Suli Li
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Suli Li has a total of 32 co-authors. Here are the top co-authors by number of shared publications:
- Laixia Yang
School of Mechanical Engineering, Xi’an University of Science and Technology, Xi’an 710054, China
4 shared publications - Chao Xu
College of Mechanical Engineering, Xi’an University of Science and Technology, Xi’an 710054, China
3 shared publications - Bingheng Lu
National Innovation Institute of Additive Manufacturing, Xi’an 710300, China
2 shared publications - Jichao Chen
School of Mechanical Engineering, Xi’an University of Science and Technology, Xi’an 710054, China
2 shared publications - Jie Xiong
School of Mechanical Engineering, Xi’an University of Science and Technology, Xi’an 710054, China
2 shared publications - Kaiyue Ma
School of Mechanical Engineering, Xi’an University of Science and Technology, Xi’an 710054, China
2 shared publications
Latest Publications
- Open Access
- 7 July 2026
- Published by Springer Nature in Scientific Reports
- Vol. 16 (1)
Joule-Heated direct writing: an electrically-driven additive manufacturing paradigm for space fabrication
The imperative for in-space manufacturing drives the development of compact, energy-efficient metal additive manufacturing (AM) technologies. This work introduces and investigates a novel Joule-Heating Additive Manufacturing (JHAM) process, inspired by the Joule-Lenz effect, for the direct writing of metallic structures. A fully coupled thermal-electrical-structural finite element model is developed to simulate the multilayer deposition of 304 stainless steel wire, elucidating the unique "tusk-shaped" temperature field evolution and the effects of current, speed, and contact width. Single-bead, five-layer walls are fabricated experimentally, and the influence of process parameters on macrostructure, geometry (width, height, overlap rate), surface roughness (Ra, Rz), and cross-sectional hardness is systematically characterized. The results demonstrate that optimal macroscopic quality is achieved at 120 A, 200 mm/min, and a 1.0 mm contact width. The forming width and overlap rate increase with current, while the forming height decreases; conversely, increasing speed reduces width and overlap but increases height. Surface roughness and hardness exhibit non-monotonic trends with varying parameters, with a minimum Ra of 0.142 µm attained. Simulated and experimentally measured voltages show good agreement, validating the multiphysics model.Validation results indicate a voltage discrepancy of less than 10% between simulation and experiment. The JHAM process, with its low power consumption (<1 kW) and simplified architecture, presents a promising candidate for on-orbit fabrication of metallic components.
- 7 July 2026
- Published by Springer Nature in Scientific Reports
- Vol. 16 (1)
Open AccessJoule-Heated direct writing: an electrically-driven additive manufacturing paradigm for space fabrication
The imperative for in-space manufacturing drives the development of compact, energy-efficient metal additive manufacturing (AM) technologies. This work introduces and investigates a novel Joule-Heating Additive Manufacturing (JHAM) process, inspired by the Joule-Lenz effect, for the direct writing of metallic structures. A fully coupled thermal-electrical-structural finite element model is developed to simulate the multilayer deposition of 304 stainless steel wire, elucidating the unique "tusk-shaped" temperature field evolution and the effects of current, speed, and contact width. Single-bead, five-layer walls are fabricated experimentally, and the influence of process parameters on macrostructure, geometry (width, height, overlap rate), surface roughness (Ra, Rz), and cross-sectional hardness is systematically characterized. The results demonstrate that optimal macroscopic quality is achieved at 120 A, 200 mm/min, and a 1.0 mm contact width. The forming width and overlap rate increase with current, while the forming height decreases; conversely, increasing speed reduces width and overlap but increases height. Surface roughness and hardness exhibit non-monotonic trends with varying parameters, with a minimum Ra of 0.142 µm attained. Simulated and experimentally measured voltages show good agreement, validating the multiphysics model.Validation results indicate a voltage discrepancy of less than 10% between simulation and experiment. The JHAM process, with its low power consumption (<1 kW) and simplified architecture, presents a promising candidate for on-orbit fabrication of metallic components.
