Kirill Misiiuk
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Kirill Misiiuk has a total of 13 co-authors. Here are the top co-authors by number of shared publications:
- Sam Lowrey
Department of Physics, University of Otago, 730 Cumberland Street, Dunedin 9016, New Zealand
7 shared publications - Andrew D. Sommers
Miami Univ, Dept Mech & Mfg Engn, Oxford, OH 45056 USA
5 shared publications Richard Blaikie
Department of Physics, University of Otago, Dunedin, New Zealand
4 shared publicationsAndrew Sommers
Department of Mechanical & Manufacturing Engineering, Miami University, 501 East High Street, Oxford, Ohio 45056, United States
3 shared publications- Richard J. Blaikie
Department of Physics University of Otago Dunedin New Zealand
3 shared publications - Geoff. R. Willmott
The MacDiarmid Institute for Advanced Materials and Nanotechnology, Victoria University of Wellington, Wellington 6140, New Zealand
2 shared publications
Latest Publications
- 18 February 2026
- Published by American Chemical Society (ACS) in Langmuir
- Vol. 42 (8) , 6458-6470
Curvature-Driven Droplet Transport and Spontaneous Motion Using Concentric Ring Structures
Directional motion of droplets following impact is often attributed to gradients in surface wettability, but such motion can also emerge from geometric asymmetry on microstructured surfaces with a fixed pitch. Using high-speed imaging and goniometric analysis, we show in this study that 2.6 mm water droplets impacting concentric rings with pitch values of 25 and 100 μm at Weber numbers of 1.6-31.6 exhibit a net inward motion. This occurs despite the absence of any topographic or chemical gradient. Goniometric analysis revealed nonuniform wetting properties arising from fabrication-induced variations, while a simple model of the contact area demonstrated geometric asymmetry in curvature and wetting interaction at the end of the spreading phase. These combined effects produce "gradient-like" directional behavior on nongradient structures. Our findings highlight the underappreciated role of radial curvature in enhancing droplet transport and offer new avenues for fluid management and system design.
- 18 February 2026
- Published by American Chemical Society (ACS) in Langmuir
- Vol. 42 (8) , 6458-6470
Curvature-Driven Droplet Transport and Spontaneous Motion Using Concentric Ring Structures
Directional motion of droplets following impact is often attributed to gradients in surface wettability, but such motion can also emerge from geometric asymmetry on microstructured surfaces with a fixed pitch. Using high-speed imaging and goniometric analysis, we show in this study that 2.6 mm water droplets impacting concentric rings with pitch values of 25 and 100 μm at Weber numbers of 1.6-31.6 exhibit a net inward motion. This occurs despite the absence of any topographic or chemical gradient. Goniometric analysis revealed nonuniform wetting properties arising from fabrication-induced variations, while a simple model of the contact area demonstrated geometric asymmetry in curvature and wetting interaction at the end of the spreading phase. These combined effects produce "gradient-like" directional behavior on nongradient structures. Our findings highlight the underappreciated role of radial curvature in enhancing droplet transport and offer new avenues for fluid management and system design.
- Open Access
- 1 August 2025
- Published by AIP Publishing in Physics of Fluids
- Vol. 37 (8)
Transport of water droplets on metallic topographic gradients under forced vibration
Mechanical systems with moving parts and/or fluids, such as heat exchangers and turbomachinery, often experience vibration. Furthermore, these systems often benefit from effective water droplet removal to improve air-side heat transfer, avoid corrosion pitting of turbine blades, etc. Therefore, designing these systems requires a deeper understanding of a droplet's vibrational response on the surface of interest. In addition to uniform surfaces, topographic wetting gradients are also examined due to their ability to promote the spontaneous motion of water droplets on a surface for directional control. Topographic wetting gradients, produced in a one-step industrial process, have the potential to enhance heat exchanger performance, promote dropwise vs filmwise condensation, and facilitate more complete water drainage. This is enabled by net surface tension forces across the gradient, which drive droplet motion, especially when coupled with vibration. More specifically, we study the droplet behavior influenced by both vertical and horizontal vibration on polished and superhydrophobic coated aluminum surfaces as well as on uncoated aluminum surfaces containing variable-pitch micro/nanoengineered topographic wetting gradients. These experiments demonstrated a nonlinear response in the droplet behavior depending on the test surface and the combinations of forced vibration amplitude and frequency that were used to create the droplet lateral motion, which in some cases was up to 6.5 mm for droplet volumes of 5 and 10 μl. The range of examined frequencies was 20–200 Hz since these frequencies were observed on operating heat exchangers, whereas the range of displacements (i.e., amplitudes) was 50–2000 μm, which expands all previously reported data.
