JKJulian Klemens

Julian Klemens

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Julian Klemens has a total of 43 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    From Powder to Pouch Cell: Setting up a Sodium-Ion Battery Reference System Based on Na3V2(PO4)3/C and Hard Carbon

    by Pirmin Stüble, Cedric Müller, Nicole Bohn, Marcus Müller, Andreas Hofmann, Tolga Akçay, Julian Klemens, Arnd Koeppe, Satish Kolli, Deepalaxmi Rajagopal, et al.

    At the research level, novel active materials for batteries are synthesised on a small scale, fabricated into electrodes and electrochemically characterised using each group’s established process due to the lack of standards. Recently, eminent researchers have criticised the implementation of e.g. low active material contents/electrode loadings, the use of research-type battery cell constructions, or the lack of statistically relevant data, resulting in overstated data and thus giving misleading predictions of the key performance indicators of new battery technologies. Here, we report on the establishment of a reference system for the development of sodium-ion batteries. Electrodes are fabricated under relevant conditions using 9.5 mg/cm² self-synthesised Na3V2(PO4)3/C cathode active material and 3.6 mg/cm² commercially available hard carbon anode active material. It is found that different types of battery cells are more or less suitable for half- and/ or full-cell testing, resulting in ir/reproducible or underestimated active material capacities. Furthermore, the influence of electrode overhang, which is relevant for upscaling, is evaluated. The demonstrator cell (TRL 4-5) has been further characterised providing measured data on the power/energy density and thermal behaviour during rate testing up to 15 C and projections are made for its practical limits.


  • Open Access

    Using Hierarchically Structured, Nanoporous Particles as Building Blocks for NCM111 Cathodes

    by Werner Bauer, Marcus Müller, Luca Schneider, Marcel Häringer, Nicole Bohn, Joachim R. Binder, Julian Klemens, Philip Scharfer, Wilhelm Schabel, Helmut Ehrenberg

    Nanoparticles have many advantages as active materials, such as a short diffusion length, low charge transfer resistance, or a reduced probability of cracking. However, their low packing density makes them unsuitable for commercial battery applications. Hierarchically structured microparticles are synthesized from nanoscale primary particles by targeted aggregation. Due to their open accessible porosity, they retain the advantages of nanomaterials but can be packed much more densely. However, the intrinsic porosity of the secondary particles leads to limitations in processing properties and increases the overall porosity of the electrode, which must be balanced against the improved rate stability and increased lifetime. This is demonstrated for an established cathode material for lithium-ion batteries (LiNi0.33Co0.33Mn0.33O2, NCM111). For active materials with low electrical or ionic conductivity, especially post-lithium systems, hierarchically structured particles are often the only way to produce competitive electrodes.


  • Open Access

    Enabling Long‐term Cycling Stability of Na3V2(PO4)3/C vs. Hard Carbon Full‐cells

    by Pirmin Stüble, Cedric Müller, Julian Klemens, Philip Scharfer, Wilhelm Schabel, Marcel Häringer, Joachim R. Binder, Andreas Hofmann, Anna Smith

    Sodium‐ion batteries are becoming an increasingly important complement to lithium‐ion batteries. However, while extensive knowledge on the preparation of Li‐ion batteries with excellent cycling behavior exists, studies on applicable long‐lasting sodium‐ion batteries are still limited. Therefore, this study focuses on the cycling stability of batteries composed of Na3V2(PO4)3/C based cathodes and hard carbon anodes. It is shown that full‐cells with a decent stability are obtained for ethylene carbonate/propylene carbonate electrolyte and the conducting salt NaPF6. With cathode loadings of 1.2 mAh/cm2, after cell formation discharge capacities up to 92.6 mAh/g are obtained, and capacity retentions >90 % over 1000 charge/discharge cycles at 0.5 C/0.5 C are observed. It is shown that both, the additive fluoroethylene carbonate and impurities in the electrolyte, negatively affect the overall discharge capacity and cycling stability and should therefore be avoided. Remarkably, the internal resistances of well‐balanced and well‐built cells did not increase over 1500 cycles and 5 months of testing, which is a very promising result regarding the possible lifespan of the cells. The initial loss of active sodium ions in hard carbon remains a major problem, which can only be partially reduced by proper balancing.


