Elena Naidenko
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Elena Naidenko has a total of 14 co-authors. Here are the top co-authors by number of shared publications:
- Andrii Boiko
Odesa Polytechnic National University
9 shared publications - Oleksandr Besarab
Odesa Polytechnic National University
5 shared publications - Oleksandr Bondar
Odessa Polytechnic National University
5 shared publications - Aleksey Tkachev
Odesa Polytechnic National University
2 shared publications - Anatoliy Tkachev
Odesa Polytechnic National University
2 shared publications - Oleksandr Fomin
Odesа Polytechnic National University
2 shared publications
Latest Publications
- 17 January 2026
- Published by Springer Nature
- p. 255-264
The Influence of Residual Deformations of a Crane Bridge on Its Load-Bearing Capacity
- 17 January 2026
- Published by Springer Nature
- p. 255-264
The Influence of Residual Deformations of a Crane Bridge on Its Load-Bearing Capacity
- 17 January 2026
- Published by Springer Nature
- p. 390-402
Formation of Industrial Work Movement Diagrams at Position Control
- 17 January 2026
- Published by Springer Nature
- p. 390-402
Formation of Industrial Work Movement Diagrams at Position Control
- 14 February 2025
- Published by Springer Nature
- p. 491-501
Dynamics Analysis of Elevator Winches with Thyristor Control System
- 14 February 2025
- Published by Springer Nature
- p. 491-501
Dynamics Analysis of Elevator Winches with Thyristor Control System
- 6 July 2024
- Published by Springer Nature
- p. 3-13
Optimization of the Counterweight Mass of a Passenger Elevator
- 6 July 2024
- Published by Springer Nature
- p. 3-13
Optimization of the Counterweight Mass of a Passenger Elevator
- 1 April 2024
- Published by Technical University of Moldova in Problems of the Regional Energetics
- No. 2(62),p. 28-37
Study of Start-up and Shutdown Modes of an Asynchronous Electric Drive for a Centrifugal Pump
The aim of this study is to investigate the commutation processes of an asynchronous short-circuited electric drive for a centrifugal pump. The set goal is achieved by solving two tasks: analyzing the dynamic modes of connection to and disconnection from the network of the asynchronous motor of the centrifugal pump for a given power supply scheme; assessing the qualitative and quantitative indicators of the transient processes of the electric drive. Among the most significant results of the study, it is possible to highlight the ability to form practical recommendations on the operation peculiarities of electric drives for a wide class of mechanisms. The conducted research allowed asserting that in an electrical system with capacitors directly connected to the stator winding and during both the connection and disconnection of the drive motor of the centrifugal pump, voltages significantly exceeding the nominal ones may occur. It has been determined that considering the harsh operating conditions of pump units, such overvoltages represent a danger to the motor winding insulation. During the motor disconnection, significant overvoltages on the stator windings are possible if, for any reason, the capacitor's capacitance exceeds the calculated base value for the applied motor. The practical significance of the obtained results lies in the fact that the assumption of the motor transitioning to intensive braking mode and subsequent hydraulic shock upon disconnection from the network due to self-excitation did not prove to be true. The electric drive provides braking under the action of the load torque without mechanical overloads.
- 1 April 2024
- Published by Technical University of Moldova in Problems of the Regional Energetics
- No. 2(62),p. 28-37
Study of Start-up and Shutdown Modes of an Asynchronous Electric Drive for a Centrifugal Pump
The aim of this study is to investigate the commutation processes of an asynchronous short-circuited electric drive for a centrifugal pump. The set goal is achieved by solving two tasks: analyzing the dynamic modes of connection to and disconnection from the network of the asynchronous motor of the centrifugal pump for a given power supply scheme; assessing the qualitative and quantitative indicators of the transient processes of the electric drive. Among the most significant results of the study, it is possible to highlight the ability to form practical recommendations on the operation peculiarities of electric drives for a wide class of mechanisms. The conducted research allowed asserting that in an electrical system with capacitors directly connected to the stator winding and during both the connection and disconnection of the drive motor of the centrifugal pump, voltages significantly exceeding the nominal ones may occur. It has been determined that considering the harsh operating conditions of pump units, such overvoltages represent a danger to the motor winding insulation. During the motor disconnection, significant overvoltages on the stator windings are possible if, for any reason, the capacitor's capacitance exceeds the calculated base value for the applied motor. The practical significance of the obtained results lies in the fact that the assumption of the motor transitioning to intensive braking mode and subsequent hydraulic shock upon disconnection from the network due to self-excitation did not prove to be true. The electric drive provides braking under the action of the load torque without mechanical overloads.
- 31 August 2023
- Published by Springer Nature
- p. 421-431
Analysis of Factors Affecting the Energy Efficiency of an Elevator Winch
- 31 August 2023
- Published by Springer Nature
- p. 421-431
Analysis of Factors Affecting the Energy Efficiency of an Elevator Winch
- 23 May 2023
- Published by Springer Nature
- p. 13-22
Vibration Damping of Lifting Mechanisms for Elevators Using Control Systems
- 23 May 2023
- Published by Springer Nature
- p. 13-22
Vibration Damping of Lifting Mechanisms for Elevators Using Control Systems
- 9 December 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-7
Research on Impedance Matching of Ultrasonic Power Supply
The speed of continuous improvement of technology, and the development speed of modern power technology widely used in power supply in social applications. However, scientists have been unable to solve problems, such as those that tend to arise under normal working conditions with work capacity. Frequency offset phenomenon, how to design transducer impedance matching circuit, and how to realize automatic frequency tracking, etc. Aiming at these problems, this paper studies how to achieve impedance matching by analyzing the equivalent circuit of the transducer. By comparing the impedance matching methods, a series matching circuit is used for impedance matching. The methods and methods of traditional frequency tracking control are analyzed, and the variable-step frequency tracking method is finally determined. On the basis of theoretical analysis, a 3000W ultrasonic power supply prototype is built. The correctness of hardware circuit design and software compilation is verified by experiments, and the automatic frequency tracking effect is observed. The feasibility of the method proposed in this paper is verified based on the analysis of experimental data.
- 9 December 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-7
Research on Impedance Matching of Ultrasonic Power Supply
The speed of continuous improvement of technology, and the development speed of modern power technology widely used in power supply in social applications. However, scientists have been unable to solve problems, such as those that tend to arise under normal working conditions with work capacity. Frequency offset phenomenon, how to design transducer impedance matching circuit, and how to realize automatic frequency tracking, etc. Aiming at these problems, this paper studies how to achieve impedance matching by analyzing the equivalent circuit of the transducer. By comparing the impedance matching methods, a series matching circuit is used for impedance matching. The methods and methods of traditional frequency tracking control are analyzed, and the variable-step frequency tracking method is finally determined. On the basis of theoretical analysis, a 3000W ultrasonic power supply prototype is built. The correctness of hardware circuit design and software compilation is verified by experiments, and the automatic frequency tracking effect is observed. The feasibility of the method proposed in this paper is verified based on the analysis of experimental data.
- 25 May 2022
- Published by Springer Nature
- p. 47-54
Influence of Horizontal Inertial Loads on the Operation of Overhead Crane Girders
- 25 May 2022
- Published by Springer Nature
- p. 47-54
Influence of Horizontal Inertial Loads on the Operation of Overhead Crane Girders