Hajar Mohamadzade Sani
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Hajar Mohamadzade Sani has a total of 6 co-authors. Here are the top co-authors by number of shared publications:
- Seyed Mostafa Hosseinalipour
School of Mechanical Engineering, Iran University of Science and Technology, Tehran, Iran
3 shared publications - Ali Jawad Chamkha
Faculty of Engineering, Kuwait College of Science and Technology, Doha District, Kuwait
2 shared publications - Mohammad Nemati
Faculty of Mechanical Engineering, Yazd University, Yazd, Iran
2 shared publications - Koorosh Aieneh
CFD Lab and CAE Center, School of Mechanical Engineering, Iran University of Science & Technology, Tehran, Iran
1 shared publication - Ramin Jahangiri
Department of Mechanical Engineering, Urmia University, Urmia, Iran
1 shared publication - Sarah Salehi
School of Mechanical Engineering, Iran University of Science & Technology, Tehran, Iran
1 shared publication
Latest Publications
- 18 December 2025
- Published by IOP Publishing in Biomedical Physics & Engineering Express
- Vol. 12 (1) , 015025
A simple yet effective microfluidic device for the in-situ formation of uniform-sized cell-laden microgels
Alginate microgels are attractive platforms for cell encapsulation, yet conventional gelation strategies often lead to heterogeneous crosslinking, unstable droplets, and reduced cell viability. Here, we present a paraffin oil–based flow-focusing microfluidic system that integrates in situ and ex situ gelation to generate structurally homogeneous and monodisperse Ca-ALG microgels. Unlike conventional approaches that often suffer from unstable droplet formation or incomplete gelation, our method reliably produced uniform microgels with coefficients of variation consistently below 5% and maintained spherical morphology across a wide range of flow conditions. Scanning electron microscopy revealed a hierarchical porous architecture that supported nutrient and metabolite transport while providing structural stability. Encapsulated HEK-293 cells remained highly viable for more than two weeks, and spontaneous spheroid formation occurred within 24 h—an outcome rarely achieved in comparable systems and underscoring the functional relevance of this platform. Compared with existing microfluidic methods, this paraffin oil–driven dual gelation strategy offered superior reproducibility, droplet stability, and encapsulation efficiency. This study integrates and optimizes previously reported dual gelation strategies by employing paraffin oil in a flow-focusing device, establishing a simple, practical, and scalable solution to long-standing challenges in microgel-based encapsulation with strong potential to advance 3D culture, tissue engineering, and regenerative medicine.
- 18 December 2025
- Published by IOP Publishing in Biomedical Physics & Engineering Express
- Vol. 12 (1) , 015025
A simple yet effective microfluidic device for the in-situ formation of uniform-sized cell-laden microgels
Alginate microgels are attractive platforms for cell encapsulation, yet conventional gelation strategies often lead to heterogeneous crosslinking, unstable droplets, and reduced cell viability. Here, we present a paraffin oil–based flow-focusing microfluidic system that integrates in situ and ex situ gelation to generate structurally homogeneous and monodisperse Ca-ALG microgels. Unlike conventional approaches that often suffer from unstable droplet formation or incomplete gelation, our method reliably produced uniform microgels with coefficients of variation consistently below 5% and maintained spherical morphology across a wide range of flow conditions. Scanning electron microscopy revealed a hierarchical porous architecture that supported nutrient and metabolite transport while providing structural stability. Encapsulated HEK-293 cells remained highly viable for more than two weeks, and spontaneous spheroid formation occurred within 24 h—an outcome rarely achieved in comparable systems and underscoring the functional relevance of this platform. Compared with existing microfluidic methods, this paraffin oil–driven dual gelation strategy offered superior reproducibility, droplet stability, and encapsulation efficiency. This study integrates and optimizes previously reported dual gelation strategies by employing paraffin oil in a flow-focusing device, establishing a simple, practical, and scalable solution to long-standing challenges in microgel-based encapsulation with strong potential to advance 3D culture, tissue engineering, and regenerative medicine.
