Branka Pilić
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Branka Pilić has a total of 14 co-authors. Here are the top co-authors by number of shared publications:
- Aleksandra Miletić
Faculty of Technology Novi Sad, University of Novi Sad, Bulevar cara Lazara 1, 21000 Novi Sad, Serbia
1 shared publication Branislava Petronijevic-Sarcev
University of Novi Sad, Faculty of Medicine, Department of Dentistry, Novi Sad, Serbia
1 shared publicationIvan Sarcev
University of Novi Sad, Faculty of Medicine, Department of Dentistry, Novi Sad, Serbia
1 shared publication- Ivana Jurič
University of Novi Sad, Faculty of Technical Sciences, Department of Graphic Engineering and Design, Novi Sad, Serbia
1 shared publication - Magdolna Pál
University of Novi Sad, Faculty of Technical Sciences, Department of Graphic Engineering and Design, Novi Sad, Serbia
1 shared publication - Milan Vraneš
Department of Chemistry, Biochemistry and Environmental Protection, Faculty of Sciences, University of Novi Sad, Trg Dositeja Obradovića 3, 21000 Novi Sad, Serbia
1 shared publication
Latest Publications
- 1 November 2026
- Published by Faculty of Technical Sciences
- Vol. 13, 179-188
Printing Possibility on Biopolymer Based Films
The growing demand for sustainable packaging and printed products has increased interest in biodegradable polymeric materials as environmentally friendly alternatives to conventional plastics. However, their printability and color reproduction characteristics remain insufficiently investigated. This study evaluates the suitability of biodegradable polymer films based on poly (lactic acid) (PLA) and its blends with poly (butylene succinate) (PBS), poly (hydroxybutyrate) (PHB), and poly (hydroxybutyrate-co-valerate) (PHBV) for UV inkjet printing applications. Biopolymer films were produced by flat-die extrusion under controlled processing conditions. The printed samples were obtained using a UV inkjet printing system under standardized printing parameters. Print quality was assessed through optical density and CIELAB color measurements using a spectrophotometer, while the chemical structure of the prepared blends was examined by FTIR spectroscopy to verify the absence of chemical reactions during processing. The obtained results indicate that all investigated biopolymer blends provide high optical density values with only minor variations among formulations. Although differences in lightness (L*) were observed between individual blends, chromatic coordinates (a* and b*) remained relatively stable, demonstrating consistent color reproduction across the tested materials. FTIR analysis confirmed that no new chemical bonds were formed during extrusion, indicating that the prepared materials represent physical polymer blends. The findings demonstrate that PLA-based biodegradable films and their blends exhibit promising printability for UV inkjet technology while maintaining their chemical integrity after processing. These results contribute to the development of sustainable printed products and provide a basis for further optimization of biodegradable substrates intended for graphic and packaging applications
- 1 November 2026
- Published by Faculty of Technical Sciences
- Vol. 13, 179-188
Printing Possibility on Biopolymer Based Films
The growing demand for sustainable packaging and printed products has increased interest in biodegradable polymeric materials as environmentally friendly alternatives to conventional plastics. However, their printability and color reproduction characteristics remain insufficiently investigated. This study evaluates the suitability of biodegradable polymer films based on poly (lactic acid) (PLA) and its blends with poly (butylene succinate) (PBS), poly (hydroxybutyrate) (PHB), and poly (hydroxybutyrate-co-valerate) (PHBV) for UV inkjet printing applications. Biopolymer films were produced by flat-die extrusion under controlled processing conditions. The printed samples were obtained using a UV inkjet printing system under standardized printing parameters. Print quality was assessed through optical density and CIELAB color measurements using a spectrophotometer, while the chemical structure of the prepared blends was examined by FTIR spectroscopy to verify the absence of chemical reactions during processing. The obtained results indicate that all investigated biopolymer blends provide high optical density values with only minor variations among formulations. Although differences in lightness (L*) were observed between individual blends, chromatic coordinates (a* and b*) remained relatively stable, demonstrating consistent color reproduction across the tested materials. FTIR analysis confirmed that no new chemical bonds were formed during extrusion, indicating that the prepared materials represent physical polymer blends. The findings demonstrate that PLA-based biodegradable films and their blends exhibit promising printability for UV inkjet technology while maintaining their chemical integrity after processing. These results contribute to the development of sustainable printed products and provide a basis for further optimization of biodegradable substrates intended for graphic and packaging applications
- 1 January 2023
- Published by University Library in Kragujevac
- p. 148-151
Development of Nanomaterials for Sustainable Food Packaging Applications
The use of biodegradable polymers from renewable resources in polymer manufacturing, food packaging and for medical application is becoming a favorable option over petroleum-based plastics. Among all biopolymers, biopolyesters poly(lactic acid) (PLA) and polyhidroxyalkanoates (PHAs) are considered as the most commercially promising bioplastics. PLA is a biopolyester produced by polymerization of D-, L- lactic acids originating through fermentation of simple sugars from agricultural sources (corn, potato, sugar cane, sugar beet, etc.). PHA is a generic designation for biopolyesters produced by controlled microbial fermentation in the presence of an abundant source of sugars or lipids. The focus of this study was to prepare fully biodegradable flexible nanomaterials using PLA and poly(hydroxybutyrate) (PHB) polymer blend solution by means of electrospinning technique. Since PHB possesses low resistance to thermal degradation with melting temperatures close to degradation and narrowing the processing window, the electrospinning technique reduces energy consumption and avoids thermal degradation during processing. A complete morphological, structural and thermal characterization of the developed materials was conducted at the same time.