  • Open Access

    Influences on Reliable Capacity Measurements of Hard Carbon in Highly Loaded Electrodes

    by Cedric Müller, Zhengqi Wang, Andreas Hofmann, Pirmin Stüble, Xinyang Liu‐Théato, Julian Klemens, Anna Smith

    For the development of a full‐cell battery system, typically appropriate cathodes and anodes are characterized within a half‐cell setup where a metal counter electrode is installed to gather data about the employed electrodes. Ultimately, the individual capacity loadings allow for suitable balancing of the anode to cathode capacity in the full‐cell. This approach seems rather unproblematic for lithium‐ion batteries. For sodium‐ion batteries, however, we show that the high reactivity of sodium metal strongly influences hard carbon‐based electrode measurements within sodium‐ion half‐cells. As hard carbon is considered state‐of‐the‐art anode material, the presented results have high impact on the development of sodium ion batteries. Specifically, we show that the type of electrolyte, as well as cell‐ and measurement‐setup are key factors for reliable sodium half‐cell measurements of hard carbon. The investigated hard carbon electrodes have a high active material loading of 7.2 mg/cm2 (with 93 % active material content) resulting in an areal capacity of 2.4 mAh/cm2, which represent application‐relevant conditions.


  • Open Access

    Challenges and Opportunities for Large‐Scale Electrode Processing for Sodium‐Ion and Lithium‐Ion Battery

    by Julian Klemens, Ann‐Kathrin Wurba, David Burger, Marcus Müller, Werner Bauer, Sebastian Büchele, Olatz Leonet, J. Alberto Blázquez, Iker Boyano, Elixabete Ayerbe, et al.

    Sodium‐ion batteries are an emerging technology that is still at an early stage of development. The electrode processing for anode and cathode is expected to be similar to lithium‐ion batteries (drop‐in technology), yet a detailed comparison is not published. There are ongoing questions about the influence of the active materials on processing parameters such as slurry viscosity, coating thicknesses, drying times, and behavior during fast drying. Herein, the expected drying time for the same areal capacity of anodes (graphite vs. hard carbon) and cathodes (lithium iron phosphate vs. Prussian blue analogs) are compared based on respective specific capacities reported in the literature. Estimates are made for the materials’ impact on production speed or dryer length. Within the experimental part, water‐based slurries of the same composition are mixed using different active materials according to identical procedure and the viscosity is compared. When drying at a constant drying rate (0.75 g m−2 s−1), lithium iron phosphate electrodes with different areal capacities (1–3 mAh cm−2) are shown to have the highest adhesion. For high drying rates (3 g m−2 s−1) at constant areal capacity, especially the investigated electrodes based on hard carbon show that no binder migration occurs.


  • Open Access

    Enabling Long-term Cycling Stability of Na3V2(PO4)3/C vs. Hard Carbon Full-cells

    by Pirmin Stüble, Cedric Müller, Julian Klemens, Philip Scharfer, Wilhelm Schabel, Marcel Häringer, Joachim R. Binder, Andreas Hofmann, Anna Smith

    Sodium-ion batteries are becoming an increasingly important complement to lithium-ion batteries. However, while extensive knowledge on the preparation of Li-ion batteries with excellent cycling behavior exists, studies on applicable long-lasting sodium-ion batteries are still limited. Therefore, this study focuses on the cycling stability of batteries composed of Na3V2(PO4)3/C based cathodes and hard carbon anodes. It is shown that full cells with a decent stability are obtained for ethylene carbonate / propylene carbonate electrolyte and the conducting salt NaPF6. With cathode loadings of 1.2 mAh/cm², after cell formation discharge capacities up to 92.6 mAh/g are obtained, and capacity retentions > 90 % over 1000 charge / discharge cycles at 0.5 C / 0.5 C are observed. It is shown that both, the additive fluoroethylene carbonate and traces of water in the cell, negatively affect the overall discharge capacity and cycling stability and should therefore be avoided. Remarkably, the internal resistances of well-balanced and wellbuilt cells did not increase over 1500 cycles and 5 months of testing, which is a very promising result regarding the possible lifespan of the cells. The initial loss of active sodium in hard carbon remains a major problem, which can only be partially reduced by proper balancing.