- Open Access
- 1 January 2025
- Published by KEAI Publishing in Biotechnology Notes
- Vol. 6, 230-244
CFD study and experimental verification of droplet formation characteristics in a flow-focusing microfluidic device
This study numerically investigates droplet formation in a three-dimensional flow-focusing microchannel and validates the results with a lithographically fabricated device (error ). The effects of injection angle, continuous phase viscosity, flow velocities, and interfacial tension on two-phase flow regimes, instantaneous flow fields, droplet size, formation frequency, and breakup time were examined. At acute angles, increasing the injection angle delays droplet detachment, producing larger droplets with greater interdroplet distance. At obtuse angles, larger injection angles slow down droplet formation and produce smaller droplets with shorter spacing. The injection angle of yields the maximum droplet diameter. As the flow rate ratio increases, the influence of the injection angle decreases, whereas higher capillary numbers amplify its effect. Higher continuous phase viscosity and velocity accelerate droplet formation, producing smaller droplets, while higher dispersed phase velocity and interfacial tension delay detachment, yielding larger droplets. Repeatability tests (coefficient of variation ) confirm high stability and reliability. These findings provide practical guidelines for designing controlled droplet generation in microfluidic applications.- 1 January 2025
- Published by KEAI Publishing in Biotechnology Notes
- Vol. 6, 230-244
Open AccessCFD study and experimental verification of droplet formation characteristics in a flow-focusing microfluidic device
This study numerically investigates droplet formation in a three-dimensional flow-focusing microchannel and validates the results with a lithographically fabricated device (error ). The effects of injection angle, continuous phase viscosity, flow velocities, and interfacial tension on two-phase flow regimes, instantaneous flow fields, droplet size, formation frequency, and breakup time were examined. At acute angles, increasing the injection angle delays droplet detachment, producing larger droplets with greater interdroplet distance. At obtuse angles, larger injection angles slow down droplet formation and produce smaller droplets with shorter spacing. The injection angle of yields the maximum droplet diameter. As the flow rate ratio increases, the influence of the injection angle decreases, whereas higher capillary numbers amplify its effect. Higher continuous phase viscosity and velocity accelerate droplet formation, producing smaller droplets, while higher dispersed phase velocity and interfacial tension delay detachment, yielding larger droplets. Repeatability tests (coefficient of variation ) confirm high stability and reliability. These findings provide practical guidelines for designing controlled droplet generation in microfluidic applications. - Open Access
- 18 November 2024
- Published by Springer Nature in Research Square
CFD study and Experimental Verification of droplet formation characteristics in a flow-focusing microfluidic device
Droplet-based microfluidics has received much attention today due to the precise control of droplet size and the uniform and integrated droplet production. In this paper, the droplet formation process in a three-dimensional geometry of a flow-focusing microfluidic device has been simulated by developing a code with the finite element method (FEM) and the two-phase level set method (LSM). Effective physical factors, including the continuous phase viscosity, two-phase flow velocities, interfacial tension and injection angle have been investigated on different parameters including the droplet generation mechanism, two-phase flow regimes, droplet size, droplet formation frequency and droplet breakup time to clarify the best conditions for the droplet formation with the desired shape and size. Based on the numerical model results, a flow-focusing microfluidic device has been fabricated with the same simulation dimensions under injection angle of \(\:\theta\:={90}^{^\circ\:}\) connection and evaluated using the lithography process. The simulation results accuracy has been validated by comparing with the experimental results. The relative error was less than \(\:4\%\) which shows that the experimental results and numerical model are in good agreement. Repeatability tests have been conducted as well and the standard deviation value and the coefficient of variation showed good repeatability and homogeneity in the produced droplets.- 18 November 2024
- Published by Springer Nature in Research Square
Open AccessCFD study and Experimental Verification of droplet formation characteristics in a flow-focusing microfluidic device
Droplet-based microfluidics has received much attention today due to the precise control of droplet size and the uniform and integrated droplet production. In this paper, the droplet formation process in a three-dimensional geometry of a flow-focusing microfluidic device has been simulated by developing a code with the finite element method (FEM) and the two-phase level set method (LSM). Effective physical factors, including the continuous phase viscosity, two-phase flow velocities, interfacial tension and injection angle have been investigated on different parameters including the droplet generation mechanism, two-phase flow regimes, droplet size, droplet formation frequency and droplet breakup time to clarify the best conditions for the droplet formation with the desired shape and size. Based on the numerical model results, a flow-focusing microfluidic device has been fabricated with the same simulation dimensions under injection angle of \(\:\theta\:={90}^{^\circ\:}\) connection and evaluated using the lithography process. The simulation results accuracy has been validated by comparing with the experimental results. The relative error was less than \(\:4\%\) which shows that the experimental results and numerical model are in good agreement. Repeatability tests have been conducted as well and the standard deviation value and the coefficient of variation showed good repeatability and homogeneity in the produced droplets. - 24 January 2022