- 1 January 2023
- Published by University Library in Kragujevac
- p. 148-151
Development of Nanomaterials for Sustainable Food Packaging Applications
The use of biodegradable polymers from renewable resources in polymer manufacturing, food packaging and for medical application is becoming a favorable option over petroleum-based plastics. Among all biopolymers, biopolyesters poly(lactic acid) (PLA) and polyhidroxyalkanoates (PHAs) are considered as the most commercially promising bioplastics. PLA is a biopolyester produced by polymerization of D-, L- lactic acids originating through fermentation of simple sugars from agricultural sources (corn, potato, sugar cane, sugar beet, etc.). PHA is a generic designation for biopolyesters produced by controlled microbial fermentation in the presence of an abundant source of sugars or lipids. The focus of this study was to prepare fully biodegradable flexible nanomaterials using PLA and poly(hydroxybutyrate) (PHB) polymer blend solution by means of electrospinning technique. Since PHB possesses low resistance to thermal degradation with melting temperatures close to degradation and narrowing the processing window, the electrospinning technique reduces energy consumption and avoids thermal degradation during processing. A complete morphological, structural and thermal characterization of the developed materials was conducted at the same time.
- Open Access
- 1 January 2021
- Published by National Library of Serbia in Vojnosanitetski Pregled
- Vol. 78 (12) , 1324-1329
Autopolymerized poly(methyl methacrylate) reinforced with alumina nanoparticles
Background/Aim: Mechanical properties, most significantly flexural strength of cold polymerized acrylic dental materials, used for denture reparation are lower compared to the equivalent hot polymerized materials. This paradox can be rectified by the aplication of alumina nanoparticles, which is the aim of this work. Methods: The liquid component of the commercial autopolimerized denture reline resin was modified with 0.05 %, 0.2 % and 1.5 wt. % 13 nm hydrophobic Al2O3. These mixtures, along with the unmodified liquid, were mixed with the powder component to form test specimens. Flexural modulus and strength were tested, while the results were stastistically evaluated by one way ANOVA analysis followed by Tukey’s test. Differential scanning calorimetry, scaning electron microscopy and energy dispersive x-ray analysis analyses were performed to assess the heat and fracture surface features. Results: Statistically significant increase in flexural modulus was obtained only for 0.2 % nanoparticle content, while flexural strength was significantly increased for specimens modified with 0.05 and 0.2 % nanoparticles. The rise of nanoparticle content to 1.5 % contributes to the formation of agglomerates, giving unsatisfactory mechanical properties. Also, the rise in glass transition temperature was noted for the most effective 0.05 and 0.2 % Al2O3 contents. Conclusions: 0.2 % 13 nm Al2O3 loading is the most effective in imropving the tested mechanical properties of cold polimerized poly(methyl methacrylate) reline resin.
- 1 January 2021
- Published by National Library of Serbia in Vojnosanitetski Pregled
- Vol. 78 (12) , 1324-1329
Open AccessAutopolymerized poly(methyl methacrylate) reinforced with alumina nanoparticles
Background/Aim: Mechanical properties, most significantly flexural strength of cold polymerized acrylic dental materials, used for denture reparation are lower compared to the equivalent hot polymerized materials. This paradox can be rectified by the aplication of alumina nanoparticles, which is the aim of this work. Methods: The liquid component of the commercial autopolimerized denture reline resin was modified with 0.05 %, 0.2 % and 1.5 wt. % 13 nm hydrophobic Al2O3. These mixtures, along with the unmodified liquid, were mixed with the powder component to form test specimens. Flexural modulus and strength were tested, while the results were stastistically evaluated by one way ANOVA analysis followed by Tukey’s test. Differential scanning calorimetry, scaning electron microscopy and energy dispersive x-ray analysis analyses were performed to assess the heat and fracture surface features. Results: Statistically significant increase in flexural modulus was obtained only for 0.2 % nanoparticle content, while flexural strength was significantly increased for specimens modified with 0.05 and 0.2 % nanoparticles. The rise of nanoparticle content to 1.5 % contributes to the formation of agglomerates, giving unsatisfactory mechanical properties. Also, the rise in glass transition temperature was noted for the most effective 0.05 and 0.2 % Al2O3 contents. Conclusions: 0.2 % 13 nm Al2O3 loading is the most effective in imropving the tested mechanical properties of cold polimerized poly(methyl methacrylate) reline resin.