- Open Access
Fused Deposition Modeling and Mechanical Properties of Porous Titanium Scaffolds
To address issues such as thermal stress concentration in metal bone implants produced via high-energy beam direct additive manufacturing, a method was proposed to fabricate porous titanium scaffolds. This approach combined Fused Deposition Modeling (FDM) with a debinding–sintering process. Ti/ABS composite filaments with titanium volume fractions of 35%, 40%, and 45% were successfully developed via a single-screw extrusion process. Their feasibility in the FDM process was subsequently verified. The effects of different processing parameters on the forming quality and dimensional accuracy of the green bodies were investigated. After debinding and sintering the composite scaffolds prepared with optimized parameters, structurally intact porous titanium scaffolds were obtained. Microscopic characterization shows that the scaffold surface consists primarily of titanium, and the pore structure remains intact. Furthermore, compression tests were performed on three types of porous titanium scaffolds with different porosities. The results indicate that the combination of ABS/titanium alloy composite filaments, FDM technology, and debinding–sintering post-processing enables the high-quality and efficient production of porous titanium scaffolds. The elastic modulus of the resulting scaffolds ranges from 1.2 to 1.6 GPa, and the compressive strength is between 25.7 and 68.3 MPa. The elastic modulus matches that of human cancellous bone. Meanwhile, the compressive strength is significantly higher than that of cancellous bone and falls between the values for cancellous and cortical bone. These mechanical properties meet the requirements for human bone, providing a new approach for the manufacture of orthopedic implants.
Open AccessFused Deposition Modeling and Mechanical Properties of Porous Titanium Scaffolds
To address issues such as thermal stress concentration in metal bone implants produced via high-energy beam direct additive manufacturing, a method was proposed to fabricate porous titanium scaffolds. This approach combined Fused Deposition Modeling (FDM) with a debinding–sintering process. Ti/ABS composite filaments with titanium volume fractions of 35%, 40%, and 45% were successfully developed via a single-screw extrusion process. Their feasibility in the FDM process was subsequently verified. The effects of different processing parameters on the forming quality and dimensional accuracy of the green bodies were investigated. After debinding and sintering the composite scaffolds prepared with optimized parameters, structurally intact porous titanium scaffolds were obtained. Microscopic characterization shows that the scaffold surface consists primarily of titanium, and the pore structure remains intact. Furthermore, compression tests were performed on three types of porous titanium scaffolds with different porosities. The results indicate that the combination of ABS/titanium alloy composite filaments, FDM technology, and debinding–sintering post-processing enables the high-quality and efficient production of porous titanium scaffolds. The elastic modulus of the resulting scaffolds ranges from 1.2 to 1.6 GPa, and the compressive strength is between 25.7 and 68.3 MPa. The elastic modulus matches that of human cancellous bone. Meanwhile, the compressive strength is significantly higher than that of cancellous bone and falls between the values for cancellous and cortical bone. These mechanical properties meet the requirements for human bone, providing a new approach for the manufacture of orthopedic implants.
- Open Access
Numerical Simulation and Experimental Study on the Influence of Scanning Strategy on Stress–Strain Behavior of GH3536 in Laser Powder Bed Fusion
High residual stresses significantly impact component performance during laser powder bed fusion (L-PBF) of GH3536 alloy. This study systematically investigates the effects of five scanning strategies (X-Scan, XY-Scan, R67, CB90, CB67) on residual stresses and deformation behavior in laser powder bed fusion-formed GH3536 high-temperature alloy. This is achieved by establishing a thermomechanically coupled mesoscale finite element model and combining it with experimental validation. The model was developed on the ANSYS APDL platform using a sequential coupling algorithm. It comprehensively considered melting latent heat, material nonlinearity, and dead-body element technology. While ensuring computational accuracy, significant computational efficiency gains were achieved through geometric scaling and reasonable simplifications (e.g., neglecting evaporation effects and assuming material isotropy). Results indicate that the 67° interlayer rotational scanning (R67) significantly reduces residual stresses, attributed to the breaking of thermal accumulation symmetry by asymmetric scanning. Component deformation is primarily governed by thermal stresses, with simulation results showing less than 10% deviation from experimental measurements. Despite the model’s medium-to-small scale and omission of size effects, its predicted trends highly correlate with X-ray diffraction measurements, validating its reliability for scan strategy optimization. Electron backscatter diffraction (EBSD) analysis further examined grain size and orientation differences at the microstructural level under the R67 strategy, revealing a more refined grain structure and KAM values. This provides theoretical support for L-PBF forming of nickel-based high-temperature alloys.
