Amir Dayan
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Amir Dayan has a total of 16 co-authors. Here are the top co-authors by number of shared publications:
- Yi Huang
University of Liverpool
7 shared publications Alexander G. Schuchinsky
Department of Electrical Engineering and Electronics, University of Liverpool, Liverpool, U.K.
3 shared publications- Alexander G. Schuchinsky
Department of Electrical Engineering and Electronics, University of Liverpool, Liverpool, U.K.
3 shared publications Mattias Gustafsson
Huawei Technologies Sweden AB, Gothenburg, Sweden
3 shared publications- Farhad Ghorbani
Department of Electrical Engineering and Electronics, University of Liverpool, Liverpool, U.K.
2 shared publications - Jiafeng Zhou
University of Liverpool
2 shared publications
Latest Publications
- Open Access
Highly Linear Loaded-Line Phase Shifter Utilizing Impedance Transformer and PIN Diode
This paper presents a highly linear one-bit loaded-line phase shifter that leverages PIN diodes in combination with a coupler-based impedance transformer. The proposed phase shifter adopts a loaded-line topology, where PIN diodes are configured in a parallel-to-ground arrangement to improve linearity performance. To further enhance linearity, a coupler-based impedance transformer is employed to reduce the impedance seen by each PIN diode, thereby minimizing nonlinear behavior. To demonstrate the effectiveness of this design, a one-bit digital phase shifter is developed, simulated, and fabricated to achieve a 45-degree phase shift at 2 GHz. Experimental measurements confirm an input third-order intercept point (IIP3) exceeding 100 dBm under a range of test conditions, validating the proposed architecture’s linearity advantages.
Open AccessHighly Linear Loaded-Line Phase Shifter Utilizing Impedance Transformer and PIN Diode
This paper presents a highly linear one-bit loaded-line phase shifter that leverages PIN diodes in combination with a coupler-based impedance transformer. The proposed phase shifter adopts a loaded-line topology, where PIN diodes are configured in a parallel-to-ground arrangement to improve linearity performance. To further enhance linearity, a coupler-based impedance transformer is employed to reduce the impedance seen by each PIN diode, thereby minimizing nonlinear behavior. To demonstrate the effectiveness of this design, a one-bit digital phase shifter is developed, simulated, and fabricated to achieve a 45-degree phase shift at 2 GHz. Experimental measurements confirm an input third-order intercept point (IIP3) exceeding 100 dBm under a range of test conditions, validating the proposed architecture’s linearity advantages.
- 8 November 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 73 (5) , 2523-2530
Phase Effects on Combined Passive Intermodulation From Multiple Sources
Signal distortion caused by passive intermodulation (PIM) poses a significant challenge to modern multicarrier communications and radar systems. This article is concerned with modeling the superposition of reverse PIM products generated by weak nonlinear sources and proposes means of PIM mitigation accordingly. The developed model is experimentally validated using an open-ended coaxial waveguide with a movable iron insert serving as the main PIM source. The study explores PIM interactions from multiple sources and introduces a new circuit comprising three negatively biased p-i-n diodes separated by 60 $^{\circ}$ transmission lines. It substantially reduces reverse PIM by over 30 dB with a minimal footprint compared to previous studies. The potential of this circuit for measuring the reverse PIM phase is explored theoretically and experimentally for the first time, showing trends in agreement with a mean absolute error of 19.49 $^{\circ}$ .
- 8 November 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 73 (5) , 2523-2530
Phase Effects on Combined Passive Intermodulation From Multiple Sources
Signal distortion caused by passive intermodulation (PIM) poses a significant challenge to modern multicarrier communications and radar systems. This article is concerned with modeling the superposition of reverse PIM products generated by weak nonlinear sources and proposes means of PIM mitigation accordingly. The developed model is experimentally validated using an open-ended coaxial waveguide with a movable iron insert serving as the main PIM source. The study explores PIM interactions from multiple sources and introduces a new circuit comprising three negatively biased p-i-n diodes separated by 60 $^{\circ}$ transmission lines. It substantially reduces reverse PIM by over 30 dB with a minimal footprint compared to previous studies. The potential of this circuit for measuring the reverse PIM phase is explored theoretically and experimentally for the first time, showing trends in agreement with a mean absolute error of 19.49 $^{\circ}$ .