- 1 August 2025
- Published by AIP Publishing in Physics of Fluids
- Vol. 37 (8)
Open AccessTransport of water droplets on metallic topographic gradients under forced vibration
Mechanical systems with moving parts and/or fluids, such as heat exchangers and turbomachinery, often experience vibration. Furthermore, these systems often benefit from effective water droplet removal to improve air-side heat transfer, avoid corrosion pitting of turbine blades, etc. Therefore, designing these systems requires a deeper understanding of a droplet's vibrational response on the surface of interest. In addition to uniform surfaces, topographic wetting gradients are also examined due to their ability to promote the spontaneous motion of water droplets on a surface for directional control. Topographic wetting gradients, produced in a one-step industrial process, have the potential to enhance heat exchanger performance, promote dropwise vs filmwise condensation, and facilitate more complete water drainage. This is enabled by net surface tension forces across the gradient, which drive droplet motion, especially when coupled with vibration. More specifically, we study the droplet behavior influenced by both vertical and horizontal vibration on polished and superhydrophobic coated aluminum surfaces as well as on uncoated aluminum surfaces containing variable-pitch micro/nanoengineered topographic wetting gradients. These experiments demonstrated a nonlinear response in the droplet behavior depending on the test surface and the combinations of forced vibration amplitude and frequency that were used to create the droplet lateral motion, which in some cases was up to 6.5 mm for droplet volumes of 5 and 10 μl. The range of examined frequencies was 20–200 Hz since these frequencies were observed on operating heat exchangers, whereas the range of displacements (i.e., amplitudes) was 50–2000 μm, which expands all previously reported data.
- 12 November 2024
- Published by Springer Nature in Tribology Letters
- Vol. 72 (4) , 1-13
Mechanical Durability Testing and Self-Recovery of Topographically Modified Superhydrophobic Surfaces
- 12 November 2024
- Published by Springer Nature in Tribology Letters
- Vol. 72 (4) , 1-13
Mechanical Durability Testing and Self-Recovery of Topographically Modified Superhydrophobic Surfaces
- 25 April 2024
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 16 (18) , 24094-24107
Surveying the Directional Transport of Water Droplets upon Impact on Metallic Topographic Gradients
Drop impact phenomena on raw, polished, and topography-altered gradient surfaces are investigated and presented. The main aim of this study is to demonstrate that in using a one-step industrial patterning process, it is possible to obtain metal topographical wetting gradients that can produce various desired outcomes after droplet impact. The findings could be applied to improving wind or steam turbine blades. The ranges of Weber (We) and Reynolds (Re) numbers in the study are 3-300 and 650-6500, respectively. It is demonstrated that for a fixed We, the droplet transport outcomes change from bouncing-off to side-flipping to deposition depending on the impact location and the gradient strength. The effect of We in combination with the gradient strength was also considered to demonstrate droplet behavior similar to that observed on a uniform water repellent surface and on biphilic systems. In addition, full bouncing-off and directional control have been demonstrated. For the condition We = 95 ± 3, it was possible to achieve a maximum droplet recoil height of ∼6 mm and a side motion of almost 8 mm. A combination of different outcomes (e.g., splashing on one side of a droplet and passive horizontal translation on another) was observed on the studied gradients at We > 200 due to different wetting regimes across the droplet's three-phase line.
