Grecia Isis Moreno Grijalva
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Grecia Isis Moreno Grijalva has a total of 5 co-authors. Here are the top co-authors by number of shared publications:
- Arturo Zizumbo-López
Graduate and Research Center in Chemistry, Tecnológico Nacional de México/Tijuana Institute of Technology, Tijuana 22510, Baja California, Mexico
1 shared publication Juan Antonio Paz González
Facultad de Ciencias de la Ingeniería y Tecnología, Universidad Autónoma de Baja California. Unidad Valle de las Palmas, Tijuana, Baja California, México
1 shared publication- Manuel Alejandro Cardona Salcedo
Tecnológico Nacional de México/Instituto Tecnológico de Tijuana, Posgrado en Ciencias de la Ingeniería, Blvd. Industrial s/n col. Mesa de Otay, 22500, Tijuana, Baja California, México
1 shared publication Mercedes Teresita Oropeza Guzmán
Tecnológico Nacional de México/Instituto Tecnológico de Tijuana, Posgrado en Ciencias de la Ingeniería, Blvd. Industrial s/n col. Mesa de Otay, 22500, Tijuana, Baja California, México
1 shared publicationYadira Gochi Ponce
Tecnológico Nacional de México/Instituto Tecnológico de Tijuana, Posgrado en Ciencias de la Ingeniería, Blvd. Industrial s/n col. Mesa de Otay, 22500, Tijuana, Baja California, México
1 shared publication
Latest Publications
- Open Access
- 6 October 2021
- Published by Facultad de Ciencias de la Ingenieria y Tecnologia de la UABC in REVISTA DE CIENCIAS TECNOLÓGICAS
- Vol. 4 (4) , 388-398
Polylactic acid/multi walled carbon nanotubes (PLA/MWCNT) nanocomposite for 3D printing of medical devices
In recent years, the composite nanomaterials area has had a great development impact in health sciences. Biomaterials depict as one of the most promising since they are compatible with additive manufacturing (AM) techniques. It is also possible to use them to mold specific medical parts. Composite nanomaterials have shown good biocompatibility and low toxicity to have benefits equal to or greater than metals (i.e., Co-Cr alloy). The purpose of this study is to develop a nanocomposite biomaterial (PLA/MWCNTf) from Polylactic Acid (PLA) and functionalized Multi Walled Carbon Nanotubes (MWCNTf) to evidence its potential application in 3D printing of orthopedic fixation devices. PLA/MWCNTf nanocomposite was prepared by solution blending technique, incorporating a proportion of 0.5 wt% of MWCNTf to the PLA matrix. TGA analysis of the PLA/MWCNTf was used to determine the thermal stability, a slight increase was found compared to the PLA. FTIR spectroscopy confirmed the presence of carboxylic acid groups in the MWCNTf which improves good incorporation of the nanotubes in the PLA matrix. Additionally, Raman spectroscopy, SEM, and AFM micrographs were used to verify MWCNTf reached the PLA surface homogeneously. Additive manufacturing preparation was done by extrusion molding of PLA/MWCNTf as well as its 3D printing.
- 6 October 2021
- Published by Facultad de Ciencias de la Ingenieria y Tecnologia de la UABC in REVISTA DE CIENCIAS TECNOLÓGICAS
- Vol. 4 (4) , 388-398
Open AccessPolylactic acid/multi walled carbon nanotubes (PLA/MWCNT) nanocomposite for 3D printing of medical devices
In recent years, the composite nanomaterials area has had a great development impact in health sciences. Biomaterials depict as one of the most promising since they are compatible with additive manufacturing (AM) techniques. It is also possible to use them to mold specific medical parts. Composite nanomaterials have shown good biocompatibility and low toxicity to have benefits equal to or greater than metals (i.e., Co-Cr alloy). The purpose of this study is to develop a nanocomposite biomaterial (PLA/MWCNTf) from Polylactic Acid (PLA) and functionalized Multi Walled Carbon Nanotubes (MWCNTf) to evidence its potential application in 3D printing of orthopedic fixation devices. PLA/MWCNTf nanocomposite was prepared by solution blending technique, incorporating a proportion of 0.5 wt% of MWCNTf to the PLA matrix. TGA analysis of the PLA/MWCNTf was used to determine the thermal stability, a slight increase was found compared to the PLA. FTIR spectroscopy confirmed the presence of carboxylic acid groups in the MWCNTf which improves good incorporation of the nanotubes in the PLA matrix. Additionally, Raman spectroscopy, SEM, and AFM micrographs were used to verify MWCNTf reached the PLA surface homogeneously. Additive manufacturing preparation was done by extrusion molding of PLA/MWCNTf as well as its 3D printing.