- 23 August 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 73 (2) , 789-800
Linearity Enhancement in PIN-Diode-Based Switches
In telecommunication systems, like full-duplex transceivers, simultaneous transmission, and reception demand highly linear components to minimize intermodulation interference. PIN-diode-based RF switches used either independently or as part of a device, can introduce nonlinearity in both on and off states. This article evaluates the impact of the topology on the linearity of PIN-diode-based RF switches and proposes an optimal two-diode arrangement to achieve superior linearity performance. The proposed topology combines the strengths of the series and parallel topologies while mitigating their weaknesses. Owing to its inclusion of two PIN diodes, the proposed topology also leverages the distance between them to further increase the linearity. The presented analysis indicates that having a quarter-wavelength distance between the diodes is key for achieving intermodulation cancellation in the on state, resulting in a 12 dB IIP3 enhancement. In the off state, complete distortion cancellation is more complicated due to additional reflections. The quarter wavelength transmission line was utilized as an impedance transformer to improve linearity by altering the impedance seen by each diode. Detailed analysis, supported by mathematical and experimental results, confirms a 20 dB improvement in IIP3 in the off state. Consequently, the peak IIP3 values, 99 dBm in the on state, and 111 dBm in the off state occur within a narrow bandwidth. The proposed switch maintains an IIP3 of 95 dBm in both states across a wider bandwidth of 1.8–2.6 GHz.
- 23 August 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 73 (2) , 789-800
Linearity Enhancement in PIN-Diode-Based Switches
In telecommunication systems, like full-duplex transceivers, simultaneous transmission, and reception demand highly linear components to minimize intermodulation interference. PIN-diode-based RF switches used either independently or as part of a device, can introduce nonlinearity in both on and off states. This article evaluates the impact of the topology on the linearity of PIN-diode-based RF switches and proposes an optimal two-diode arrangement to achieve superior linearity performance. The proposed topology combines the strengths of the series and parallel topologies while mitigating their weaknesses. Owing to its inclusion of two PIN diodes, the proposed topology also leverages the distance between them to further increase the linearity. The presented analysis indicates that having a quarter-wavelength distance between the diodes is key for achieving intermodulation cancellation in the on state, resulting in a 12 dB IIP3 enhancement. In the off state, complete distortion cancellation is more complicated due to additional reflections. The quarter wavelength transmission line was utilized as an impedance transformer to improve linearity by altering the impedance seen by each diode. Detailed analysis, supported by mathematical and experimental results, confirms a 20 dB improvement in IIP3 in the off state. Consequently, the peak IIP3 values, 99 dBm in the on state, and 111 dBm in the off state occur within a narrow bandwidth. The proposed switch maintains an IIP3 of 95 dBm in both states across a wider bandwidth of 1.8–2.6 GHz.
- 16 February 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 72 (8) , 4892-4899
Passive Intermodulation in Metal-to-Metal Contacts Caused by Tunneling Current
Passive intermodulation (PIM) by metal contacts limits the bandwidth and capacity of radio links used in mobile and satellite communications. In this work, we investigate the effect of nonlinearities in metal-insulator-metal (MIM) contacts and their effects on PIM generation. An analytical expression is obtained for the tunneling current density which has an error of $\sim$ 1.6% in the case of a very thin insulator and low voltages in MIM junctions. The presented analytical model of the contact surfaces with the fractal geometry is used to simulate PIM products of third-order (PIM3) and fifth-order (PIM5) versus the contact resistance and applied pressure. The simulation results are validated experimentally by an open-ended rectangular coaxial structure with a slotted enclosure. The measurement results demonstrate that the presented model predicts the PIM with a mean error of about 4.8 dB when the contact pressure varies from 0.5 to 1.7 MPa.