- 25 April 2024
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 16 (18) , 24094-24107
Surveying the Directional Transport of Water Droplets upon Impact on Metallic Topographic Gradients
Drop impact phenomena on raw, polished, and topography-altered gradient surfaces are investigated and presented. The main aim of this study is to demonstrate that in using a one-step industrial patterning process, it is possible to obtain metal topographical wetting gradients that can produce various desired outcomes after droplet impact. The findings could be applied to improving wind or steam turbine blades. The ranges of Weber (We) and Reynolds (Re) numbers in the study are 3-300 and 650-6500, respectively. It is demonstrated that for a fixed We, the droplet transport outcomes change from bouncing-off to side-flipping to deposition depending on the impact location and the gradient strength. The effect of We in combination with the gradient strength was also considered to demonstrate droplet behavior similar to that observed on a uniform water repellent surface and on biphilic systems. In addition, full bouncing-off and directional control have been demonstrated. For the condition We = 95 ± 3, it was possible to achieve a maximum droplet recoil height of ∼6 mm and a side motion of almost 8 mm. A combination of different outcomes (e.g., splashing on one side of a droplet and passive horizontal translation on another) was observed on the studied gradients at We > 200 due to different wetting regimes across the droplet's three-phase line.
- 16 November 2023
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 33 (22) , 12708-12720
Direction, Shape, and Scale Dependence of Ice Adhesion on Topographical Wetting Gradients
- 16 November 2023
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 33 (22) , 12708-12720
Direction, Shape, and Scale Dependence of Ice Adhesion on Topographical Wetting Gradients
- Open Access
- 1 May 2023
- Published by AIP Publishing in Physics of Fluids
- Vol. 35 (5)
New testing method for the evaluation of topographical gradients of varying strength
Passive gradient motion found in nature is becoming a point of interest for heat exchange and green energy technologies. Surfaces with a topographical gradient could potentially enhance heat exchanger performance, promote dropwise vs filmwise condensation, or delay icing on wind turbines by assisting in the removal of condensed or impacted droplets. Coating-free topographical surface tension gradients can be fabricated via various methods and need to be examined in terms of their capability for spontaneous droplet motion. In this work, a simple experimental method, coupled with numerical modeling and force analysis, for examining variable-pitch micro/nanoengineered hierarchical superhydrophobic gradients is shown. The method was validated against numerical calculations, allowing the strength of the gradients to be compared. In most cases, model predictions for droplet travel distance and velocity were within 20% of the measured data. This method could also be useful for gradient design improvements in the absence of spontaneous motion on a horizontal surface.
- 1 May 2023
- Published by AIP Publishing in Physics of Fluids
- Vol. 35 (5)
Open AccessNew testing method for the evaluation of topographical gradients of varying strength
Passive gradient motion found in nature is becoming a point of interest for heat exchange and green energy technologies. Surfaces with a topographical gradient could potentially enhance heat exchanger performance, promote dropwise vs filmwise condensation, or delay icing on wind turbines by assisting in the removal of condensed or impacted droplets. Coating-free topographical surface tension gradients can be fabricated via various methods and need to be examined in terms of their capability for spontaneous droplet motion. In this work, a simple experimental method, coupled with numerical modeling and force analysis, for examining variable-pitch micro/nanoengineered hierarchical superhydrophobic gradients is shown. The method was validated against numerical calculations, allowing the strength of the gradients to be compared. In most cases, model predictions for droplet travel distance and velocity were within 20% of the measured data. This method could also be useful for gradient design improvements in the absence of spontaneous motion on a horizontal surface.
