Douglas Maxwell Sassaman
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Douglas Maxwell Sassaman has a total of 16 co-authors. Here are the top co-authors by number of shared publications:
Desiderio Kovar
Univ Texas Austin, Dept Mech Engn, Austin, TX 78712 USA
2 shared publicationsMatthew Ide
ExxonMobil Research and Development Company, Annandale, USA
2 shared publications- Carolyn C. Seepersad
G.W. Woodruff School of Mechanical Engineering, Georgia Institute of Technology, Atlanta, GA 30318, USA
1 shared publication Carolyn Seepersad
Center for Additive Manufacturing and Design Innovation and Walker Department of Mechanical Engineering The University of Texas at Austin 78712 Austin TX
1 shared publicationCraig Milroy
Texas Research Institute Austin, Austin, USA
1 shared publication- Desiderio Kovar
Department of Mechanical Engineering University of Texas at Austin Austin Texas USA
1 shared publication
Latest Publications
- Open Access
Circularity: Understanding the Environmental Tradeoffs of Additive Manufacturing with Waste Plastics
This paper examines the emissions tradeoffs of additive manufacturing (i.e., 3D printing) using plastic waste in fused granular fabrication (FGF) versus traditional fused filament fabrication (FFF) and injection molding (IM). A ‘cradle-to-gate’ life cycle assessment (LCA) was utilized to compare these methods, built in OpenLCA v1.11.0 with the Ecoinvent v3.9.1 database. Different scenarios were used to evaluate the impacts of varying transportation and material inputs, highlighting critical emission contributors in manufacturing plastic goods. FGF with waste plastic can significantly reduce climate impact by 82.1% relative to FFF and 70.6% relative to IM for a specified unit product. Even with varied transportation and materials, FGF is a lower CO2-equivalent emitting method. Utilizing FGF with waste plastic as a manufacturing method could reduce emissions and divert plastic from landfills and the environment, thereby contributing to a circular plastic economy.
Open AccessCircularity: Understanding the Environmental Tradeoffs of Additive Manufacturing with Waste Plastics
This paper examines the emissions tradeoffs of additive manufacturing (i.e., 3D printing) using plastic waste in fused granular fabrication (FGF) versus traditional fused filament fabrication (FFF) and injection molding (IM). A ‘cradle-to-gate’ life cycle assessment (LCA) was utilized to compare these methods, built in OpenLCA v1.11.0 with the Ecoinvent v3.9.1 database. Different scenarios were used to evaluate the impacts of varying transportation and material inputs, highlighting critical emission contributors in manufacturing plastic goods. FGF with waste plastic can significantly reduce climate impact by 82.1% relative to FFF and 70.6% relative to IM for a specified unit product. Even with varied transportation and materials, FGF is a lower CO2-equivalent emitting method. Utilizing FGF with waste plastic as a manufacturing method could reduce emissions and divert plastic from landfills and the environment, thereby contributing to a circular plastic economy.
- Open Access
- 25 January 2022
- Published by Elsevier in Additive Manufacturing Letters
- Vol. 2
Design of an In-situ microscope for selective laser sintering
- 25 January 2022
- Published by Elsevier in Additive Manufacturing Letters
- Vol. 2
Open AccessDesign of an In-situ microscope for selective laser sintering
- 21 January 2022
- Published by Springer Nature in JOM
- Vol. 74 (3) , 1102-1110
A Method for Predicting Powder Flowability for Selective Laser Sintering
- 21 January 2022
- Published by Springer Nature in JOM
- Vol. 74 (3) , 1102-1110
A Method for Predicting Powder Flowability for Selective Laser Sintering
- Open Access
- 1 January 2022
- Published by Elsevier in SSRN Electronic Journal
Design of an In-Situ Microscope for Selective Laser Sintering
The phenomena responsible particle fusion during selective laser sintering (SLS) have been modeled, but attempts at experimental validation have been limited to unrealistic conditions compared to those used in commercial SLS processes. We have designed, implemented, and tested an instrument that is capable of performing in situ microscopy to image particle-scale dynamics of the SLS process at realistic scan speeds, temperatures, and gas environments. The instrument uses a combination of purchased and manufactured components to capture video at length scales of ~1 µm and timescales of ~1 ms. Spatial and temporal calibration is performed so that the laser position can be mapped onto the recorded video. Results show that laser melting of polymer is accompanied by particle rearrangement that occurs over an extended time (~10 ms) after the laser scans a particular location. The findings highlight the importance of performing in situ microscopy under realistic conditions for SLS.
- 1 January 2022
- Published by Elsevier in SSRN Electronic Journal
Open AccessDesign of an In-Situ Microscope for Selective Laser Sintering
The phenomena responsible particle fusion during selective laser sintering (SLS) have been modeled, but attempts at experimental validation have been limited to unrealistic conditions compared to those used in commercial SLS processes. We have designed, implemented, and tested an instrument that is capable of performing in situ microscopy to image particle-scale dynamics of the SLS process at realistic scan speeds, temperatures, and gas environments. The instrument uses a combination of purchased and manufactured components to capture video at length scales of ~1 µm and timescales of ~1 ms. Spatial and temporal calibration is performed so that the laser position can be mapped onto the recorded video. Results show that laser melting of polymer is accompanied by particle rearrangement that occurs over an extended time (~10 ms) after the laser scans a particular location. The findings highlight the importance of performing in situ microscopy under realistic conditions for SLS.
- Open Access
Geometry Limitations in Indirect Selective Laser Sintering of Alumina
Ceramics containing open channels with complex geometries can be manufactured by additive manufacturing (AM) and are of great interest in clean energy technologies. However, design limitations and guidelines for manufacturing these architectures with AM have not yet been established. In this work, we compare previously proposed geometry limitations for polymer selective laser sintering (SLS) to the geometries produced using indirect SLS in alumina. We focus on a subset of model shapes that are simple to produce and measure. We show that these rules provide a starting point for the design and manufacture of ceramic geometries using indirect SLS. However, there are additional considerations for AM of ceramics by indirect SLS that further limit the geometries that can be produced.
Open AccessGeometry Limitations in Indirect Selective Laser Sintering of Alumina
Ceramics containing open channels with complex geometries can be manufactured by additive manufacturing (AM) and are of great interest in clean energy technologies. However, design limitations and guidelines for manufacturing these architectures with AM have not yet been established. In this work, we compare previously proposed geometry limitations for polymer selective laser sintering (SLS) to the geometries produced using indirect SLS in alumina. We focus on a subset of model shapes that are simple to produce and measure. We show that these rules provide a starting point for the design and manufacture of ceramic geometries using indirect SLS. However, there are additional considerations for AM of ceramics by indirect SLS that further limit the geometries that can be produced.