- 16 February 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 72 (8) , 4892-4899
Passive Intermodulation in Metal-to-Metal Contacts Caused by Tunneling Current
Passive intermodulation (PIM) by metal contacts limits the bandwidth and capacity of radio links used in mobile and satellite communications. In this work, we investigate the effect of nonlinearities in metal-insulator-metal (MIM) contacts and their effects on PIM generation. An analytical expression is obtained for the tunneling current density which has an error of $\sim$ 1.6% in the case of a very thin insulator and low voltages in MIM junctions. The presented analytical model of the contact surfaces with the fractal geometry is used to simulate PIM products of third-order (PIM3) and fifth-order (PIM5) versus the contact resistance and applied pressure. The simulation results are validated experimentally by an open-ended rectangular coaxial structure with a slotted enclosure. The measurement results demonstrate that the presented model predicts the PIM with a mean error of about 4.8 dB when the contact pressure varies from 0.5 to 1.7 MPa.
- Open Access
- 22 November 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in TechRxiv
Passive Intermodulation in Metal-to-Metal Contacts Caused by Tunneling Current
Passive intermodulation (PIM) by metal contacts limits the bandwidth and capacity of radio links used in mobile and satellite communications. In this work, we investigate the effect of nonlinearities of metal-to-metal contacts and their effects on PIM generation. An analytical expression is obtained for the tunneling current density which has an error of ~1.6% in the case of a very thin insulator and low voltages in MIM (Metal-InsulatorMetal) junctions. The presented analytical model of the contact surfaces with the fractal geometry is applied to simulate PIM products of third-order (PIM3) and fifth-order (PIM5) versus the contact resistance and applied pressure. The simulation results are validated experimentally by an open-ended rectangular coaxial structure with a slotted enclosure. The measurement results demonstrate that the presented model predicts the PIM with a mean error of about 4.8 dB when the contact pressure varies from 0.5 MPa to 1.7 MPa.
- 22 November 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in TechRxiv
Open AccessPassive Intermodulation in Metal-to-Metal Contacts Caused by Tunneling Current
Passive intermodulation (PIM) by metal contacts limits the bandwidth and capacity of radio links used in mobile and satellite communications. In this work, we investigate the effect of nonlinearities of metal-to-metal contacts and their effects on PIM generation. An analytical expression is obtained for the tunneling current density which has an error of ~1.6% in the case of a very thin insulator and low voltages in MIM (Metal-InsulatorMetal) junctions. The presented analytical model of the contact surfaces with the fractal geometry is applied to simulate PIM products of third-order (PIM3) and fifth-order (PIM5) versus the contact resistance and applied pressure. The simulation results are validated experimentally by an open-ended rectangular coaxial structure with a slotted enclosure. The measurement results demonstrate that the presented model predicts the PIM with a mean error of about 4.8 dB when the contact pressure varies from 0.5 MPa to 1.7 MPa.
- Open Access
- 22 November 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in TechRxiv
Mitigation of Passive Intermodulation Generated by Discrete Nonlinear Sources
Nonlinear signal distortion, caused by passive intermodulation (PIM), presents a major challenge to modern multi-carrier communications and radar systems. Reverse PIM products generated by discrete nonlinear sources are analyzed in this paper, and the means of PIM mitigation are proposed. The developed model is validated experimentally using an open-ended coaxial waveguide with a movable iron insert, which acts as a main PIM source. The PIM generation mechanisms revealed in this study have identified alternative means for PIM mitigation. A novel circuit, proposed in the paper, enables an effective reduction ofthe reverse PIM for more than 44 dB.
