Augusto Wohlgemuth Fleury Veloso da Silveira
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Augusto Wohlgemuth Fleury Veloso da Silveira has a total of 17 co-authors. Here are the top co-authors by number of shared publications:
- Luciano Coutinho Gomes
Faculty of Electrical Engineering, Federal University of Uberlandia (UFU), Uberlandia 38408-100, Brazil
6 shared publications - Ghunter Paulo Viajante
Power System Research Core (NuPSE), Federal Institute of Gois (IFG), Goinia, Gois, Brazil
3 shared publications D. A. Andrade
Laboratório de Acionamentos Elétricos da Universidade Federal de Uberlândia, Campus Santa Mônica, MG, Brasil
2 shared publications- Gustavo de Oliveira Machado
Universidade Federal de Uberlândia
2 shared publications - Marcos José de Moraes Filho
Serviço Nacional de Aprendizagem Industrial - MG
2 shared publications - Ricardo Tirone Fidelis
Laboratory of Electrical Drives (LaCE), Federal University of Uberlndia (UFU), Uberlndia, Minas Gerais, Brazil
2 shared publications
Latest Publications
- Open Access
- 1 January 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 14, 120762-120777
A Two-Stage Hybrid Architecture for Unknown Anomaly Detection in Rotating Machinery Bearings
- 1 January 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 14, 120762-120777
Open AccessA Two-Stage Hybrid Architecture for Unknown Anomaly Detection in Rotating Machinery Bearings
- Open Access
Impacts of Harmonic Voltage Distortions on the Dynamic Behavior and the PRPD Patterns of Partial Discharges in an Air Cavity Inside a Solid Dielectric Material
The monitoring of partial discharges (PDs) is one of the main methods used worldwide for evaluation and diagnosis of the insulation conditions in equipment powered by medium and high voltages. The occurrence of PDs is usually an indication of the appearance of insulation defects, which over time can compromise the dielectric withstand of the material used, increasing the probability of complete breakdown. In general, laboratory tests for detecting and registering PDs are carried out using purely sinusoidal voltages. However, it is very common for an electrical asset to be subjected at some point in its operating life to voltages distorted by harmonic components. Some studies reported in the literature reveal that harmonic distortions can affect the PDs’ characteristics, nevertheless, the effects of individual harmonic components on PDs still need to be analyzed. In this context, this paper proposes to evaluate the impacts of harmonic voltage distortions on the dynamic behavior and the phase-resolved partial discharge (PRPD) patterns of PDs in an air cavity within a solid dielectric material. For this, a simulation model was implemented, which was used to analyze the effects of applying distorted voltages composed of different harmonic orders (third, fifth, and seventh) and distinct levels of distortion (1%, 3%, 5%, 10%, 15%, and 20%). In addition, the influence of the third harmonic phase angle on PDs is also analyzed. The results extracted from the simulations revealed that the harmonic distortions caused changes in the numbers of PDs per cycle, in the mean apparent charges of the PDs per cycle, and in the PRPD patterns’ characteristics. These changes were very significant for higher distortion levels, which in practice may impair the interpretation of PD measurement records for the diagnosis of the condition of the insulation system.
Open AccessImpacts of Harmonic Voltage Distortions on the Dynamic Behavior and the PRPD Patterns of Partial Discharges in an Air Cavity Inside a Solid Dielectric Material
The monitoring of partial discharges (PDs) is one of the main methods used worldwide for evaluation and diagnosis of the insulation conditions in equipment powered by medium and high voltages. The occurrence of PDs is usually an indication of the appearance of insulation defects, which over time can compromise the dielectric withstand of the material used, increasing the probability of complete breakdown. In general, laboratory tests for detecting and registering PDs are carried out using purely sinusoidal voltages. However, it is very common for an electrical asset to be subjected at some point in its operating life to voltages distorted by harmonic components. Some studies reported in the literature reveal that harmonic distortions can affect the PDs’ characteristics, nevertheless, the effects of individual harmonic components on PDs still need to be analyzed. In this context, this paper proposes to evaluate the impacts of harmonic voltage distortions on the dynamic behavior and the phase-resolved partial discharge (PRPD) patterns of PDs in an air cavity within a solid dielectric material. For this, a simulation model was implemented, which was used to analyze the effects of applying distorted voltages composed of different harmonic orders (third, fifth, and seventh) and distinct levels of distortion (1%, 3%, 5%, 10%, 15%, and 20%). In addition, the influence of the third harmonic phase angle on PDs is also analyzed. The results extracted from the simulations revealed that the harmonic distortions caused changes in the numbers of PDs per cycle, in the mean apparent charges of the PDs per cycle, and in the PRPD patterns’ characteristics. These changes were very significant for higher distortion levels, which in practice may impair the interpretation of PD measurement records for the diagnosis of the condition of the insulation system.