  • Open Access

    Drying of Compact and Porous NCM Cathode Electrodes in Different Multilayer Architectures: Influence of Layer Configuration and Drying Rate on Electrode Properties

    by Julian Klemens, David Burger, Luca Schneider, Sandro Spiegel, Marcus Müller, Nicole Bohn, Werner Bauer, Helmut Ehrenberg, Philip Scharfer, Wilhelm Schabel

    Porous, nanostructured particles ensure the wetting of electrolyte up to the particle core and shortened diffusion paths, which is relevant not only for lithium‐ion batteries but also for postlithium systems like sodium‐ion batteries. The porous structure leads to a high C‐rate capability. However, compared to conventional compact NCM, porous NCM shows a reduced adhesion force but no or only slight negative influence on C‐rate capability by binder migration at higher drying rates. Herein, a multilayer concept is used to increase the adhesion force with equal or better electrochemical performance compared to single‐layer electrodes. Compact particles of high volumetric energy density and porous particles with high C‐rate capability are combined in a simultaneously coated multilayer electrode. Multilayers with compact NCM toward the current collector and porous NCM with reduced binder content toward the separator side show an about 16‐times higher adhesion force at lower drying rate and an about ten‐times higher adhesion force at increased drying rate compared to electrodes produced of porous NCM only. The specific discharge capacity of the multilayers is increased by 88% at the lower and 67% at the higher drying rate for a discharge rate of 3C compared to a single layer with compact NCM.


  • Open Access

    Process and Drying Behavior Toward Higher Drying Rates of Hard Carbon Anodes for Sodium‐Ion Batteries with Different Particle Sizes: An Experimental Study in Comparison to Graphite for Lithium‐Ion‐Batteries

    by Julian Klemens, Luca Schneider, David Burger, Nadine Zimmerer, Marcus Müller, Werner Bauer, Helmut Ehrenberg, Philip Scharfer, Wilhelm Schabel

    Sodium‐ion batteries are considered to be one of the most promising postlithium batteries on the verge of commercialization. The electrode processing is expected to be similar to lithium‐ion batteries. However, the producibility and material processing challenges of potential electrode materials for anodes and cathodes are poorly understood. For industrial electrode production, a deep understanding of the processing of electrode materials with different particle morphologies is of great importance. In particular, the correlation between the process conditions and the electrode properties needs to be investigated further to understand the complex interactions between the battery slurry materials, the binder system, the drying process, and the microstructure formation. One promising anode material is hard carbon. The water‐based processing of hard carbon slurries presented in this article shows that the drying behavior is strongly interconnected with the particle size and particle interactions in the drying electrode. This study shows that all the hard carbons investigated do not exhibit binder migration at moderate drying rates. Even at very high drying rates (9 g m−2 s−1, 12 s drying time), an increase in adhesion force of up to 39% is observed for comparatively smaller particles compared to the adhesion force at lower drying rate.


  • Open Access

    Drying of NCM Cathode Electrodes with Porous, Nanostructured Particles Versus Compact Solid Particles: Comparative Study of Binder Migration as a Function of Drying Conditions

    by Julian Klemens, Luca Schneider, Eike Christian Herbst, Nicole Bohn, Marcus Müller, Werner Bauer, Philip Scharfer, Wilhelm Schabel

    Porous, nanostructured Li(NixCoyMn)O2 (NCM) achieves an improvement in the fast‐charging capability and the durability of lithium‐ion batteries. This improvement is attributed to an extended electrolyte—active material interface, where the electrochemical reactions take place and thus shorter diffusion paths inside the active material particles are necessary for charge transfer. Due to the porous particle morphology, new processing challenges arise compared to compact solid NCM. Herein, the properties of the slurries and the electrodes made of the two active materials and, in particular, the influence of the drying process on the binder distribution, are comparatively investigated. For the same composition of the slurries, a significantly lower dependence of adhesion force and discharge capacity at higher C‐rates on the drying rate is shown when using porous, nanostructured particles instead of solid particles. Binder migration and thus an inhomogeneous concentration distribution of the polyvinylidene fluoride binder is less pronounced for these electrodes during faster drying. Cell tests with half cells show that after increasing the drying rate by more than 350%, the discharge capacity of the electrodes consisting of solid NCM is reduced by about 63% at 5C while for the electrodes made of porous material no reduction is measured.