Open AccessNumerical Simulation and Experimental Study on the Influence of Scanning Strategy on Stress–Strain Behavior of GH3536 in Laser Powder Bed Fusion
High residual stresses significantly impact component performance during laser powder bed fusion (L-PBF) of GH3536 alloy. This study systematically investigates the effects of five scanning strategies (X-Scan, XY-Scan, R67, CB90, CB67) on residual stresses and deformation behavior in laser powder bed fusion-formed GH3536 high-temperature alloy. This is achieved by establishing a thermomechanically coupled mesoscale finite element model and combining it with experimental validation. The model was developed on the ANSYS APDL platform using a sequential coupling algorithm. It comprehensively considered melting latent heat, material nonlinearity, and dead-body element technology. While ensuring computational accuracy, significant computational efficiency gains were achieved through geometric scaling and reasonable simplifications (e.g., neglecting evaporation effects and assuming material isotropy). Results indicate that the 67° interlayer rotational scanning (R67) significantly reduces residual stresses, attributed to the breaking of thermal accumulation symmetry by asymmetric scanning. Component deformation is primarily governed by thermal stresses, with simulation results showing less than 10% deviation from experimental measurements. Despite the model’s medium-to-small scale and omission of size effects, its predicted trends highly correlate with X-ray diffraction measurements, validating its reliability for scan strategy optimization. Electron backscatter diffraction (EBSD) analysis further examined grain size and orientation differences at the microstructural level under the R67 strategy, revealing a more refined grain structure and KAM values. This provides theoretical support for L-PBF forming of nickel-based high-temperature alloys.
- 8 February 2025
- Published by Elsevier in Computers in Biology and Medicine
- Vol. 187, 109796
Structural design and mechanical performance evaluation of personalized irregular porous L3-L4 fusion cage by additive manufacturing
- 8 February 2025
- Published by Elsevier in Computers in Biology and Medicine
- Vol. 187, 109796
Structural design and mechanical performance evaluation of personalized irregular porous L3-L4 fusion cage by additive manufacturing
- Open Access
The Influence of Process Parameters on the Microstructure and Microhardness of 304 Stainless Steel in Joule Heating Fused Filament Fabrication
Using finite element simulation and single-variable experimental methods, this study analyzes the variations in the microstructure and hardness of a 304 stainless steel wire during Joule heating fused filament fabrication. The effects of current intensity, printing speed, and roller pressure on the macroscopic morphology, microstructure, and microhardness of a single-layer single-channel formation were investigated. The results indicate that when the current intensity is 400 A, the printing speed is 1000 mm/min, and the roller pressure is 0.3 N, the surface of the single-layer single-channel formation is smooth and exhibits optimal forming characteristics with a width-to-height ratio of 3.23, a dilution rate of 51.61%, and an average microhardness of 238.17 HV. As the current intensity increases, the microstructure in the fusion zone initially decreases in size and then increases; similarly, with the increase in printing speed, the microstructure in the fusion zone first decreases and then increases; as the roller pressure increases, the microstructure in the fusion zone initially increases in size and then decreases. The microhardness initially increases and then decreases with the increase in process parameters, resulting in uneven hardness distribution due to the variations in microstructure size. The optimal combination of process parameters achieves a balance between heat input, cooling rate, and growth rate, thereby achieving grain refinement and hardness improvement, ultimately enhancing the mechanical properties of the material.
