Leonhard Kilian Doppelbauer
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Leonhard Kilian Doppelbauer has a total of 26 co-authors. Here are the top co-authors by number of shared publications:
- Astrid Pechstein
Institute of Technical Mechanics, Johannes Kepler University Linz, Linz, Austria
2 shared publications - Philipp S. Stelzer
Ludwig-Maximilians-Universität München , Institut für Allgemeine und Vergleichende Literaturwissenschaft, Schellingstraße 3 , München , Deutschland Germany
2 shared publications Zoltan Major
2 shared publicationsZoltán Major
2 shared publicationsAlexander Humer
1 shared publication- Alexander Humer
Institute of Technical Mechanics, Johannes Kepler University Linz, Linz, Austria
1 shared publication
Latest Publications
- Open Access
- 10 February 2026
- Published by Springer Nature in Meccanica
- Vol. 61 (1) , 30
Homogenization of periodically structured contact interfaces
This contribution presents a homogenization approach for the computationally efficient modeling of two-dimensional solid bodies that interact through structured surfaces. Instead of resolving the detailed microscale geometry, the method introduces a finite-thickness surrogate layer that captures the essential mechanical response of the structured contact zone. The proposed formulation is based on the description of microscale quantities, such as (normal) gap and relative sliding velocity, which are transferred to the macroscale using internal volumetric variables. The elastic behavior of the surrogate layer is identified through a mean-field homogenization approach that accounts for the non-linear dependency of stress response on the relative slip. As a result, the anisotropic and history-dependent behavior of the interface can be captured within the model. The proposed method is validated using two benchmark problems: a vertical stack of two structured blocks and a knurled interference fit. In both cases, the finite-thickness layer accurately reproduces the mechanical response of the fully resolved model, i.e., stick–slip transitions, hysteresis, and partial interface separation. The good agreement with the reference solutions, combined with a significant reduction in computational cost, demonstrates the potential of the method for efficient multi-scale interface modeling.
- 10 February 2026
- Published by Springer Nature in Meccanica
- Vol. 61 (1) , 30
Open AccessHomogenization of periodically structured contact interfaces
This contribution presents a homogenization approach for the computationally efficient modeling of two-dimensional solid bodies that interact through structured surfaces. Instead of resolving the detailed microscale geometry, the method introduces a finite-thickness surrogate layer that captures the essential mechanical response of the structured contact zone. The proposed formulation is based on the description of microscale quantities, such as (normal) gap and relative sliding velocity, which are transferred to the macroscale using internal volumetric variables. The elastic behavior of the surrogate layer is identified through a mean-field homogenization approach that accounts for the non-linear dependency of stress response on the relative slip. As a result, the anisotropic and history-dependent behavior of the interface can be captured within the model. The proposed method is validated using two benchmark problems: a vertical stack of two structured blocks and a knurled interference fit. In both cases, the finite-thickness layer accurately reproduces the mechanical response of the fully resolved model, i.e., stick–slip transitions, hysteresis, and partial interface separation. The good agreement with the reference solutions, combined with a significant reduction in computational cost, demonstrates the potential of the method for efficient multi-scale interface modeling.
- Open Access
- 7 December 2024
- Published by Elsevier in European Journal of Mechanics - A/Solids
- Vol. 111
Hysteresis in knurled interference fits
- 7 December 2024
- Published by Elsevier in European Journal of Mechanics - A/Solids
- Vol. 111
Open AccessHysteresis in knurled interference fits
- Open Access
- 20 November 2024
- Published by SAGE Publications in Journal of Intelligent Material Systems and Structures
- Vol. 36 (16) , 1104-1117
Thermodynamically consistent modeling of viscoelastic solids under finite strain
The present article is concerned with modeling the viscoelastic behavior of Polydimethylsiloxane (PDMS) in large-strain regime. Starting from the basic principles of thermodynamics, an incremental variational formulation is derived. Within this model, the free energy density and dissipation function determine elastic and viscous properties of the solid. The main contribution of this paper is the estimation of the parameters in the proposed phenomenological model from measurements conducted on Sylgard184 samples. This non-linear material model simplifies to a Prony-series representation in frequency domain in case of small deformations. The coefficients of this Prony-series are detected from dynamical temperature mechanical analysis measurements. Time-temperature superposition allows to combine measurements at different temperatures, such that a sufficiently large frequency range is available for subsequent fitting of Prony-parameters. A set of material parameters is thus provided. The incremental variational formulation directly lends itself to finite element discretization, where an efficient and stable choice of elements is proposed for radially symmetric problems. This formulation allows to verify the proposed model against experimental data gained in ball-drop experiments.
- 20 November 2024
- Published by SAGE Publications in Journal of Intelligent Material Systems and Structures
- Vol. 36 (16) , 1104-1117
Open AccessThermodynamically consistent modeling of viscoelastic solids under finite strain
The present article is concerned with modeling the viscoelastic behavior of Polydimethylsiloxane (PDMS) in large-strain regime. Starting from the basic principles of thermodynamics, an incremental variational formulation is derived. Within this model, the free energy density and dissipation function determine elastic and viscous properties of the solid. The main contribution of this paper is the estimation of the parameters in the proposed phenomenological model from measurements conducted on Sylgard184 samples. This non-linear material model simplifies to a Prony-series representation in frequency domain in case of small deformations. The coefficients of this Prony-series are detected from dynamical temperature mechanical analysis measurements. Time-temperature superposition allows to combine measurements at different temperatures, such that a sufficiently large frequency range is available for subsequent fitting of Prony-parameters. A set of material parameters is thus provided. The incremental variational formulation directly lends itself to finite element discretization, where an efficient and stable choice of elements is proposed for radially symmetric problems. This formulation allows to verify the proposed model against experimental data gained in ball-drop experiments.
- Open Access
- 23 March 2023
- Published by Elsevier in Composites Part A: Applied Science and Manufacturing
- Vol. 169
A macroscopic model of the compaction process during compression molding of carbon fiber sheet molding compounds
- 23 March 2023
- Published by Elsevier in Composites Part A: Applied Science and Manufacturing
- Vol. 169
Open AccessA macroscopic model of the compaction process during compression molding of carbon fiber sheet molding compounds
- Open Access
- 22 January 2022
- Published by Elsevier in Composites Part B: Engineering
- Vol. 234
Experimental feasibility and environmental impacts of compression molded discontinuous carbon fiber composites with opportunities for circular economy
- 22 January 2022
- Published by Elsevier in Composites Part B: Engineering
- Vol. 234
Open AccessExperimental feasibility and environmental impacts of compression molded discontinuous carbon fiber composites with opportunities for circular economy
- 13 January 2021
- Published by Springer Nature
- p. 741-755
Surface Roughness and Normal Force Effects on the Sliding and Rolling Behavior of POM-H Rolls
- 13 January 2021
- Published by Springer Nature
- p. 741-755
Surface Roughness and Normal Force Effects on the Sliding and Rolling Behavior of POM-H Rolls