- Open Access
- 27 March 2022
- Published by Research, Society and Development in Research, Society and Development
- Vol. 11 (5)
A new inductance estimator based on Lagrange Form polynomials for real-time switched reluctance machine control
This paper presents a new methodology for modeling the inductance curves of switched-reluctance machines using cubic splines based on Lagrange form polynomials. The proposed methodology allows for the estimation of the instantaneous inductance and derivative of the inductance in each phase of the machine. All steps of the proposed methodology are presented and discussed, detailing the information necessary for its use. The results of an experimental and computational simulation, both as a motor and a generator, are presented and discussed, and the estimated curves are compared with the design curves of each result. The inductance estimator was embedded in a low-cost DSP, and the machine was driven using an experimental bench. The experimental results are presented and compared with the simulation results, allowing for the evaluation of the accuracy level obtained by the proposed estimator. The estimator combines precision with low computational cost, which makes this method a strong candidate for systems that require estimation of machine parameters in real time, such as torque and flux, permitting the implementation of new control techniques.
- 27 March 2022
- Published by Research, Society and Development in Research, Society and Development
- Vol. 11 (5)
Open AccessA new inductance estimator based on Lagrange Form polynomials for real-time switched reluctance machine control
This paper presents a new methodology for modeling the inductance curves of switched-reluctance machines using cubic splines based on Lagrange form polynomials. The proposed methodology allows for the estimation of the instantaneous inductance and derivative of the inductance in each phase of the machine. All steps of the proposed methodology are presented and discussed, detailing the information necessary for its use. The results of an experimental and computational simulation, both as a motor and a generator, are presented and discussed, and the estimated curves are compared with the design curves of each result. The inductance estimator was embedded in a low-cost DSP, and the machine was driven using an experimental bench. The experimental results are presented and compared with the simulation results, allowing for the evaluation of the accuracy level obtained by the proposed estimator. The estimator combines precision with low computational cost, which makes this method a strong candidate for systems that require estimation of machine parameters in real time, such as torque and flux, permitting the implementation of new control techniques.
- Open Access
- 16 January 2022
- Published by Research, Society and Development in Research, Society and Development
- Vol. 11 (2)
Projeto otimizado e análise por elementos finitos de um motor a relutância variável 8/6 tetrafásico
O motor a relutância variável (MRV) tem sido considerado uma alternativa viável para substituir os motores elétricos clássicos em aplicações que demandam acionamentos com velocidades variáveis. Este motor é robusto, dispõe de uma construção simples e tem a vantagem de possuir um rotor que não necessita de enrolamentos ou ímãs permanentes para operar. Neste trabalho, um MRV 8/6 tetrafásico é projetado a fim de substituir um motor de indução trifásico (MIT), utilizando a mesma carcaça disponível. Na metodologia adotada para o projeto, os dados mecânicos da carcaça do MIT são utilizados como parâmetros iniciais para o cálculo das dimensões do MRV. A escolha dos ângulos dos arcos dos polos do MRV é otimizada através da análise por elementos finitos. Além disso, as simulações realizadas via elementos finitos possibilitam a visualização da distribuição do fluxo magnético na estrutura do MRV e o levantamento de dados importantes como os perfis de indutância e de fluxo concatenado, e o torque do motor projetado. O maior erro relativo obtido para a densidade de fluxo magnético no núcleo do motor foi de 1,69% e o torque resultante do MRV foi muito próximo do torque requerido inicialmente. Esses resultados apresentados validam o protótipo projetado e consolidam a metodologia de projeto utilizada.
