Ahmad S.M. Al-Azzawi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Ahmad S.M. Al-Azzawi has a total of 11 co-authors. Here are the top co-authors by number of shared publications:
- Antigoni Barouni
Advanced Polymers and Composites (APC) Research Group, School of Mechanical and Design Engineering, University of Portsmouth, Anglesea Road, Anglesea Building, Portsmouth PO1 3DJ, UK
1 shared publication Carol A Featherston
School of Engineering, Cardiff University, Cardiff, CF24 3AA, UK
1 shared publicationCarol A. Featherston
1 shared publication- Carol A. Featherston
School of Engineering, Cardiff University, Cardiff CF24 3AA, UK
1 shared publication Chulin Jiang
1 shared publication- Colin Lupton
University of Portsmouth
1 shared publication
Latest Publications
- Open Access
- 23 August 2024
- Published by Elsevier in Composites Part B: Engineering
- Vol. 287
Impact characteristics of S2-glass fibre/FM94-epoxy composites under high and cryogenic temperatures: Experimental and numerical investigation
- 23 August 2024
- Published by Elsevier in Composites Part B: Engineering
- Vol. 287
Open AccessImpact characteristics of S2-glass fibre/FM94-epoxy composites under high and cryogenic temperatures: Experimental and numerical investigation
- Open Access
- 27 August 2022
- Published by Elsevier in Thin-Walled Structures
- Vol. 181
A novel semi-analytical approach for predicting the buckling and postbuckling behaviour of Glare fibre metal laminates
- 27 August 2022
- Published by Elsevier in Thin-Walled Structures
- Vol. 181
Open AccessA novel semi-analytical approach for predicting the buckling and postbuckling behaviour of Glare fibre metal laminates
- 17 November 2021
- Published by SAGE Publications in Journal of Reinforced Plastics and Composites
- Vol. 41 (5-6) , 167-186
Predicting interlaminar damage behaviour of fibre-metal laminates containing adhesive joints under bending loads
This study includes experimental and numerical investigations on fibre-metal laminate structures containing adhesive joints under static bending loads. Experimental tests were carried out on Glare® 4B specimens manufactured in-house and containing doubler joint features. Numerical analyses were performed using Abaqus software including damage in the glass fibre reinforced polymer layers, ductile damage in the resin pockets (FM94 epoxy) and plasticity in the metal layers. A new cohesive zone model coupling friction and interfacial shear under through-thickness compressive stress has been developed to simulate delamination initiation and growth at the metal/fibre interfaces with the adhesive joint under flexural loading. This model is implemented through a user-defined VUMAT subroutine in the Abaqus/Explicit software and includes two main approaches, firstly, combining friction and interfacial shear stresses created in the interlaminar layers of the fibre-metal laminate as a result of through-thickness stresses and secondly, considering elastic-plastic damage behaviour using a new cohesive zone model based on the trapezoidal law (which provides more accurate results for the simulation of toughened epoxy matrices than the commonly used bilinear cohesive zone model). Numerical results have been validated against experimental data from 4-point bending tests and a good correlation observed with respect to both crack initiation and evolution. Delamination and shear failure were noted to be the predominant failure modes under bending stresses as expected. This is due to the higher mode-II stresses introduced during bending which cause different damage evolution behaviour to that seen for axial stresses. Finite element results revealed that both friction and shear strength parameters generated from through-thickness compression stresses have a significant effect in predicting damage in fibre-metal laminate structures under this type of loading.
- 17 November 2021
- Published by SAGE Publications in Journal of Reinforced Plastics and Composites
- Vol. 41 (5-6) , 167-186
Predicting interlaminar damage behaviour of fibre-metal laminates containing adhesive joints under bending loads
This study includes experimental and numerical investigations on fibre-metal laminate structures containing adhesive joints under static bending loads. Experimental tests were carried out on Glare® 4B specimens manufactured in-house and containing doubler joint features. Numerical analyses were performed using Abaqus software including damage in the glass fibre reinforced polymer layers, ductile damage in the resin pockets (FM94 epoxy) and plasticity in the metal layers. A new cohesive zone model coupling friction and interfacial shear under through-thickness compressive stress has been developed to simulate delamination initiation and growth at the metal/fibre interfaces with the adhesive joint under flexural loading. This model is implemented through a user-defined VUMAT subroutine in the Abaqus/Explicit software and includes two main approaches, firstly, combining friction and interfacial shear stresses created in the interlaminar layers of the fibre-metal laminate as a result of through-thickness stresses and secondly, considering elastic-plastic damage behaviour using a new cohesive zone model based on the trapezoidal law (which provides more accurate results for the simulation of toughened epoxy matrices than the commonly used bilinear cohesive zone model). Numerical results have been validated against experimental data from 4-point bending tests and a good correlation observed with respect to both crack initiation and evolution. Delamination and shear failure were noted to be the predominant failure modes under bending stresses as expected. This is due to the higher mode-II stresses introduced during bending which cause different damage evolution behaviour to that seen for axial stresses. Finite element results revealed that both friction and shear strength parameters generated from through-thickness compression stresses have a significant effect in predicting damage in fibre-metal laminate structures under this type of loading.