Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Alis Ekmekci has a total of 33 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Experimental study of wind energy harvesting from flow-induced vibration of a cantilevered circular cylinder with a rigid plate

    by Mohamed Heragy, Takahiro Kiwata, Haruki Mitani, Takaaki Kono, Takuma Shima, Kita Shota, Alis Ekmekci

  • Aeroacoustic Study of a Generic Nose Landing Gear Focusing on Steering Mechanism

    by Zhe Lu, Alis Ekmekci

    This study investigates the far-field aeroacoustic characteristics of a 30%-scale generic nose landing gear model, with particular emphasis on the influence of the steering mechanism. Phased-microphone array measurements were conducted in both the sideline and flyover directions for various configurations involving the strut, wheels, and two types of steering mechanisms. Results show that the bracket-type steering mechanism generates substantially higher noise levels than the integrated type, emerging as a major noise source above 3–4 kHz. Nevertheless, given its widespread use in commercial aircraft, the bracket steering mechanism is examined in greater detail. Its noise levels follow a rise-and-fall trend as the angle of the actuator cylinders in the steering mechanism increases from 0 to 90 deg relative to the streamwise direction, a behavior observed for both upstream and downstream placements of the mechanism relative to the strut. The acoustic signature of the bracket mechanism has a multipeak feature, with its overall shape following Strouhal-number-based scaling with the flow velocity to the sixth power, a feature attributable to vortex shedding from the bracket plates. From the noise localization maps, the major noise sources are identified to be on the bracket structure, while the actuators contribute negligible noise in comparison.

  • Open Access

    Experimental study of wind energy harvesting from Flow-Induced Vibration of a Cantilevered Circular Cylinder with a Rigid Plate

    by Mohamed Heragy, Takahiro Kiwata, Haruki Mitani, Takaaki Kono, Takuma Shima, Shota Kita, Alis Ekmekci

    This study investigates the impact of an attached/detached rigid splitter plate on the performance of a magnetostrictive energy harvester of a cantilevered circular cylinder using wind tunnel experiments. Three configurations are analysed: cylinders with an attached plate of variable width show increased lock-in range as width increases up to cylinder diameter. For large-detached plates, pure vortex-induced vibrations occur with wider gaps greater than cylinder diameter, while narrower gaps affecting the incident flow angle and causing fluid mechanical interference between shear layers, which generate a local inner circulatory flow led to galloping. Small-detached plates exhibit performance similar to large ones. The optimal splitter plate size for energy harvesting includes a length approximately equal to the cylinder length, a width three times cylinder diameter, and a gap smaller than half the cylinder diameter, yielding significant power generation of about 0.74 mW. Optimized splitter plates can serve as tail vanes in variable wind conditions to enhance energy capture.

  • Open Access

    Experimental study of wind energy harvesting from Flow-Induced Vibration of a Cantilevered Circular Cylinder with a Rigid Plate

    by Mohamed Heragy, Takahiro Kiwata, Haruki Mitani, Takaaki Kono, Takuma Shima, Shota Kita, Alis Ekmekci

    This study investigates the impact of an attached/detached rigid splitter plate on the performance of a magnetostrictive energy harvester of a cantilevered circular cylinder using wind tunnel experiments. Three configurations are analysed: cylinders with an attached plate of variable width show increased lock-in range as width increases up to cylinder diameter. For large-detached plates, pure vortex-induced vibrations occur with wider gaps greater than cylinder diameter, while narrower gaps affecting the incident flow angle and causing fluid mechanical interference between shear layers, which generate a local inner circulatory flow led to galloping. Small-detached plates exhibit performance similar to large ones. The optimal splitter plate size for energy harvesting includes a length approximately equal to the cylinder length, a width three times cylinder diameter, and a gap smaller than half the cylinder diameter, yielding significant power generation of about 0.74 mW. Optimized splitter plates can serve as tail vanes in variable wind conditions to enhance energy capture.

  • Aeroacoustic Study of a Generic Nose Landing Gear Focusing on the Torque Link

    by Zhe Lu, Alis Ekmekci

    Far-field aeroacoustic measurements were conducted on a 30%-scale generic nose landing gear model, using a phased microphone array. Nine model configurations were tested, created from different combinations of strut, wheels (with or without cavities), and torque link. For configurations equipped with the torque link, its placement upstream or downstream of the strut and different separation angles between its arms ([ ], 119, and 133 deg) were considered. Both spectral results and noise localization maps were examined. At [ ], the torque link upstream of the strut produced higher noise levels than the downstream one. At [ ], this trend reversed, making the upstream torque link case the quietest in both the sideline and flyover directions. Although this low-noise advantage of the upstream torque link at [ ] disappears when wheels have no cavities, with the inclusion of inner and outer cavities on wheels, the upstream torque link regains its noise advantage, suggesting favorable interactions between the wheel cavities and the upstream torque link. Given that real-life landing gears have [ ] around 133 deg and wheels with cavities, these findings suggest that positioning the torque link upstream in aircraft has the potential to reduce noise.