- 16 January 2022
- Published by Research, Society and Development in Research, Society and Development
- Vol. 11 (2)
Open AccessProjeto otimizado e análise por elementos finitos de um motor a relutância variável 8/6 tetrafásico
O motor a relutância variável (MRV) tem sido considerado uma alternativa viável para substituir os motores elétricos clássicos em aplicações que demandam acionamentos com velocidades variáveis. Este motor é robusto, dispõe de uma construção simples e tem a vantagem de possuir um rotor que não necessita de enrolamentos ou ímãs permanentes para operar. Neste trabalho, um MRV 8/6 tetrafásico é projetado a fim de substituir um motor de indução trifásico (MIT), utilizando a mesma carcaça disponível. Na metodologia adotada para o projeto, os dados mecânicos da carcaça do MIT são utilizados como parâmetros iniciais para o cálculo das dimensões do MRV. A escolha dos ângulos dos arcos dos polos do MRV é otimizada através da análise por elementos finitos. Além disso, as simulações realizadas via elementos finitos possibilitam a visualização da distribuição do fluxo magnético na estrutura do MRV e o levantamento de dados importantes como os perfis de indutância e de fluxo concatenado, e o torque do motor projetado. O maior erro relativo obtido para a densidade de fluxo magnético no núcleo do motor foi de 1,69% e o torque resultante do MRV foi muito próximo do torque requerido inicialmente. Esses resultados apresentados validam o protótipo projetado e consolidam a metodologia de projeto utilizada.
- 1 September 2011
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 21650454,p. 55-60
Self-excited switched reluctance generator
This paper presents a study on the behavior of the self-excited switched reluctance generator (SSRG). Following an extensive bibliographic review about SSRGs, the mathematical model, principle of operation and simulation results of the generator dynamics is presented. A capacitor partially charged, in parallel with the load is used as a mean to provide the necessary amount of magnetic flux and start the generator's voltage built up. The arrangement is such that the generated voltage and current is delivered to the load in D.C. mode. To correctly represent the self excitation operation the mathematical model must take into account the core magnetic saturation, and that is observed here. Experimental results are included to validate the discussions presented.
- 1 September 2011
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 21650454,p. 55-60
Self-excited switched reluctance generator
This paper presents a study on the behavior of the self-excited switched reluctance generator (SSRG). Following an extensive bibliographic review about SSRGs, the mathematical model, principle of operation and simulation results of the generator dynamics is presented. A capacitor partially charged, in parallel with the load is used as a mean to provide the necessary amount of magnetic flux and start the generator's voltage built up. The arrangement is such that the generated voltage and current is delivered to the load in D.C. mode. To correctly represent the self excitation operation the mathematical model must take into account the core magnetic saturation, and that is observed here. Experimental results are included to validate the discussions presented.
- 1 May 2007
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- Vol. 13, 1171-1176
A Comparative Study Between Tree Philosophies of Stator Flux Estimation for Induction Motor Drive
This paper shows and compares three different flux estimator algorithms developed for use in high- performance sensorless ac motor drives. The first algorithm uses a low pass filter with a very low cut off frequency to integrate the back electromotive force (emf). The second one uses a high pass filter to remove the offset present in the signal before it's integration. The third algorithm uses current and voltage model to estimate the flux of induction motor. These algorithms can be used to accurately measure the motor flux including magnitude and phase angle over a wide speed range. The performance of the algorithms is investigated, compared, and verified using simulation. Preliminary experimental results are also included.
- 1 May 2007
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- Vol. 13, 1171-1176
A Comparative Study Between Tree Philosophies of Stator Flux Estimation for Induction Motor Drive
This paper shows and compares three different flux estimator algorithms developed for use in high- performance sensorless ac motor drives. The first algorithm uses a low pass filter with a very low cut off frequency to integrate the back electromotive force (emf). The second one uses a high pass filter to remove the offset present in the signal before it's integration. The third algorithm uses current and voltage model to estimate the flux of induction motor. These algorithms can be used to accurately measure the motor flux including magnitude and phase angle over a wide speed range. The performance of the algorithms is investigated, compared, and verified using simulation. Preliminary experimental results are also included.