Sreeram Hariharan
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Sreeram Hariharan has a total of 11 co-authors. Here are the top co-authors by number of shared publications:
- Marimuthu Uthayakumar
Department of Mechanical Engineering, Center for Flexible Electronics & Advanced Materials, Amrita Vishwa Vidyapeetham, Amritapuri, Kollam 690525, Kerala, India
3 shared publications - Kinga Korniejenko
Cracow University of Technology
2 shared publications - Shanmugam Suresh Kumar
Kalasalingam Academy of Research and Education
2 shared publications - Sundaresan Thirumalai Kumaran
Department of Mechanical Engineering, PSG Institute of Technology and Applied Research, Coimbatore 641062, Tamil Nadu, India
2 shared publications - Brian Azzopardi
MCAST Energy Research Group, Institute for Engineering and Transport, Malta College of Arts, Science and Technology (MCAST), PLA 9032 Paola, Malta
1 shared publication Darius Mierzwinshi
Faculty Material Engineering and Physics, Cracow University of Technology, 30010, Poland
1 shared publication
Latest Publications
- Open Access
- 6 December 2023
- Published by Rangsit University in Journal of Current Science and Technology
- Vol. 14 (1)
Wire Electric Discharge Machining of Aluminium Hybrid Composite: Renewable Energy Based IoT Approach
Wire Electric Discharge Machining (WEDM) has been recognized as one of the optimum methods for machining of harder aluminum-based hybrid metal matrix composites (AHMMC). This method is used to optimize the major control aspects of a machine and they are current, pulse duration, and rate of feed of wire on kerf width (KRW) and Surface roughness (Ra) of hybrid composites made of aluminum Al6351 as the metal matrix (AMMHC). The AMMHC has been created via a stir casting technique by adding SiC and B4C with an Al6351 matrix. Box-Behnken design (BBD) has been used to conduct tests in order to parametrically optimize the WEDM process. The optimization of KRW and Ra is identified using 3-D surface plots, graphs and response table of ANOVA as well as by employing Response Surface Methodology (RSM). Internet of Things (IoT) is implemented to monitor the quality of electrolyte that is used in WEDM. It has been identified that the current has a major contribution in both KRW and Ra factors. A lower current is preferred for a lower KRW whereas higher current improves Ra value.
- 6 December 2023
- Published by Rangsit University in Journal of Current Science and Technology
- Vol. 14 (1)
Open AccessWire Electric Discharge Machining of Aluminium Hybrid Composite: Renewable Energy Based IoT Approach
Wire Electric Discharge Machining (WEDM) has been recognized as one of the optimum methods for machining of harder aluminum-based hybrid metal matrix composites (AHMMC). This method is used to optimize the major control aspects of a machine and they are current, pulse duration, and rate of feed of wire on kerf width (KRW) and Surface roughness (Ra) of hybrid composites made of aluminum Al6351 as the metal matrix (AMMHC). The AMMHC has been created via a stir casting technique by adding SiC and B4C with an Al6351 matrix. Box-Behnken design (BBD) has been used to conduct tests in order to parametrically optimize the WEDM process. The optimization of KRW and Ra is identified using 3-D surface plots, graphs and response table of ANOVA as well as by employing Response Surface Methodology (RSM). Internet of Things (IoT) is implemented to monitor the quality of electrolyte that is used in WEDM. It has been identified that the current has a major contribution in both KRW and Ra factors. A lower current is preferred for a lower KRW whereas higher current improves Ra value.
- Open Access
- 4 March 2022
- Published by MDPI AG in Applied Sciences
- Vol. 12 (5) , 2673
Modelling Approach for the Prediction of Machinability in Al6061 Composites by Electrical Discharge Machining
This work aims to identify the pattern for the major output parameters, material removal rate (MRR) and surface roughness (Ra) of different combinations of Al6061-based composites. Based on the verification carried out on these patterns using analysis of variance (ANOVA) as the mathematical tool, the work predicts the mentioned output characteristics while machining Al6061 composites of different material compositions based on their hardness values. ANOVA was employed for the generation of equations of the particular composite. The equations were compared for the coefficients of each parameter employed in ANOVA. The work was carried out comparing the characteristic equation of different combinations of Al6061-based composite. The results indicate that the coefficients of the current show a drastic variation when compared to other coefficients for both the output parameters. It was observed that the current and its coefficients contribute to the output parameters based on the variation in hardness. For surface roughness, the constant of the characteristic equation was also found to influence the parameter for the change in hardness. The equation derived for both material removal rate (MRR) and surface roughness (Ra) were identified to be matching with the experimental result carried out for validation. The average variation observed was 9.3% for MRR and 7.2% for surface roughness.
