Dajung Hong
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Dajung Hong has a total of 21 co-authors. Here are the top co-authors by number of shared publications:
- Sanggyu Yim
Kookmin University
3 shared publications - Arya Ajeev
Materials Engineering And Nanosensor [MEAN] Laboratory, Department of Chemical and Biomedical Engineering, The University of Maine, Orono, USA
1 shared publication - Colton Duprey
Advanced Structures & Composites Center [ASCC] The University of Maine Orono Maine USA
1 shared publication - Dongju Kim
Department of Chemistry Korea Advanced Institute of Science and Technology (KAIST) Daejeon 34141 Republic of Korea
1 shared publication Emily Linn
Department of Chemical and Biological Engineering, The University of Alabama, Tuscaloosa, USA
1 shared publication- Evan K. Wujcik
Materials Engineering And Nanosensor [MEAN] Laboratory, Department of Chemical and Biomedical Engineering, The University of Maine, Orono, USA
1 shared publication
Latest Publications
- Open Access
- 5 September 2025
- Published by Springer Nature in Advanced Composites and Hybrid Materials
- Vol. 8 (5) , 1-19
A recyclable PANI/PAAMPSA nanocomposite with repeatable, rapid, autonomous self-healing, and unprecedented electro-mechanical properties
- 5 September 2025
- Published by Springer Nature in Advanced Composites and Hybrid Materials
- Vol. 8 (5) , 1-19
Open AccessA recyclable PANI/PAAMPSA nanocomposite with repeatable, rapid, autonomous self-healing, and unprecedented electro-mechanical properties
- 17 November 2021
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry A
- Vol. 9 (46) , 26172-26180
Monodisperse RuO 2 nanoparticles for highly transparent and rapidly responsive supercapacitor electrodes
Highly transparent energy storage devices have attracted attention owing to their applications in innovative electronics and displays. However, it is still challenging to fabricate devices with high optical transmittance (Tvis) and areal capacitance (CA) simultaneously, and the capacitance of an electrode with Tvis exceeding 95% has not been reported yet. Here we demonstrate a simple process for fabricating ruthenium oxide (RuO2) nanoparticle (NP)-based ultrathin film electrodes with a Tvis of 97.1% and CA of 0.85 mF cm−2. This high transparency and capacitance are achieved by the deposition of organic ligand-decorated, small (∼2 nm) RuO2 NPs followed by subsequent removal of the ligands. The optical transparency of the electrode can easily be controlled by changing the concentration of the RuO2 NP solution. Efficient contact with the electrolyte and metallic conductivity of the uniformly spread RuO2 NPs result in a significantly high capacitance retention of 81.2% at a scan rate of 1000 mV s−1, the highest reported value. The cycle stability is also considerably improved, and 93.5% of capacitance is retained after 5000 charge–discharge cycles. Furthermore, the monodisperse RuO2 NPs can be uniformly and thinly deposited using a simple spray-coating technique, indicating their applicability to large-area transparent devices.
- 17 November 2021
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry A
- Vol. 9 (46) , 26172-26180
Monodisperse RuO 2 nanoparticles for highly transparent and rapidly responsive supercapacitor electrodes
Highly transparent energy storage devices have attracted attention owing to their applications in innovative electronics and displays. However, it is still challenging to fabricate devices with high optical transmittance (Tvis) and areal capacitance (CA) simultaneously, and the capacitance of an electrode with Tvis exceeding 95% has not been reported yet. Here we demonstrate a simple process for fabricating ruthenium oxide (RuO2) nanoparticle (NP)-based ultrathin film electrodes with a Tvis of 97.1% and CA of 0.85 mF cm−2. This high transparency and capacitance are achieved by the deposition of organic ligand-decorated, small (∼2 nm) RuO2 NPs followed by subsequent removal of the ligands. The optical transparency of the electrode can easily be controlled by changing the concentration of the RuO2 NP solution. Efficient contact with the electrolyte and metallic conductivity of the uniformly spread RuO2 NPs result in a significantly high capacitance retention of 81.2% at a scan rate of 1000 mV s−1, the highest reported value. The cycle stability is also considerably improved, and 93.5% of capacitance is retained after 5000 charge–discharge cycles. Furthermore, the monodisperse RuO2 NPs can be uniformly and thinly deposited using a simple spray-coating technique, indicating their applicability to large-area transparent devices.
- Open Access
- 5 January 2012
- Published by Springer Nature in Discover Nano
- Vol. 7 (1) , 39
Effective surface oxidation of polymer replica molds for nanoimprint lithography
In nanoimprint lithography, a surface oxidation process is needed to produce an effective poly(dimethylsiloxane) coating that can be used as an anti-adhesive surface of template molds. However, the conventional photooxidation technique or acidic oxidative treatment cannot be easily applied to polymer molds with nanostructures since surface etching by UV radiation or strong acids significantly damages the surface nanostructures in a short space of time. In this study, we developed a basic oxidative treatment method and consequently, an effective generation of hydroxyl groups on a nanostructured surface of polymer replica molds. The surface morphologies and water contact angles of the polymer molds indicate that this new method is relatively nondestructive and more efficient than conventional oxidation treatments.
- 5 January 2012
- Published by Springer Nature in Discover Nano
- Vol. 7 (1) , 39
Open AccessEffective surface oxidation of polymer replica molds for nanoimprint lithography
In nanoimprint lithography, a surface oxidation process is needed to produce an effective poly(dimethylsiloxane) coating that can be used as an anti-adhesive surface of template molds. However, the conventional photooxidation technique or acidic oxidative treatment cannot be easily applied to polymer molds with nanostructures since surface etching by UV radiation or strong acids significantly damages the surface nanostructures in a short space of time. In this study, we developed a basic oxidative treatment method and consequently, an effective generation of hydroxyl groups on a nanostructured surface of polymer replica molds. The surface morphologies and water contact angles of the polymer molds indicate that this new method is relatively nondestructive and more efficient than conventional oxidation treatments.