Mohd Ahtesham Hussain Siddiqui
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Mohd Ahtesham Hussain Siddiqui has a total of 37 co-authors. Here are the top co-authors by number of shared publications:
- Shubham Sharma
Department of Technical Sciences, Western Caspian University, Baku, Azerbaijan; Centre for Research Impact and Outcome, Chitkara University Institute of Engineering and Technology, Chitkara University, Rajpura 140401 Punjab, India; Jadara University Research Center, Jadara University, Jordan
6 shared publications - Somnath Chattopadhyaya
Department of Mechanical Engineering, Indian Institute of Technology (Indian School of Mines), Dhanbad, India
6 shared publications - Piush Raj
L & T Technology Services Limited Vadodara, Vadodara, India
5 shared publications - Saurabh Dewangan
Department of Mechanical Engineering, Manipal University Jaipur, Jaipur, India
5 shared publications - Shahzad Akhtar
Coal India Limited, Western Coal Fields Limited, Saoner, India
4 shared publications - Mamdouh El Haj Assad
University of Sharjah
3 shared publications
Latest Publications
- Open Access
- 20 October 2026
- Published by Springer Nature in Discover Applied Sciences
A hybrid physics–statistics–machine learning framework for reliability optimization of repairable Load Haul Dumper equipment
- 20 October 2026
- Published by Springer Nature in Discover Applied Sciences
Open AccessA hybrid physics–statistics–machine learning framework for reliability optimization of repairable Load Haul Dumper equipment
- Open Access
- 9 June 2026
- Published by Elsevier in Results in Engineering
- Vol. 31
Energy, exergy, and environmental (3E) analysis of transcritical CO2 refrigeration cycle with an expander, an internal heat exchanger, and a mechanical sub-cooler
- 9 June 2026
- Published by Elsevier in Results in Engineering
- Vol. 31
Open AccessEnergy, exergy, and environmental (3E) analysis of transcritical CO2 refrigeration cycle with an expander, an internal heat exchanger, and a mechanical sub-cooler
- 19 September 2025
- Published by Springer Nature in Mining, Metallurgy & Exploration
- Vol. 42 (5) , 3055-3072
Reliability, Maintainability, and Availability Analysis of Highwall Mining Machines in Open Pit Mines: A Comprehensive Study for Enhanced Productivity and Continuous Output
- 19 September 2025
- Published by Springer Nature in Mining, Metallurgy & Exploration
- Vol. 42 (5) , 3055-3072
Reliability, Maintainability, and Availability Analysis of Highwall Mining Machines in Open Pit Mines: A Comprehensive Study for Enhanced Productivity and Continuous Output
- Open Access
- 30 April 2025
- Published by Springer Nature in Discover Applied Sciences
- Vol. 7 (5) , 1-21
Maximizing energy savings in coal mines industrial ventilation: strategies and analysis for power reduction
- 30 April 2025
- Published by Springer Nature in Discover Applied Sciences
- Vol. 7 (5) , 1-21
Open AccessMaximizing energy savings in coal mines industrial ventilation: strategies and analysis for power reduction
- 6 October 2024
- Published by Taylor & Francis in Energy Sources, Part A: Recovery, Utilization, and Environmental Effects
- Vol. 46 (1) , 12399-12413
Highwall mining productivity enhancement with energy conservation: A case study
- 6 October 2024
- Published by Taylor & Francis in Energy Sources, Part A: Recovery, Utilization, and Environmental Effects
- Vol. 46 (1) , 12399-12413
Highwall mining productivity enhancement with energy conservation: A case study
- 8 February 2024
- Published by Springer Nature in Rock Mechanics and Rock Engineering
- Vol. 57 (5) , 3559-3575
611 Universal Drilling Machine Reliability Modeling and Performance Evaluation in Subterranean Coal Mines
- 8 February 2024
- Published by Springer Nature in Rock Mechanics and Rock Engineering
- Vol. 57 (5) , 3559-3575
611 Universal Drilling Machine Reliability Modeling and Performance Evaluation in Subterranean Coal Mines
- Open Access
Technical Risk Assessment for the Safe Design of a Man-Rider Chair Lift System
Underground mining is a difficult area for miners to work. Miners must go to the working faces by walking, which is not only time consuming but also physically demanding. In mines, a man-rider chair lift system (MRCL) has been developed to alleviate the strain stresses caused by walking lengthy and uneven distances up to the working faces. All parameters, including horizontal and vertical distances, variation and inclination of underground mines, slope forces considering the weight of persons and chair, forces acting towards return and drive unit, curves angles, power to operate, and rope safety factor, are calculated mathematically while modelling a man-rider chair lift system for both the installation and extension phases. We analyzed the analytical approach in conjunction with practical installation of the man-rider chair lift system to establish if the installation and extension of MRCL is genuinely feasible in the current scenario. We also created a simulation model of steel wire rope in Creo 8.0 for analyzing the various stresses on it with the Ansys R 16.2 software. In both phase I and phase II, the factor of safety is above that recommended, and the system is a hundred percent reliable, risk-free, and safe for operation.
Open AccessTechnical Risk Assessment for the Safe Design of a Man-Rider Chair Lift System
Underground mining is a difficult area for miners to work. Miners must go to the working faces by walking, which is not only time consuming but also physically demanding. In mines, a man-rider chair lift system (MRCL) has been developed to alleviate the strain stresses caused by walking lengthy and uneven distances up to the working faces. All parameters, including horizontal and vertical distances, variation and inclination of underground mines, slope forces considering the weight of persons and chair, forces acting towards return and drive unit, curves angles, power to operate, and rope safety factor, are calculated mathematically while modelling a man-rider chair lift system for both the installation and extension phases. We analyzed the analytical approach in conjunction with practical installation of the man-rider chair lift system to establish if the installation and extension of MRCL is genuinely feasible in the current scenario. We also created a simulation model of steel wire rope in Creo 8.0 for analyzing the various stresses on it with the Ansys R 16.2 software. In both phase I and phase II, the factor of safety is above that recommended, and the system is a hundred percent reliable, risk-free, and safe for operation.