- Open Access
- 1 February 2023
- Published by AIP Publishing in Physics of Fluids
- Vol. 35 (2) , 024108
Force balance model for spontaneous droplet motion on bio-inspired topographical surface tension gradients
Passive gradient-driven droplet motion has been demonstrated in nature, inspiring coating-free surface tension gradient surfaces that can be fabricated via laser ablation. These surfaces can potentially enhance heat exchanger performance, promoting drop-wise over film-wise condensation, and be suitable for lab-on-a-chip applications, allowing the directional transport of microliter size droplets. In this work, a theoretical model and its application to variable-pitch hierarchical superhydrophobic gradients are discussed, and the method is experimentally validated against various gradient topographical designs. The proposed force balance model allows analysis of the impact of the topography on the forces acting on the droplet. The discrepancy between modeled and observed contact angles in most cases does not exceed 10%. The modeled droplet footprint fits the experimentally measured ones with an error of less than 10% for most cases. Though modeled motion distances were twice greater than experimentally observed ones, the comparison of the proposed model with the originally developed theory showed that the difference in the net force was less than 5%. Both observed and average velocities were within less than 30% difference. Like the traditional models, the new model overestimates droplet kinematics; however, it does not require knowledge a priori of all the contact angles across the gradient during droplet motion, relying only on the material's surface tension and the local surface area fraction. Therefore, the model presents a simplified and convenient means of designing a linear topographical gradient for spontaneous droplet motion.
- 1 February 2023
- Published by AIP Publishing in Physics of Fluids
- Vol. 35 (2) , 024108
Open AccessForce balance model for spontaneous droplet motion on bio-inspired topographical surface tension gradients
Passive gradient-driven droplet motion has been demonstrated in nature, inspiring coating-free surface tension gradient surfaces that can be fabricated via laser ablation. These surfaces can potentially enhance heat exchanger performance, promoting drop-wise over film-wise condensation, and be suitable for lab-on-a-chip applications, allowing the directional transport of microliter size droplets. In this work, a theoretical model and its application to variable-pitch hierarchical superhydrophobic gradients are discussed, and the method is experimentally validated against various gradient topographical designs. The proposed force balance model allows analysis of the impact of the topography on the forces acting on the droplet. The discrepancy between modeled and observed contact angles in most cases does not exceed 10%. The modeled droplet footprint fits the experimentally measured ones with an error of less than 10% for most cases. Though modeled motion distances were twice greater than experimentally observed ones, the comparison of the proposed model with the originally developed theory showed that the difference in the net force was less than 5%. Both observed and average velocities were within less than 30% difference. Like the traditional models, the new model overestimates droplet kinematics; however, it does not require knowledge a priori of all the contact angles across the gradient during droplet motion, relying only on the material's surface tension and the local surface area fraction. Therefore, the model presents a simplified and convenient means of designing a linear topographical gradient for spontaneous droplet motion.
- 3 February 2022
- Published by American Chemical Society (ACS) in Langmuir
- Vol. 38 (6) , 1954-1965
Development of a Coating-Less Aluminum Superhydrophobic Gradient for Spontaneous Water Droplet Motion Using One-Step Laser-Ablation
Nature shows various approaches to create superhydrophobicity, such as the lotus leaf, where the superhydrophobic (SHPB) surface arising from its hierarchical surface consists of random microscale bumps with superimposed nanoscale hairs. Some natural systems, such as the hydrophilic silk of some spider’s webs, even allow the passive transport of water droplets from one part of a surface to another by creating gradients in surface tension and Laplace pressure. We look to combine both ideas and replicate the superb water repellence of the lotus leaf and the surface tension gradient-driven motion of the spider silk to form an all-metal, coating-less surface that promotes spontaneous droplet motion. We present the design, fabrication, and investigation of such superhydrophobic gradient surfaces on aluminum, which are aimed at spontaneous water droplet movement for improved surface water management. One surface demonstrates a droplet travel distance of almost 2 mm for a 11 μL droplet volume. We also present surfaces that map the theoretical ranges of the surface tension gradient surfaces tested here.
