Michael Heitzman
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Michael Heitzman has a total of 12 co-authors. Here are the top co-authors by number of shared publications:
- A. P. Wei Geng
Nanjing Forestry University
1 shared publication - Changfa Ai
College of Civil Engineering, Southwest Jiaotong University, Chengdu 610031, China
1 shared publication - Charles T. Jahren
Iowa State Univ
1 shared publication - Don Chen
Assistant Professor, Dept. of Engineering Technology and Construction Management, Univ. of North Carolina at Charlotte, Charlotte, NC 28223
1 shared publication - Fan Gu
National Center for Asphalt Technology, Auburn University, Auburn, AL, USA
1 shared publication - Gongyun Liao
School of Transportation
1 shared publication
Latest Publications
- 19 September 2022
- Published by Morressier GmbH
Using Shotblasting Treatment to Improve Asphalt Pavement Friction at the NCAT Test Track
The objective of this study was to examine the effectiveness of using shotblasting treatment to improve surface friction of asphalt pavements. Th |
- 19 September 2022
- Published by Morressier GmbH
Using Shotblasting Treatment to Improve Asphalt Pavement Friction at the NCAT Test Track
The objective of this study was to examine the effectiveness of using shotblasting treatment to improve surface friction of asphalt pavements. Th |
- 21 July 2016
- Published by American Society of Civil Engineers (ASCE)
- p. 109-116
Measuring the Thermal Properties of Pavement Materials
Thermal conductivity is an important material parameter that determines the thermal conditions in pavement and influences cracking, rutting, and fatigue. The test standard (ASTM C177) is not suitable for pavement samples. Research at Arizona State University has developed a test method that uses cylindrical samples to measure thermal conductivity. This paper proposes an improved and simplified ASU laboratory test procedure for measuring the thermal conductivity of pavement material using a cylindrical core sample, including a shorter core sample, a smaller hole drilled in the center, rubber retainers to place thermal couples on the outer face of the core and saturated sand to fill the voids in the inner hole. The test generally requires three hours to reach a steady state of heat flow. This test method is verified by more than 50 samples from four different locations across the United States.
- 21 July 2016
- Published by American Society of Civil Engineers (ASCE)
- p. 109-116
Measuring the Thermal Properties of Pavement Materials
Thermal conductivity is an important material parameter that determines the thermal conditions in pavement and influences cracking, rutting, and fatigue. The test standard (ASTM C177) is not suitable for pavement samples. Research at Arizona State University has developed a test method that uses cylindrical samples to measure thermal conductivity. This paper proposes an improved and simplified ASU laboratory test procedure for measuring the thermal conductivity of pavement material using a cylindrical core sample, including a shorter core sample, a smaller hole drilled in the center, rubber retainers to place thermal couples on the outer face of the core and saturated sand to fill the voids in the inner hole. The test generally requires three hours to reach a steady state of heat flow. This test method is verified by more than 50 samples from four different locations across the United States.
- 19 October 2015
- Published by American Society of Civil Engineers (ASCE)
- p. 219-232
Temperature Effects on the Correlations between Tire-Pavement Noises and Pavement Surface Characteristics
The correlations between tire-pavement noises and pavement surface characteristics have been investigated for many decades, but temperature effects on these correlations are not clear yet. The objective of this paper was to investigate temperature effects on correlations between noise levels and surface characteristics correlations. Tire-pavement noises were measured quarterly by on-board sound intensity (OBSI) method on four types of asphalt pavements on the 2009 National Center for Asphalt Technology (NCAT) test track. Air and pavement temperatures were also recorded during those noise measurements. Four pavement surface characteristics (texture, porosity, roughness, and stiffness) were correlated with noise levels using a linear regression method. Temperature effects were established by comparing correlation coefficients between noise levels and surface characteristics with/without temperature correction. The results showed that, air temperature influenced the correlations between noise levels and surface textures, and temperature corrections were necessary to be taken before analysis. It would be benefit to data processing during tire-pavement noise research.
- 19 October 2015
- Published by American Society of Civil Engineers (ASCE)
- p. 219-232
Temperature Effects on the Correlations between Tire-Pavement Noises and Pavement Surface Characteristics
The correlations between tire-pavement noises and pavement surface characteristics have been investigated for many decades, but temperature effects on these correlations are not clear yet. The objective of this paper was to investigate temperature effects on correlations between noise levels and surface characteristics correlations. Tire-pavement noises were measured quarterly by on-board sound intensity (OBSI) method on four types of asphalt pavements on the 2009 National Center for Asphalt Technology (NCAT) test track. Air and pavement temperatures were also recorded during those noise measurements. Four pavement surface characteristics (texture, porosity, roughness, and stiffness) were correlated with noise levels using a linear regression method. Temperature effects were established by comparing correlation coefficients between noise levels and surface characteristics with/without temperature correction. The results showed that, air temperature influenced the correlations between noise levels and surface textures, and temperature corrections were necessary to be taken before analysis. It would be benefit to data processing during tire-pavement noise research.
- 1 June 2010
- Published by American Society of Civil Engineers (ASCE) in Journal of Performance of Constructed Facilities
- Vol. 24 (3) , 265-274
Long-Term Field Performance of Cold In-Place Recycled Roads in Iowa
Cold in-place recycling (CIR) is one of the most effective methods to rehabilitate asphalt pavements. In fact, most CIR roads have performed well at low cost in Iowa since the first CIR road was constructed in 1986. However, some CIR roads have reached failures earlier than their expected design lives because there is no design standard for designing CIR roads with a limited amount of past performance information. Some of the most prominent problems seemed to have come from selecting CIR in areas where there are poor subgrades. Therefore, it is critical to collect CIR performance data along with falling weight deflectometer (FWD) data in order to develop performance models. The main purpose of this paper is to document that effort. The performance models were developed on the basis of historical data collected from CIR roads in Iowa. First, an inventory of CIR roads was created which includes construction information, subgrade and base characteristics, and traffic levels. In consideration of pavement age,...
- 1 June 2010
- Published by American Society of Civil Engineers (ASCE) in Journal of Performance of Constructed Facilities
- Vol. 24 (3) , 265-274
Long-Term Field Performance of Cold In-Place Recycled Roads in Iowa
Cold in-place recycling (CIR) is one of the most effective methods to rehabilitate asphalt pavements. In fact, most CIR roads have performed well at low cost in Iowa since the first CIR road was constructed in 1986. However, some CIR roads have reached failures earlier than their expected design lives because there is no design standard for designing CIR roads with a limited amount of past performance information. Some of the most prominent problems seemed to have come from selecting CIR in areas where there are poor subgrades. Therefore, it is critical to collect CIR performance data along with falling weight deflectometer (FWD) data in order to develop performance models. The main purpose of this paper is to document that effort. The performance models were developed on the basis of historical data collected from CIR roads in Iowa. First, an inventory of CIR roads was created which includes construction information, subgrade and base characteristics, and traffic levels. In consideration of pavement age,...