Open AccessThe Influence of Process Parameters on the Microstructure and Microhardness of 304 Stainless Steel in Joule Heating Fused Filament Fabrication
Using finite element simulation and single-variable experimental methods, this study analyzes the variations in the microstructure and hardness of a 304 stainless steel wire during Joule heating fused filament fabrication. The effects of current intensity, printing speed, and roller pressure on the macroscopic morphology, microstructure, and microhardness of a single-layer single-channel formation were investigated. The results indicate that when the current intensity is 400 A, the printing speed is 1000 mm/min, and the roller pressure is 0.3 N, the surface of the single-layer single-channel formation is smooth and exhibits optimal forming characteristics with a width-to-height ratio of 3.23, a dilution rate of 51.61%, and an average microhardness of 238.17 HV. As the current intensity increases, the microstructure in the fusion zone initially decreases in size and then increases; similarly, with the increase in printing speed, the microstructure in the fusion zone first decreases and then increases; as the roller pressure increases, the microstructure in the fusion zone initially increases in size and then decreases. The microhardness initially increases and then decreases with the increase in process parameters, resulting in uneven hardness distribution due to the variations in microstructure size. The optimal combination of process parameters achieves a balance between heat input, cooling rate, and growth rate, thereby achieving grain refinement and hardness improvement, ultimately enhancing the mechanical properties of the material.
- Open Access
Study on Single-Layer and Single-Channel Microstructure of 304 Stainless Steel Using Joule Heat Additive Manufacturing
In this study, a solution to the issue of a large heat-affected zone in Wire Arc Additive Manufacturing is presented by employing the Joule Heat Additive Manufacturing method to create a single layer and single channel with a reduced heat-affected zone. The microstructure of the single layer and single channel is thoroughly investigated using various detection methods, including optical microscopy (OM), scanning electron microscopy (SEM), energy-dispersive spectroscopy (EDS), and electron backscatter diffraction (EBSD). The results reveal that the heat-affected zone formed by the Joule Heat Additive Manufacturing method is smaller than that produced by the Wire Arc Additive Manufacturing method. Additionally, the grains in the single layer and single channel progress from planar to columnar, then equiaxed, and finally back to columnar from the fusion line to the top of the wire. The element content and distribution are relatively uniform. The microstructure of the single layer consists of austenite and a small amount of ferrite, with austenite accounting for 99.71% of the content. The grain size in the middle of the wire is mainly around 10 μm, with the smallest angle grain boundaries within 10°. The distribution of local grain orientation differences in the three regions is found to be largely consistent. The analysis of the microstructure of the single layer and single channel serves as a valuable reference for understanding the behavior of single-channel multi-layers in future studies.
Open AccessStudy on Single-Layer and Single-Channel Microstructure of 304 Stainless Steel Using Joule Heat Additive Manufacturing
In this study, a solution to the issue of a large heat-affected zone in Wire Arc Additive Manufacturing is presented by employing the Joule Heat Additive Manufacturing method to create a single layer and single channel with a reduced heat-affected zone. The microstructure of the single layer and single channel is thoroughly investigated using various detection methods, including optical microscopy (OM), scanning electron microscopy (SEM), energy-dispersive spectroscopy (EDS), and electron backscatter diffraction (EBSD). The results reveal that the heat-affected zone formed by the Joule Heat Additive Manufacturing method is smaller than that produced by the Wire Arc Additive Manufacturing method. Additionally, the grains in the single layer and single channel progress from planar to columnar, then equiaxed, and finally back to columnar from the fusion line to the top of the wire. The element content and distribution are relatively uniform. The microstructure of the single layer consists of austenite and a small amount of ferrite, with austenite accounting for 99.71% of the content. The grain size in the middle of the wire is mainly around 10 μm, with the smallest angle grain boundaries within 10°. The distribution of local grain orientation differences in the three regions is found to be largely consistent. The analysis of the microstructure of the single layer and single channel serves as a valuable reference for understanding the behavior of single-channel multi-layers in future studies.
