Lixin Shen
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Lixin Shen has a total of 12 co-authors. Here are the top co-authors by number of shared publications:
Shining Chan
3 shared publications- Fei Xing
School of Aerospace Engineering, Xiamen University , Xiamen 361102
2 shared publications Gangyi Fang
2 shared publicationsLa Qin
School of Aerospace Engineering, Xiamen University, Xiamen, Fujian Province, China, 361102
2 shared publications- Chaohu Jiang1 shared publication
Fei Xing
1 shared publication
Latest Publications
- 1 January 2026
- Published by AIP Publishing in Physics of Fluids
- Vol. 38 (1)
Numerical study of the effect of the initial velocity fluctuations of a rotating conical liquid sheet on secondary atomization
To investigate the influence of initial instability waves on the secondary atomization of a rotating conical liquid sheet, this study adopted a numerical simulation method. By varying the initial velocity of the liquid sheet to simulate the initial instability waves, the effects of sinusoidal fluctuating velocities under different frequencies and amplitudes on secondary atomization were investigated. The research demonstrates that the characteristic parameters of secondary atomization undergo regular changes with increases in the frequency and amplitude of the initial velocity fluctuations of the liquid sheet. Furthermore, the direction of these changes (increase or decrease) periodically reverses depending on the axial position or the moment of observation. The initial velocity fluctuations of the liquid sheet form ring-shaped droplet-dense regions along the axis of the spray field. Variations in frequency and amplitude lead to changes in the droplet number distribution within each droplet-dense region, as well as alterations in the droplet distribution on the inner and outer sides of the spray cone in the radial direction. In addition, the influence of the velocity fluctuation frequency on the secondary atomization characteristics and the spatial distribution characteristics of the droplets is significantly greater than that of the amplitude. This study provides insights for regulating the droplet size and spatial distribution characteristics of the spray field, contributing to reliable prediction and control methods for the design of high-performance advanced combustion chamber nozzles.
- 1 January 2026
- Published by AIP Publishing in Physics of Fluids
- Vol. 38 (1)
Numerical study of the effect of the initial velocity fluctuations of a rotating conical liquid sheet on secondary atomization
To investigate the influence of initial instability waves on the secondary atomization of a rotating conical liquid sheet, this study adopted a numerical simulation method. By varying the initial velocity of the liquid sheet to simulate the initial instability waves, the effects of sinusoidal fluctuating velocities under different frequencies and amplitudes on secondary atomization were investigated. The research demonstrates that the characteristic parameters of secondary atomization undergo regular changes with increases in the frequency and amplitude of the initial velocity fluctuations of the liquid sheet. Furthermore, the direction of these changes (increase or decrease) periodically reverses depending on the axial position or the moment of observation. The initial velocity fluctuations of the liquid sheet form ring-shaped droplet-dense regions along the axis of the spray field. Variations in frequency and amplitude lead to changes in the droplet number distribution within each droplet-dense region, as well as alterations in the droplet distribution on the inner and outer sides of the spray cone in the radial direction. In addition, the influence of the velocity fluctuation frequency on the secondary atomization characteristics and the spatial distribution characteristics of the droplets is significantly greater than that of the amplitude. This study provides insights for regulating the droplet size and spatial distribution characteristics of the spray field, contributing to reliable prediction and control methods for the design of high-performance advanced combustion chamber nozzles.
- 1 January 2022
- Published by Begell House Inc. Publishers in Atomization and Sprays
- Vol. 32 (9) , 57-78
NUMERICAL STUDY ON THE EFFECTS OF DUAL-LAYER LIQUID SHEETS MERGING ON PRIMARY BREAKUP IN DUAL-ORIFICE NOZZLES
Primary breakup during atomization is governed by complex mechanisms and is not well understood. Detailed numerical simulations using the volume-of-fluid method augmented with adaptive mesh refinement techniques were performed to study the formation and disintegration of liquid sheets produced from a dual-orifice pressure-swirl atomizer. The calculated atomization characteristics agree with the experimental results given a maximum relative error for the spray cone angle of 4.9% and maximum relative error for the Sauter mean diameter of 7.4%. For the five considered cases, changes in the pressure drop over a certain range do not affect the final spray angle size, but larger pressure drops will cause the liquid sheet to open faster while delaying the merger of the liquid sheets. The perturbation wave that causes the primary breakup of the dual-layer liquid sheets consists of two parts: the initial perturbation wave and the perturbation wave originating from the merger of the dual-layer liquid sheets, which dominates their primary breakup but whose generation is delayed by an increased pressure drop. The axial position when the disturbance wave first grows to its maximum amplitude matches well with the liquid sheet breakup length with a maximum error of 11.9%. Research on the merger of liquid sheets helps to further study the mechanisms of dual-layer liquid sheet primary breakup and guide the understanding of atomization in dual-orifice pressure-swirl atomizers.
