of SiC@CNT NW content on the microstructure, mechanical properties, tribological behavior, electrical and thermal properties were examined. Incorporation of 3 vol% SiC@CNT NWs enhanced hardness and ultimate tensile strength by 71% and 64%, respectively, while reducing the coefficient of friction (COF) by 40% and specific wear rate by 53%. These improvements are attributed to the SiC@CNT structure, which offers superior reinforcement efficiency. The coefficient of thermal expansion decreased with increasing nanowire fraction, consistent with the inherently lower CTE of SiC@CNT NWs. Based on Turner's model, the CTE and Young's modulus of the nanowires were estimated at 1.8 × 10−6 K−1 and 680 GPa, respectively.
- 8 December 2025
- Published by Royal Society of Chemistry (RSC) in RSC Advances
- Vol. 15 (57) , 48795-48806
Open AccessSiC coated, CNT nanowire reinforced copper composite: preparation, microstructure and properties
Copper matrix composites are engineering materials widely used in electrical and electronic applications. Therefore, enhancing their mechanical, electrical and thermal properties is essential. In this work, some results on the preparation of silicon carbide coated carbon nanotube nanowire (SiC@CNT NWs) reinforced copper (Cu) matrix composites were presented. SiC@CNT NWs prepared using a chemical vapor deposition method were mixed with Cu powder and then consolidated by spark plasma sintering to obtain SiC@CNTNW/Cu composites. The effects of SiC@CNT NW content on the microstructure, mechanical properties, tribological behavior, electrical and thermal properties were examined. Incorporation of 3 vol% SiC@CNT NWs enhanced hardness and ultimate tensile strength by 71% and 64%, respectively, while reducing the coefficient of friction (COF) by 40% and specific wear rate by 53%. These improvements are attributed to the SiC@CNT structure, which offers superior reinforcement efficiency. The coefficient of thermal expansion decreased with increasing nanowire fraction, consistent with the inherently lower CTE of SiC@CNT NWs. Based on Turner's model, the CTE and Young's modulus of the nanowires were estimated at 1.8 × 10−6 K−1 and 680 GPa, respectively.
- Open Access
- 4 April 2025
- Published by Royal Society of Chemistry (RSC) in RSC Advances
- Vol. 15 (14) , 10754-10762
Efficient photocatalytic degradation of methylene blue using 3D urchin-like TiO2@rGO-hBN architecture
3D urchin-like TiO2@rGO-hBN architectures were produced by a hydrothermal method, followed by a cold plasma jet process.
- 4 April 2025
- Published by Royal Society of Chemistry (RSC) in RSC Advances
- Vol. 15 (14) , 10754-10762
Open AccessEfficient photocatalytic degradation of methylene blue using 3D urchin-like TiO2@rGO-hBN architecture
3D urchin-like TiO2@rGO-hBN architectures were produced by a hydrothermal method, followed by a cold plasma jet process.
- Open Access
- 26 March 2025
- Published by Royal Society of Chemistry (RSC) in Materials Advances
- Vol. 6 (8) , 2691-2700
A new and facile preparation of 3D urchin-like TiO 2 @graphene core@shell SERS substrates for photocatalytic degradation of RhB
Fabrication procedure and RhB degradation of TiO 2 @graphene SERS substrates under irradiation of UV light.
- 26 March 2025
- Published by Royal Society of Chemistry (RSC) in Materials Advances
- Vol. 6 (8) , 2691-2700
Open AccessA new and facile preparation of 3D urchin-like TiO 2 @graphene core@shell SERS substrates for photocatalytic degradation of RhB
Fabrication procedure and RhB degradation of TiO 2 @graphene SERS substrates under irradiation of UV light.
- 14 August 2023
- Published by Elsevier in Materials Letters
- Vol. 352, 135054
Hexagonal boron nitride nanosheets reinforcing Ni-Mo alloy coating for improved wear resistance
- 14 August 2023
- Published by Elsevier in Materials Letters
- Vol. 352, 135054
Hexagonal boron nitride nanosheets reinforcing Ni-Mo alloy coating for improved wear resistance