Thong Duc Hong
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Thong Duc Hong has a total of 106 co-authors. Here are the top co-authors by number of shared publications:
Minh Quang Pham
14 shared publications- Minh Quang Pham
Faculty of Transportation Engineering, Ho Chi Minh City University of Technology (HCMUT) 1 , Dien Hong Ward, Ho Chi Minh City 700000
13 shared publications - Quan Thien Phan Nghiem
Faculty of Transportation Engineering, Ho Chi Minh City University of Technology (HCMUT), Dien Hong Ward, Ho Chi Minh City, Vietnam
6 shared publications Thang Viet Vu
4 shared publications- Wei-Cheng Wang
National Cheng Kung University
4 shared publications Ly Khanh Thi Nguyen
3 shared publications
Latest Publications
- Open Access
- 20 October 2026
- Published by Elsevier in Case Studies in Thermal Engineering
- Vol. 87
Effect of hot side structures on trade-off between thermal uniformity and performance of stationary diesel engine thermoelectric generator systems
- 20 October 2026
- Published by Elsevier in Case Studies in Thermal Engineering
- Vol. 87
Open AccessEffect of hot side structures on trade-off between thermal uniformity and performance of stationary diesel engine thermoelectric generator systems
- 1 October 2026
- Published by AIP Publishing in Physics of Fluids
- Vol. 38 (10)
Influence of baffle on fuel sloshing of partially filled fuel tanker semi-trailer: Application for enhancing rollover stability
Liquid sloshing inside partially filled tanks shifts the fluid center, affecting the rollover stability of fuel tankers during cornering. This study investigates how gasoline filling level, turning radius, and vehicle speed affect rollover stability of a tanker semi-trailer under steady-state turning. Numerical simulations based on computational fluid dynamics and the volume of fluid method are conducted to compare two tanker configurations: a non-compartmentalized tank and one equipped with internal rigid baffles. Results demonstrate that the baffles significantly dampen liquid motion; the longitudinal translation of the fluid center in the compartmentalized tank is reduced by ten times compared to the non-compartmentalized design. Furthermore, the compartmentalized design exhibits superior damping, reaching a steady state of rollover moment significantly faster than the smooth tank, thereby preventing prolonged oscillations that threaten vehicle stability. The baffles increase the rollover lateral acceleration threshold by 31.1% at 50% filling level. The compartmentalized tank maintains rollover stability at higher filling ratios, with acceleration thresholds of 0.223g and 0.236g at 70% and 90% filling levels, respectively, and allows for stable cornering at velocities up to 4.5 m/s. These findings confirm that rigid baffles effectively enhance rollover safety, providing a quantitative basis for evaluating the stability limits of liquid-carrying vehicles.
- 1 October 2026
- Published by AIP Publishing in Physics of Fluids
- Vol. 38 (10)
Influence of baffle on fuel sloshing of partially filled fuel tanker semi-trailer: Application for enhancing rollover stability
Liquid sloshing inside partially filled tanks shifts the fluid center, affecting the rollover stability of fuel tankers during cornering. This study investigates how gasoline filling level, turning radius, and vehicle speed affect rollover stability of a tanker semi-trailer under steady-state turning. Numerical simulations based on computational fluid dynamics and the volume of fluid method are conducted to compare two tanker configurations: a non-compartmentalized tank and one equipped with internal rigid baffles. Results demonstrate that the baffles significantly dampen liquid motion; the longitudinal translation of the fluid center in the compartmentalized tank is reduced by ten times compared to the non-compartmentalized design. Furthermore, the compartmentalized design exhibits superior damping, reaching a steady state of rollover moment significantly faster than the smooth tank, thereby preventing prolonged oscillations that threaten vehicle stability. The baffles increase the rollover lateral acceleration threshold by 31.1% at 50% filling level. The compartmentalized tank maintains rollover stability at higher filling ratios, with acceleration thresholds of 0.223g and 0.236g at 70% and 90% filling levels, respectively, and allows for stable cornering at velocities up to 4.5 m/s. These findings confirm that rigid baffles effectively enhance rollover safety, providing a quantitative basis for evaluating the stability limits of liquid-carrying vehicles.