- 4 March 2022
- Published by MDPI AG in Applied Sciences
- Vol. 12 (5) , 2673
Open AccessModelling Approach for the Prediction of Machinability in Al6061 Composites by Electrical Discharge Machining
This work aims to identify the pattern for the major output parameters, material removal rate (MRR) and surface roughness (Ra) of different combinations of Al6061-based composites. Based on the verification carried out on these patterns using analysis of variance (ANOVA) as the mathematical tool, the work predicts the mentioned output characteristics while machining Al6061 composites of different material compositions based on their hardness values. ANOVA was employed for the generation of equations of the particular composite. The equations were compared for the coefficients of each parameter employed in ANOVA. The work was carried out comparing the characteristic equation of different combinations of Al6061-based composite. The results indicate that the coefficients of the current show a drastic variation when compared to other coefficients for both the output parameters. It was observed that the current and its coefficients contribute to the output parameters based on the variation in hardness. For surface roughness, the constant of the characteristic equation was also found to influence the parameter for the change in hardness. The equation derived for both material removal rate (MRR) and surface roughness (Ra) were identified to be matching with the experimental result carried out for validation. The average variation observed was 9.3% for MRR and 7.2% for surface roughness.
- Open Access
Prediction of Kerf Width and Surface Roughness of Al6351 Based Composite in Wire-Cut Electric Discharge Machining Using Mathematical Modelling
The machining of composite materials has been an area of intense research for the past couple of decades due to its wide range of applications, from automobiles to air crafts or from boats to nuclear systems. Non-conventional machining, especially electric discharge machining (EDM), is found to be a good machining option for meeting the required outputs. To overcome the challenges of machining complex shapes, wire electric discharge machining (WEDM) was developed. Al6351 composites was observed to be extensively used in nuclear applications. Therefore, identifying the kerf width and surface roughness are important criteria for the dimensional accuracy of the final product. The present work aims at predicting the behavior of the two major machining parameters which are kerf width and surface roughness of Al6351 composites in wire EDM by creating a mathematical model using ANOVA for different combinations of the reinforcements and comparing the variations in the coefficients for different combinations of reinforcements. The developed model has been validated by conducting similar set of experiments in Al6351-5% SiC-1% B4C hybrid composite. From the work, it was identified that pulse on time and current are the major contributing factor for kerf width and wire feed rate was observed to be contributing to the surface roughness. The validation results show an average variation of 8.17% for kerf width and 11.27% for surface roughness. The work can be successfully utilized for prediction of the kerf width and surface roughness of the composites manufactured with Al6351 as the base matrix material.
Open AccessPrediction of Kerf Width and Surface Roughness of Al6351 Based Composite in Wire-Cut Electric Discharge Machining Using Mathematical Modelling
The machining of composite materials has been an area of intense research for the past couple of decades due to its wide range of applications, from automobiles to air crafts or from boats to nuclear systems. Non-conventional machining, especially electric discharge machining (EDM), is found to be a good machining option for meeting the required outputs. To overcome the challenges of machining complex shapes, wire electric discharge machining (WEDM) was developed. Al6351 composites was observed to be extensively used in nuclear applications. Therefore, identifying the kerf width and surface roughness are important criteria for the dimensional accuracy of the final product. The present work aims at predicting the behavior of the two major machining parameters which are kerf width and surface roughness of Al6351 composites in wire EDM by creating a mathematical model using ANOVA for different combinations of the reinforcements and comparing the variations in the coefficients for different combinations of reinforcements. The developed model has been validated by conducting similar set of experiments in Al6351-5% SiC-1% B4C hybrid composite. From the work, it was identified that pulse on time and current are the major contributing factor for kerf width and wire feed rate was observed to be contributing to the surface roughness. The validation results show an average variation of 8.17% for kerf width and 11.27% for surface roughness. The work can be successfully utilized for prediction of the kerf width and surface roughness of the composites manufactured with Al6351 as the base matrix material.
- 14 August 2020
- Published by Taylor & Francis
- p. 557-560
Mathematical Modeling of Cutting Force and Surface Roughness Analysis During Cutting Operation of Al 7075 Based Hybrid Composites
The machining of hybrid metal matrix composites has been one of the biggest challenges observed in the manufacturing industry. The machining process needs to be optimized to obtain the best output parameters for most of the input parameters, which poses a biggest challenge for the researchers. This work aims at producing a mathematical modeling and Analysis of Variance for the optimization of cutting force and surface roughness of Al 7075 uncoated composite. It also aims at understanding the effect of interactions on the output parameters of the material.
- 14 August 2020
- Published by Taylor & Francis
- p. 557-560
Mathematical Modeling of Cutting Force and Surface Roughness Analysis During Cutting Operation of Al 7075 Based Hybrid Composites
The machining of hybrid metal matrix composites has been one of the biggest challenges observed in the manufacturing industry. The machining process needs to be optimized to obtain the best output parameters for most of the input parameters, which poses a biggest challenge for the researchers. This work aims at producing a mathematical modeling and Analysis of Variance for the optimization of cutting force and surface roughness of Al 7075 uncoated composite. It also aims at understanding the effect of interactions on the output parameters of the material.