  • Vortex shedding from a yaw-oscillating circular cylinder in subcritical flow

    by V. Nasr Esfahani, R. Hanson, A. Ekmekci

    This study investigates vortex shedding characteristics from a circular cylinder subjected to yaw oscillations. The study considers two length-to-diameter ratios (13 and 20) and two Reynolds numbers (5×103 and 1.5×104). Yaw oscillations ranging from θ=0° to 30° are considered at various reduced frequencies from 0.25 to 4. Vortex shedding behavior at the mid-span of the cylinder is measured using hot-wire anemometry. Planar particle image velocimetry (PIV) measurements at the mid-span are used to visualize the near wake. It is shown that an increase in the reduced frequency leads to a shift in the frequency range of vortex shedding toward lower values. Vortices are shed nearer to the base of the cylinder, and vortex shedding becomes more disorganized with increasing reduced frequency. Based on phase-averaged analysis of vortex shedding, the validity of the independence principle (IP) diminishes during the first half cycle beyond θ=15° at low reduced frequencies and beyond θ=20° at moderate reduced frequencies. In the return cycle, the deviation from the IP increases with increasing reduced frequency. The IP prediction is re-established at low yaw angles during the return cycle and for low reduced frequencies. Increasing the length-to-diameter ratio enhanced the organized vortex shedding and elevated the shedding frequency for both static and yaw-oscillating cylinders.


  • Open Access

    The effect of end conditions on the body motion and near-wake flow structure of a circular cylinder under vortex-induced vibration

    by Pouya Mohtat, Alis Ekmekci

    Free transverse oscillations of an elastically mounted circular cylinder with low mass-damping are studied with a focus on the effects of the cylinder end condition on structural oscillations and vortex shedding. While the top end of the cylinder pierces the free surface of a water channel, the lower end is changed to have three end conditions: an attached endplate, an endplate unattached from the cylinder at varying gaps and no endplate. All three response branches are examined, with the reduced velocity sweeping $2 \le {U^\ast } \le 15$ (corresponding to a Reynolds number range of $2000 \le Re \le 14\;700$ ). Although the cylinder oscillations are unaffected by the end condition in the initial and upper branches, they show significant dependency on the end condition in the lower branch. When the endplate is attached or unattached with a small gap, the upper-to-lower branch transition occurs with a sudden decrease in oscillation amplitude, after which the lower branch maintains a near-constant amplitude. For larger gaps or no endplate, with increasing reduced velocity, the oscillation amplitude decreases gradually from its peak without any discernible sign of transition between the upper and lower branches. The three-dimensional effects of the gap are the basis for these differences in oscillation. Atop the strong tip vortex, a low-magnitude streamwise velocity region develops downstream of the cylinder, which delays upper-to-lower branch transition over the cylinder span that sees this low-velocity region. With increasing gap, this low-velocity region and the delay in transition spread over larger spanwise extents, forcing the overall body to oscillate at larger amplitudes.


  • Open Access

    Design and characterization of the university of Toronto hybrid anechoic wind tunnel

    by M.K. Okoronkwo, R. Alsaif, R. Haklander, S. Baba, J.M. Eburn, Z. Lu, N. Arafa, O. Stalnov, A. Ekmekci, P. Lavoie


  • Open Access

    Multiphysics Modeling of a Synthetic Jet Actuator in Operation

    by Matthew G. M. Butler, Alis Ekmekci, Pierre E. Sullivan

    Active flow control is a promising technology for reducing noise, emissions, and power consumption in various applications. To better understand the performance of synthetic jet actuators, a computational model that couples structural mechanics with electrostatics, pressure acoustics, and fluid dynamics is needed. The model presented here was validated against experimental data and then used to investigate the fluid behavior inside and outside the synthetic jet actuator cavity, the impacts of thermoviscous losses on capturing the acoustic response of the actuator, and the viability of different modeling methods of diaphragms in computational simulations. The results capture the feedback from the fluid onto the diaphragm and highlight the need for careful acoustic modeling.


  • Noise and Jet Momentum of Synthetic Jet Actuators with Different Orifice Configurations

    by Nadim Arafa, Pierre Sullivan, Alis Ekmekci

    Sound pressure levels and flow characteristics of a synthetic jet actuator (SJA) are investigated experimentally using the following orifice configurations: a) a slender rectangular slot orifice and b) an array of circular orifices with two different orifice diameters. All configurations have similar total orifice neck area, orifice height, and cavity volume, resulting in a similar Helmholtz frequency. Experiments are conducted for orifices mounted on a flat plate under a quiescent condition. The mean jet velocity exhibits resonant peaks at several excitation frequencies, which also gave rise to the sound pressure levels. The resonant frequencies and peak jet velocities were found to depend on the excitation amplitude and orifice configuration. Investigation of the jet momentum penetration into the quiescent air above the different orifice configurations shows that the momentum issuing from the rectangular slot decays much quicker than that of the circular orifices, irrespective of whether the SJA is excited at resonance or not. The most favorable performance (i.e., the highest momentum in the jet core) was obtained with the array of circular orifices having a smaller orifice diameter, even at off-resonance excitations. The work herein shows the possibility of reducing the SJA noise by 8–10 dB by operating the SJA at a frequency away from the Helmholtz frequency while still achieving comparable levels of jet momentum penetration into the crossflow.