- 3 February 2022
- Published by American Chemical Society (ACS) in Langmuir
- Vol. 38 (6) , 1954-1965
Development of a Coating-Less Aluminum Superhydrophobic Gradient for Spontaneous Water Droplet Motion Using One-Step Laser-Ablation
Nature shows various approaches to create superhydrophobicity, such as the lotus leaf, where the superhydrophobic (SHPB) surface arising from its hierarchical surface consists of random microscale bumps with superimposed nanoscale hairs. Some natural systems, such as the hydrophilic silk of some spider’s webs, even allow the passive transport of water droplets from one part of a surface to another by creating gradients in surface tension and Laplace pressure. We look to combine both ideas and replicate the superb water repellence of the lotus leaf and the surface tension gradient-driven motion of the spider silk to form an all-metal, coating-less surface that promotes spontaneous droplet motion. We present the design, fabrication, and investigation of such superhydrophobic gradient surfaces on aluminum, which are aimed at spontaneous water droplet movement for improved surface water management. One surface demonstrates a droplet travel distance of almost 2 mm for a 11 μL droplet volume. We also present surfaces that map the theoretical ranges of the surface tension gradient surfaces tested here.
- 20 January 2022
- Published by American Chemical Society (ACS) in Langmuir
- Vol. 38 (4) , 1386-1397
Study of Micro- and Nanopatterned Aluminum Surfaces Using Different Microfabrication Processes for Water Management
Superhydrophobic surfaces demonstrate extreme water-repellence, promoting drop-wise over film-wise condensation, increasing liquid mobility, and reducing thermal resistance for heat-exchanger applications. Introducing topographic structures can lead to modified surface free energy, as inspired by natural systems like the lotus leaf, potentially allowing coating-free ice- and frost-free surfaces under certain conditions. This work presents a study of coating-free aluminum micro/nanopatterns fabricated using micromilling or laser-etching techniques and the resultant wetting properties. Our review and experiments clarify the roles of line-edge-roughness and microstructural geometry from each microfabrication technique, which manifests in technique-specific nano- to midmicro-scale roughness, producing a hierarchical structure in both cases. For micromilling, line-edge-roughness consists of jagged burrs of 1–8 μm thickness with 10–25 μm periodicity along the microlines with constantly changing height on the order of 1–20 μm. These effects simultaneously raise the water contact angle from 52° (unprocessed aluminum) up to 136° but with strong edge pinning effects. On the other hand, laser-etched surfaces exhibit line-edge-roughness with a microstructure of 3–20 μm width and 5–10 μm in height superimposed with evenly spread spikes of 50–250 nm. This results in a high contact angle (>150°) coupled with a low contact angle hysteresis (<15°), promoting superhydrophobicity on a coating-free aluminum surface. It is also shown that for certain cases, line-edge-roughness is more important for the resultant wetting properties than the structure geometry.
- 20 January 2022
- Published by American Chemical Society (ACS) in Langmuir
- Vol. 38 (4) , 1386-1397
Study of Micro- and Nanopatterned Aluminum Surfaces Using Different Microfabrication Processes for Water Management
Superhydrophobic surfaces demonstrate extreme water-repellence, promoting drop-wise over film-wise condensation, increasing liquid mobility, and reducing thermal resistance for heat-exchanger applications. Introducing topographic structures can lead to modified surface free energy, as inspired by natural systems like the lotus leaf, potentially allowing coating-free ice- and frost-free surfaces under certain conditions. This work presents a study of coating-free aluminum micro/nanopatterns fabricated using micromilling or laser-etching techniques and the resultant wetting properties. Our review and experiments clarify the roles of line-edge-roughness and microstructural geometry from each microfabrication technique, which manifests in technique-specific nano- to midmicro-scale roughness, producing a hierarchical structure in both cases. For micromilling, line-edge-roughness consists of jagged burrs of 1–8 μm thickness with 10–25 μm periodicity along the microlines with constantly changing height on the order of 1–20 μm. These effects simultaneously raise the water contact angle from 52° (unprocessed aluminum) up to 136° but with strong edge pinning effects. On the other hand, laser-etched surfaces exhibit line-edge-roughness with a microstructure of 3–20 μm width and 5–10 μm in height superimposed with evenly spread spikes of 50–250 nm. This results in a high contact angle (>150°) coupled with a low contact angle hysteresis (<15°), promoting superhydrophobicity on a coating-free aluminum surface. It is also shown that for certain cases, line-edge-roughness is more important for the resultant wetting properties than the structure geometry.