- Open Access
- 23 September 2026
- Published by Elsevier in Case Studies in Thermal Engineering
- Vol. 87
Evaluating the effectiveness of multi-layer fin structure on the performance and temperature uniformity of a thermoelectric generator system on a stationary diesel engine
- 23 September 2026
- Published by Elsevier in Case Studies in Thermal Engineering
- Vol. 87
Open AccessEvaluating the effectiveness of multi-layer fin structure on the performance and temperature uniformity of a thermoelectric generator system on a stationary diesel engine
- Open Access
- 20 September 2026
- Published by Elsevier in Next Energy
- Vol. 13
Develop optimal ignition timing models as multivariable functions for diesel-LPG blends combustion in a diesel engine
- 20 September 2026
- Published by Elsevier in Next Energy
- Vol. 13
Open AccessDevelop optimal ignition timing models as multivariable functions for diesel-LPG blends combustion in a diesel engine
- Open Access
- 22 June 2026
- Published by Public Library of Science (PLoS) in PLOS ONE
- Vol. 21 (6) , e0351949
Determine the optimal ignition timing function based on combustion duration, load and fuel blending ratio of an engine powered with diesel-methanol blends
The study employs AVL Boost software to investigate the effects of different methanol blending ratios (BR) in diesel–methanol mixtures (ranging from 0 to 50%), ignition timings (IT), and combustion durations (CD) on the power and brake specific fuel consumption (BSFC) of a single-cylinder diesel engine under various loads of 85, 70, and 50%. Throughout this study, the term IT refers to the start of combustion of diesel fuel in the combustion chamber. The simulation model is validated by comparing the power and torque simulated results and experimental data, with the discrepancy less than 5%. The optimal ITs for maximum power and minimum BSFC are identified, then predictive models are developed based on these optimal IT values as functions of BR at various engine loads and CDs. The results show that the correlations between the IT, BR, CD, and engine load are linear functions. The ITs that simultaneously deliver peak power output and the lowest BSFC are governed primarily by CD, with the BR exerting a secondary effect; whereas, engine load plays a comparatively minor role. For maximum power, the largest variations in optimal ITs are approximately 15 o CA for CD, 5 o CA for BR, and 4 o CA for load. For minimum BSFC, the corresponding maximum differences are about 15, 5, and 3 o CA for CD, BR, and engine load, respectively. Optimal IT prediction models have been established that can minimize the time and cost associated with engine experimental tests to obtain the lowest BSFC and highest engine power at various CDs, engine loads, and methanol BRs.
- 22 June 2026
- Published by Public Library of Science (PLoS) in PLOS ONE
- Vol. 21 (6) , e0351949
Open AccessDetermine the optimal ignition timing function based on combustion duration, load and fuel blending ratio of an engine powered with diesel-methanol blends
The study employs AVL Boost software to investigate the effects of different methanol blending ratios (BR) in diesel–methanol mixtures (ranging from 0 to 50%), ignition timings (IT), and combustion durations (CD) on the power and brake specific fuel consumption (BSFC) of a single-cylinder diesel engine under various loads of 85, 70, and 50%. Throughout this study, the term IT refers to the start of combustion of diesel fuel in the combustion chamber. The simulation model is validated by comparing the power and torque simulated results and experimental data, with the discrepancy less than 5%. The optimal ITs for maximum power and minimum BSFC are identified, then predictive models are developed based on these optimal IT values as functions of BR at various engine loads and CDs. The results show that the correlations between the IT, BR, CD, and engine load are linear functions. The ITs that simultaneously deliver peak power output and the lowest BSFC are governed primarily by CD, with the BR exerting a secondary effect; whereas, engine load plays a comparatively minor role. For maximum power, the largest variations in optimal ITs are approximately 15 o CA for CD, 5 o CA for BR, and 4 o CA for load. For minimum BSFC, the corresponding maximum differences are about 15, 5, and 3 o CA for CD, BR, and engine load, respectively. Optimal IT prediction models have been established that can minimize the time and cost associated with engine experimental tests to obtain the lowest BSFC and highest engine power at various CDs, engine loads, and methanol BRs.