- Open Access
The Research on Ultrasonic Vibration Amplitudes in Ti6Al4V DED Additive Manufacturing
Ultrasonic-assisted Ti6Al4V Directed Energy Deposition (DED) additive manufacturing technology can improve the problem of uneven microstructure caused by laser heating and sudden cooling of the molten pool. In this paper, the numerical analysis and experimental verification methods were adopted. The influencing factors, such as the cavitations’ effect, sound flow enhancement effect, and sound flow thermal effect related to the ultrasonic assistance in the molten pool, were analyzed. After equating the energy of the ultrasound, the model of additive manufacturing was introduced in the form of a heat source. The temperature gradient changes during the solidification process of the molten pool with the addition of ultrasound assistance and the effect of ultrasonic vibration during the manufacturing process on its deposited state and microstructure of solution-aged formed parts were studied. The results showed that when the wire feeding rate is 5 mm/s and the laser scanning speed is 5 mm/s, the optimal laser power is 1000 W~1100 W, corresponding to the optimal ultrasonic amplitude of 120 μm. Then, by comparing the temperature field with the same amplitude of 0 μm (i.e., no ultrasonic vibration) and the microstructure of the formed parts, it was verified that ultrasonic vibration facilitates fluid flow in the molten pool, which could lead to a more uniform temperature distribution. This optimized approach not only enhances the understanding of the process but also contributes significantly to the advancement of related research endeavors.
Open AccessThe Research on Ultrasonic Vibration Amplitudes in Ti6Al4V DED Additive Manufacturing
Ultrasonic-assisted Ti6Al4V Directed Energy Deposition (DED) additive manufacturing technology can improve the problem of uneven microstructure caused by laser heating and sudden cooling of the molten pool. In this paper, the numerical analysis and experimental verification methods were adopted. The influencing factors, such as the cavitations’ effect, sound flow enhancement effect, and sound flow thermal effect related to the ultrasonic assistance in the molten pool, were analyzed. After equating the energy of the ultrasound, the model of additive manufacturing was introduced in the form of a heat source. The temperature gradient changes during the solidification process of the molten pool with the addition of ultrasound assistance and the effect of ultrasonic vibration during the manufacturing process on its deposited state and microstructure of solution-aged formed parts were studied. The results showed that when the wire feeding rate is 5 mm/s and the laser scanning speed is 5 mm/s, the optimal laser power is 1000 W~1100 W, corresponding to the optimal ultrasonic amplitude of 120 μm. Then, by comparing the temperature field with the same amplitude of 0 μm (i.e., no ultrasonic vibration) and the microstructure of the formed parts, it was verified that ultrasonic vibration facilitates fluid flow in the molten pool, which could lead to a more uniform temperature distribution. This optimized approach not only enhances the understanding of the process but also contributes significantly to the advancement of related research endeavors.
- Open Access
Study on the Process Characteristics Based on Joule Heat of Sliding-Pressure Additive Manufacturing
This study developed an experimental system based on Joule heat of sliding-pressure additive manufacturing (SP-JHAM), and Joule heat was used for the first time to accomplish high-quality single-layer printing. The roller wire substrate is short-circuited, and Joule heat is generated to melt the wire when the current passes through. Through the self-lapping experimental platform, single-factor experiments were designed to study the effects of power supply current, electrode pressure, contact length on the surface morphology and cross-section geometric characteristics of the single-pass printing layer. Through the Taguchi method, the effect of various factors was analyzed, the optimal process parameters were obtained, and the quality was detected. The results show that with the current increase, the aspect ratio and dilution rate of a printing layer increase within a given range of process parameters. In addition, with the increase in pressure and contact length, the aspect ratio and dilution ratio decrease. Pressure has the greatest effect on the aspect ratio and dilution ratio, followed by current and contact length. When a current of 260 A, a pressure of 0.60 N and a contact length of 1.3 mm are applied, a single track with a good appearance, whose surface roughness Ra is 3.896 μm, can be printed. Additionally, the wire and the substrate are completely metallurgically bonded with this condition. There are also no defects such as air holes and cracks. This study verified the feasibility of SP-JHAM as a new additive manufacturing strategy with high quality and low cost, and provided a reference for developing additive manufacturing technology based on Joule heat.