- Published by Springer Nature in Journal of Thermal Analysis and Calorimetry
- Vol. 147 (16) , 9067-9081
MHD natural convection in a cavity with different geometries filled with a nanofluid in the presence of heat generation/absorption using lattice Boltzmann method
- 24 January 2022
- Published by Springer Nature in Journal of Thermal Analysis and Calorimetry
- Vol. 147 (16) , 9067-9081
MHD natural convection in a cavity with different geometries filled with a nanofluid in the presence of heat generation/absorption using lattice Boltzmann method
- 22 October 2021
- Published by IOP Publishing in Physica Scripta
- Vol. 96 (12) , 125234
Optimal wall natural convection for a non-Newtonian fluid with heat generation/absorption and magnetic field in a quarter-oval inclined cavity
For the first time, the present work investigates natural convection heat transfer in a two-dimensional inclined quarter-oval cavity filled with a non-Newtonian power-law fluid with heat generation/absorption in the presence of a magnetic field using the Lattice Boltzmann Method (LBM). Part of the vertical wall of the cavity is maintained at a constant hot temperature while the curved wall is kept at a constant cold temperature. All other walls are maintained adiabatic. The effect of physical parameters such as the Hartmann number, non-Newtonian power-law fluid index, heat generation/absorption coefficient and the inclination angle of the cavity on the nature of flow and heat transfer is studied and analyzed. The present work is validated with previous studies and the results are in very good agreement. The obtained results show that increasing the power-law fluid index on the average reduces the maximum value of the streamlines by 88% and the average Nusselt number by 45%. Also, increasing the Hartmann number reduces the heat transfer from the wall to the fluid. In the case of heat absorption and heat generation, the average Nusselt number is about 30% higher and 55% lower than in the case where there is no heat absorption/production, respectively. In addition, heat generation on the average increases the fluid flow power by 15%, which is negligible for the shear thickening fluid case. By increasing the heat generation/absorption coefficient and decreasing the non-Newtonian power-law fluid index, the effect of the magnetic field increases. The lowest amount of heat transfer is observed at a 90 degrees inclination angle of the cavity for which the average Nusselt number is up to about 10% less in this case. In the absence of a magnetic field and at a 180 degrees inclination angle, the maximum amount of heat transfer from the wall to the fluid is observed for a non-Newtonian shear thinning fluid and for heat absorption. This study could pave the way for the optimal design of industrial thermal equipment.
- 22 October 2021
- Published by IOP Publishing in Physica Scripta
- Vol. 96 (12) , 125234
Optimal wall natural convection for a non-Newtonian fluid with heat generation/absorption and magnetic field in a quarter-oval inclined cavity
For the first time, the present work investigates natural convection heat transfer in a two-dimensional inclined quarter-oval cavity filled with a non-Newtonian power-law fluid with heat generation/absorption in the presence of a magnetic field using the Lattice Boltzmann Method (LBM). Part of the vertical wall of the cavity is maintained at a constant hot temperature while the curved wall is kept at a constant cold temperature. All other walls are maintained adiabatic. The effect of physical parameters such as the Hartmann number, non-Newtonian power-law fluid index, heat generation/absorption coefficient and the inclination angle of the cavity on the nature of flow and heat transfer is studied and analyzed. The present work is validated with previous studies and the results are in very good agreement. The obtained results show that increasing the power-law fluid index on the average reduces the maximum value of the streamlines by 88% and the average Nusselt number by 45%. Also, increasing the Hartmann number reduces the heat transfer from the wall to the fluid. In the case of heat absorption and heat generation, the average Nusselt number is about 30% higher and 55% lower than in the case where there is no heat absorption/production, respectively. In addition, heat generation on the average increases the fluid flow power by 15%, which is negligible for the shear thickening fluid case. By increasing the heat generation/absorption coefficient and decreasing the non-Newtonian power-law fluid index, the effect of the magnetic field increases. The lowest amount of heat transfer is observed at a 90 degrees inclination angle of the cavity for which the average Nusselt number is up to about 10% less in this case. In the absence of a magnetic field and at a 180 degrees inclination angle, the maximum amount of heat transfer from the wall to the fluid is observed for a non-Newtonian shear thinning fluid and for heat absorption. This study could pave the way for the optimal design of industrial thermal equipment.