- Open Access
- 15 May 2026
- Published by Elsevier in Results in Engineering
- Vol. 30
Effect of different lifting cylinder diameters on stability and performance of the bin lifting-flipping mechanism of a garbage truck
- 15 May 2026
- Published by Elsevier in Results in Engineering
- Vol. 30
Open AccessEffect of different lifting cylinder diameters on stability and performance of the bin lifting-flipping mechanism of a garbage truck
- Open Access
- 3 April 2026
- Published by Elsevier in International Journal of Thermofluids
- Vol. 33
A novel study on enhanced temperature uniformity in a refrigerated container by optimizing inlet duct positions and their flow rates
- 3 April 2026
- Published by Elsevier in International Journal of Thermofluids
- Vol. 33
Open AccessA novel study on enhanced temperature uniformity in a refrigerated container by optimizing inlet duct positions and their flow rates
- Open Access
- 1 January 2026
- Published by Wiley in Journal of Engineering
- Vol. 2026 (1) , 1695104
Effect of the Structural Parameters on the Weight of a Two‐Stage Reduction Gearbox Used for Electric Vehicles
This work examines the influence of key structural parameters—the first‐stage gear ratio, the gear module, and the number of teeth on the driving gears—on the total gear weight of a two‐stage reduction gearbox for electric vehicles. An analytical model relating these parameters to the gear geometry, the contact and tooth‐root strength, and the resulting mass is first established and implemented in Microsoft Excel; analysis of variance is then applied to quantify the relative contribution of each factor. The results indicate that the gear‐ratio distribution has the greatest influence, accounting for 77.41% of the variation, with lower first‐stage ratios and higher second ‐stage ratios generally reducing gear weight. The number of teeth on the second‐stage driving gear has a greater effect (18.64%) than that on the first‐stage driving gear (2.95%), and the overall gear weight reduces as the number of teeth goes up. The gear module produces a complex yet minor net effect (0.03%), increasing or decreasing the gear weight depending on whether the configuration has fewer or more teeth. The lightest (minimal) configuration—a first‐stage gear ratio of 2.259, a module of 4 mm, and 27 teeth on both the first and second‐stage driving gears—weighs 5.15 kg, which is 42.66% lighter than the heaviest (maximum) configuration—a first‐stage gear ratio of 4, a module of 4 mm, and 17 teeth on both driving gears—weighing 8.98 kg. The work provides an innovative approach to multiparameter optimization for the design of lightweight two‐stage electric‐vehicle gearboxes.
- 1 January 2026
- Published by Wiley in Journal of Engineering
- Vol. 2026 (1) , 1695104
Open AccessEffect of the Structural Parameters on the Weight of a Two‐Stage Reduction Gearbox Used for Electric Vehicles
This work examines the influence of key structural parameters—the first‐stage gear ratio, the gear module, and the number of teeth on the driving gears—on the total gear weight of a two‐stage reduction gearbox for electric vehicles. An analytical model relating these parameters to the gear geometry, the contact and tooth‐root strength, and the resulting mass is first established and implemented in Microsoft Excel; analysis of variance is then applied to quantify the relative contribution of each factor. The results indicate that the gear‐ratio distribution has the greatest influence, accounting for 77.41% of the variation, with lower first‐stage ratios and higher second ‐stage ratios generally reducing gear weight. The number of teeth on the second‐stage driving gear has a greater effect (18.64%) than that on the first‐stage driving gear (2.95%), and the overall gear weight reduces as the number of teeth goes up. The gear module produces a complex yet minor net effect (0.03%), increasing or decreasing the gear weight depending on whether the configuration has fewer or more teeth. The lightest (minimal) configuration—a first‐stage gear ratio of 2.259, a module of 4 mm, and 27 teeth on both the first and second‐stage driving gears—weighs 5.15 kg, which is 42.66% lighter than the heaviest (maximum) configuration—a first‐stage gear ratio of 4, a module of 4 mm, and 17 teeth on both driving gears—weighing 8.98 kg. The work provides an innovative approach to multiparameter optimization for the design of lightweight two‐stage electric‐vehicle gearboxes.