Open AccessStudy on the Process Characteristics Based on Joule Heat of Sliding-Pressure Additive Manufacturing
This study developed an experimental system based on Joule heat of sliding-pressure additive manufacturing (SP-JHAM), and Joule heat was used for the first time to accomplish high-quality single-layer printing. The roller wire substrate is short-circuited, and Joule heat is generated to melt the wire when the current passes through. Through the self-lapping experimental platform, single-factor experiments were designed to study the effects of power supply current, electrode pressure, contact length on the surface morphology and cross-section geometric characteristics of the single-pass printing layer. Through the Taguchi method, the effect of various factors was analyzed, the optimal process parameters were obtained, and the quality was detected. The results show that with the current increase, the aspect ratio and dilution rate of a printing layer increase within a given range of process parameters. In addition, with the increase in pressure and contact length, the aspect ratio and dilution ratio decrease. Pressure has the greatest effect on the aspect ratio and dilution ratio, followed by current and contact length. When a current of 260 A, a pressure of 0.60 N and a contact length of 1.3 mm are applied, a single track with a good appearance, whose surface roughness Ra is 3.896 μm, can be printed. Additionally, the wire and the substrate are completely metallurgically bonded with this condition. There are also no defects such as air holes and cracks. This study verified the feasibility of SP-JHAM as a new additive manufacturing strategy with high quality and low cost, and provided a reference for developing additive manufacturing technology based on Joule heat.
- Open Access
Numerical Analysis and Experimental Verification of Resistance Additive Manufacturing
In recent years, scholars have proposed a metal wire forming method based on the Joule heat principle in order to improve the accuracy of additive manufacturing and reduce energy consumption and cost, but it is still in the theoretical stage. In this paper, a mathematical model of resistance additive manufacturing was established using finite element software, and the temperature variation of the melting process under different currents was analyzed. A suitable current range was preliminarily selected, and an experimental system was built. Through experimental study of the current and wire feeding speed, the influences of different process parameters on the forming appearance of the coating were analyzed. The results showed that the forming appearance was the best for Ti-6Al-4V titanium alloy wire with a diameter of 0.8 mm, when the current was 160 A, the voltage was 10 V, the wire feeding speed was 2.4 m/min, the workbench moving speed was 5 mm/s, and the gas flow rate was 0.7 m3/h. Finally, the process parameters were used for continuous single-channel multilayer printing, verified the feasibility of the process at the experimental level and provided reference data for the subsequent development of this technology.
Open AccessNumerical Analysis and Experimental Verification of Resistance Additive Manufacturing
In recent years, scholars have proposed a metal wire forming method based on the Joule heat principle in order to improve the accuracy of additive manufacturing and reduce energy consumption and cost, but it is still in the theoretical stage. In this paper, a mathematical model of resistance additive manufacturing was established using finite element software, and the temperature variation of the melting process under different currents was analyzed. A suitable current range was preliminarily selected, and an experimental system was built. Through experimental study of the current and wire feeding speed, the influences of different process parameters on the forming appearance of the coating were analyzed. The results showed that the forming appearance was the best for Ti-6Al-4V titanium alloy wire with a diameter of 0.8 mm, when the current was 160 A, the voltage was 10 V, the wire feeding speed was 2.4 m/min, the workbench moving speed was 5 mm/s, and the gas flow rate was 0.7 m3/h. Finally, the process parameters were used for continuous single-channel multilayer printing, verified the feasibility of the process at the experimental level and provided reference data for the subsequent development of this technology.