- 1 January 2022
- Published by Begell House Inc. Publishers in Atomization and Sprays
- Vol. 32 (9) , 57-78
NUMERICAL STUDY ON THE EFFECTS OF DUAL-LAYER LIQUID SHEETS MERGING ON PRIMARY BREAKUP IN DUAL-ORIFICE NOZZLES
Primary breakup during atomization is governed by complex mechanisms and is not well understood. Detailed numerical simulations using the volume-of-fluid method augmented with adaptive mesh refinement techniques were performed to study the formation and disintegration of liquid sheets produced from a dual-orifice pressure-swirl atomizer. The calculated atomization characteristics agree with the experimental results given a maximum relative error for the spray cone angle of 4.9% and maximum relative error for the Sauter mean diameter of 7.4%. For the five considered cases, changes in the pressure drop over a certain range do not affect the final spray angle size, but larger pressure drops will cause the liquid sheet to open faster while delaying the merger of the liquid sheets. The perturbation wave that causes the primary breakup of the dual-layer liquid sheets consists of two parts: the initial perturbation wave and the perturbation wave originating from the merger of the dual-layer liquid sheets, which dominates their primary breakup but whose generation is delayed by an increased pressure drop. The axial position when the disturbance wave first grows to its maximum amplitude matches well with the liquid sheet breakup length with a maximum error of 11.9%. Research on the merger of liquid sheets helps to further study the mechanisms of dual-layer liquid sheet primary breakup and guide the understanding of atomization in dual-orifice pressure-swirl atomizers.
- 1 January 2022
- Published by AIP Publishing in Physics of Fluids
- Vol. 34 (1) , 017109
Numerical study of the effect of surface topography on atomization performance in geometrically sensitive areas of centrifugal nozzles
Integral three-dimensional printing of aeroengine fuel nozzles is an emerging trend. However, the large relative roughness of the internal flow paths created by this processing method is problematic. To study the influence of the rough surface morphology on atomization performance in geometrically sensitive areas of centrifugal nozzles, this paper describes numerical simulations of the atomization process of five nozzle models with rough orifice sections. The simulation framework considers a coupled internal and external flow in stages. The macroscopic morphology of the numerically calculated spray field is found to be consistent with experimental results, with maximum errors in the Sauter mean diameter, spray angle, and flow rate of just 8.7%, 3.7%, and 6.1%, respectively. The numerical results show that the nozzle's rough surface morphology in geometrically sensitive areas has a non-negligible impact on the liquid film velocity fluctuations, primary breakup, and secondary atomization characteristics. Indeed, the effect on primary breakup is large, with the maximum difference between the five rough-surface models reaching 22.9%. The effect on secondary atomization is small, with a maximum difference of just 5.7% except in the number of droplets, which has a maximum difference of 22.1%. Among the five rough-surface models, the atomization characteristics of the smooth model differ greatly from those of the real model, whereas a power-function model best reflects the real surface morphology. This study provides new ideas for nozzle performance prediction and optimization, and provides a reference for engineering applications of three-dimensional printed centrifugal nozzles.
- 1 January 2022
- Published by AIP Publishing in Physics of Fluids
- Vol. 34 (1) , 017109
Numerical study of the effect of surface topography on atomization performance in geometrically sensitive areas of centrifugal nozzles
Integral three-dimensional printing of aeroengine fuel nozzles is an emerging trend. However, the large relative roughness of the internal flow paths created by this processing method is problematic. To study the influence of the rough surface morphology on atomization performance in geometrically sensitive areas of centrifugal nozzles, this paper describes numerical simulations of the atomization process of five nozzle models with rough orifice sections. The simulation framework considers a coupled internal and external flow in stages. The macroscopic morphology of the numerically calculated spray field is found to be consistent with experimental results, with maximum errors in the Sauter mean diameter, spray angle, and flow rate of just 8.7%, 3.7%, and 6.1%, respectively. The numerical results show that the nozzle's rough surface morphology in geometrically sensitive areas has a non-negligible impact on the liquid film velocity fluctuations, primary breakup, and secondary atomization characteristics. Indeed, the effect on primary breakup is large, with the maximum difference between the five rough-surface models reaching 22.9%. The effect on secondary atomization is small, with a maximum difference of just 5.7% except in the number of droplets, which has a maximum difference of 22.1%. Among the five rough-surface models, the atomization characteristics of the smooth model differ greatly from those of the real model, whereas a power-function model best reflects the real surface morphology. This study provides new ideas for nozzle performance prediction and optimization, and provides a reference for engineering applications of three-dimensional printed centrifugal nozzles.