Caiyou Zeng
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Caiyou Zeng has a total of 65 co-authors. Here are the top co-authors by number of shared publications:
Baoqiang Cong
15 shared publicationsBojin Qi
8 shared publications- Zihao Jiang6 shared publications
- Yuan Zhao4 shared publications
Zijin Chang
4 shared publicationsYingyu Cao
3 shared publications
Latest Publications
- 8 April 2026
- Published by Wiley in Steel Research International
Effect of Interlayer Cooling Strategies on the Microstructure and Mechanical Properties of DED‐Fabricated 308L Stainless Steel Deposited on 304L Substrate
The issue of thermal accumulation in directed energy deposition (DED) leads to grain coarsening, microstructural inhomogeneity, and deterioration of mechanical properties, which severely restricts the quality of large‐scale components. Therefore, effectively controlling interlayer temperature and mitigating heat accumulation have become critical challenges in optimizing the manufacturing quality of DED. In this study, the effects of interlayer active cooling on the microstructure and mechanical properties of DED‐fabricated 304L stainless steel were investigated. Three cooling strategies were comparatively examined: natural air cooling (A1), forced air cooling (A2), and substrate water‐based cooling (W1). Microstructural features were characterized using optical microscopy, scanning electron microscopy (SEM), and electron backscatter diffraction. Mechanical behavior was evaluated through tensile testing and fracture surface observation by SEM. The results revealed that active cooling (A2 and W1) significantly reduced interlayer cooling time, improved macroscopic morphology, minimized melt pool overflow, and enhanced the consistency of layer height and width. Compared with natural cooling, forced air cooling reduced the interlayer cooling time by ≈35–45%, refined the average grain size from ∼ 42 µm to ∼ 26 µm, and limited interlayer ultimate tensile strength (UTS) variation to ≤8% (≈682–688 MPa). Water‐based cooling further reduced grain size (∼22 µm) but induced pronounced strength anisotropy, with bottom‐layer UTS decreasing by ∼33% relative to natural cooling. The mechanical properties of water‐based cooling specimens exhibited pronounced nonuniformity along the build height: the middle layers showed the highest ultimate tensile strength, whereas the bottom layers displayed relatively low strength, primarily due to the development of strong textured columnar grains induced by a high temperature gradient‐to‐cooling rate ratio. Forced air cooling achieved the best uniformity of mechanical properties, demonstrating greater effectiveness in suppressing thermal accumulation and balancing the strength–ductility trade‐off throughout the component.
- 8 April 2026
- Published by Wiley in Steel Research International
Effect of Interlayer Cooling Strategies on the Microstructure and Mechanical Properties of DED‐Fabricated 308L Stainless Steel Deposited on 304L Substrate
The issue of thermal accumulation in directed energy deposition (DED) leads to grain coarsening, microstructural inhomogeneity, and deterioration of mechanical properties, which severely restricts the quality of large‐scale components. Therefore, effectively controlling interlayer temperature and mitigating heat accumulation have become critical challenges in optimizing the manufacturing quality of DED. In this study, the effects of interlayer active cooling on the microstructure and mechanical properties of DED‐fabricated 304L stainless steel were investigated. Three cooling strategies were comparatively examined: natural air cooling (A1), forced air cooling (A2), and substrate water‐based cooling (W1). Microstructural features were characterized using optical microscopy, scanning electron microscopy (SEM), and electron backscatter diffraction. Mechanical behavior was evaluated through tensile testing and fracture surface observation by SEM. The results revealed that active cooling (A2 and W1) significantly reduced interlayer cooling time, improved macroscopic morphology, minimized melt pool overflow, and enhanced the consistency of layer height and width. Compared with natural cooling, forced air cooling reduced the interlayer cooling time by ≈35–45%, refined the average grain size from ∼ 42 µm to ∼ 26 µm, and limited interlayer ultimate tensile strength (UTS) variation to ≤8% (≈682–688 MPa). Water‐based cooling further reduced grain size (∼22 µm) but induced pronounced strength anisotropy, with bottom‐layer UTS decreasing by ∼33% relative to natural cooling. The mechanical properties of water‐based cooling specimens exhibited pronounced nonuniformity along the build height: the middle layers showed the highest ultimate tensile strength, whereas the bottom layers displayed relatively low strength, primarily due to the development of strong textured columnar grains induced by a high temperature gradient‐to‐cooling rate ratio. Forced air cooling achieved the best uniformity of mechanical properties, demonstrating greater effectiveness in suppressing thermal accumulation and balancing the strength–ductility trade‐off throughout the component.
- Top Cited PapersOpen Access
- 1 March 2026
- Published by KEAI Publishing in Journal of Magnesium and Alloys
- Vol. 16, 101929
The role of in-situ phase transformation behavior on mechanical heterogeneity in Mg-7Gd-3Y-1Zn-0.5Zr alloy fabricated by wire-arc additive manufacturing
- 1 March 2026
- Published by KEAI Publishing in Journal of Magnesium and Alloys
- Vol. 16, 101929
Top Cited PapersOpen AccessThe role of in-situ phase transformation behavior on mechanical heterogeneity in Mg-7Gd-3Y-1Zn-0.5Zr alloy fabricated by wire-arc additive manufacturing
- Top Cited PapersOpen Access
- 1 November 2025
- Published by KEAI Publishing in Journal of Magnesium and Alloys
- Vol. 13 (11) , 5571-5588
Synergistic optimization of efficiency-microstructure-performance in wire-arc additive manufacturing of AZ31 magnesium alloy
- 1 November 2025
- Published by KEAI Publishing in Journal of Magnesium and Alloys
- Vol. 13 (11) , 5571-5588
Top Cited PapersOpen AccessSynergistic optimization of efficiency-microstructure-performance in wire-arc additive manufacturing of AZ31 magnesium alloy
- Open Access
- 25 October 2025
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 39, 4996-5007
Achieving high-integrity seals in double-layered 316L nuclear waste containers through ultrasonic-frequency pulsed arc deep penetration welding
- 25 October 2025
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 39, 4996-5007
Open AccessAchieving high-integrity seals in double-layered 316L nuclear waste containers through ultrasonic-frequency pulsed arc deep penetration welding
- Open Access
- 18 August 2025
- Published by Elsevier in Chinese Journal of Aeronautics
- Vol. 39 (9)
Developing a machine vision framework for real-time monitoring dynamic molten pool during aluminum alloy TIG welding
- 18 August 2025
- Published by Elsevier in Chinese Journal of Aeronautics
- Vol. 39 (9)
Open AccessDeveloping a machine vision framework for real-time monitoring dynamic molten pool during aluminum alloy TIG welding
- 10 March 2025
- Published by Elsevier in Journal of Alloys and Compounds
- Vol. 1021
Improved thermal and mechanical performances of additively remanufactured Invar alloy via ultrasonic-frequency pulse arc
- 10 March 2025
- Published by Elsevier in Journal of Alloys and Compounds
- Vol. 1021
Improved thermal and mechanical performances of additively remanufactured Invar alloy via ultrasonic-frequency pulse arc
- Open Access
- 22 November 2024
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 33, 9166-9179
Microstructural evolution and mechanical property of high-strength metastable β titanium alloy joint via electron beam welding
- 22 November 2024
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 33, 9166-9179
Open AccessMicrostructural evolution and mechanical property of high-strength metastable β titanium alloy joint via electron beam welding