- 22 November 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in TechRxiv
Open AccessMitigation of Passive Intermodulation Generated by Discrete Nonlinear Sources
Nonlinear signal distortion, caused by passive intermodulation (PIM), presents a major challenge to modern multi-carrier communications and radar systems. Reverse PIM products generated by discrete nonlinear sources are analyzed in this paper, and the means of PIM mitigation are proposed. The developed model is validated experimentally using an open-ended coaxial waveguide with a movable iron insert, which acts as a main PIM source. The PIM generation mechanisms revealed in this study have identified alternative means for PIM mitigation. A novel circuit, proposed in the paper, enables an effective reduction ofthe reverse PIM for more than 44 dB.
- 26 March 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-4
Contact Nonlinearities of Rough Conductors in Antennas and Connectors
Contacts of conductors with rough surfaces cause losses and nonlinear distortion of the high-power signals at high frequencies. The contact nonlinearities are analysed in a pair and array of the contact asperities in metal-insulator-metal (MIM) junctions. An improved model of the tunnelling resistivity is proposed and its accuracy is demonstrated for the harmonic signals. The model is also applied to the analysis of the thermal effect on the contact resistivity of rough conductors.
- 26 March 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-4
Contact Nonlinearities of Rough Conductors in Antennas and Connectors
Contacts of conductors with rough surfaces cause losses and nonlinear distortion of the high-power signals at high frequencies. The contact nonlinearities are analysed in a pair and array of the contact asperities in metal-insulator-metal (MIM) junctions. An improved model of the tunnelling resistivity is proposed and its accuracy is demonstrated for the harmonic signals. The model is also applied to the analysis of the thermal effect on the contact resistivity of rough conductors.
- Open Access
- 3 February 2022
- Published by MDPI AG in Electronic Materials
- Vol. 3 (1) , 65-81
Passive Intermodulation at Contacts of Rough Conductors
Passive intermodulation (PIM) is a niggling phenomenon that debilitates the performance of modern communications and navigation systems. PIM products interfere with information signals and cause their nonlinear distortion. The sources and basic mechanisms of PIM have been studied in the literature but PIM remains a serious problem of signal integrity. In this paper, the main sources and mechanisms of PIM generation by joints of good conductors are discussed. It is shown that the passive electrical, thermal and mechanical nonlinearities are intrinsically linked despite their distinctively different time scales. The roughness of the contact surfaces plays an important role in PIM generation by conductor joints. A review of the PIM phenomenology at the contacts of the good conductors suggests that novel multiphysics models are necessary for the analysis and reliable prediction of PIM products generated by several concurrent nonlinearities of a diverse physical nature.
- 3 February 2022
- Published by MDPI AG in Electronic Materials
- Vol. 3 (1) , 65-81
Open AccessPassive Intermodulation at Contacts of Rough Conductors
Passive intermodulation (PIM) is a niggling phenomenon that debilitates the performance of modern communications and navigation systems. PIM products interfere with information signals and cause their nonlinear distortion. The sources and basic mechanisms of PIM have been studied in the literature but PIM remains a serious problem of signal integrity. In this paper, the main sources and mechanisms of PIM generation by joints of good conductors are discussed. It is shown that the passive electrical, thermal and mechanical nonlinearities are intrinsically linked despite their distinctively different time scales. The roughness of the contact surfaces plays an important role in PIM generation by conductor joints. A review of the PIM phenomenology at the contacts of the good conductors suggests that novel multiphysics models are necessary for the analysis and reliable prediction of PIM products generated by several concurrent nonlinearities of a diverse physical nature.
- 17 April 2002
- Published by Elsevier in International Journal of Heat and Mass Transfer
- Vol. 45 (19) , 4021-4031
Laminar free convection underneath a hot horizontal infinite flat strip
- 17 April 2002
- Published by Elsevier in International Journal of Heat and Mass Transfer
- Vol. 45 (19) , 4021-4031
Laminar free convection underneath a hot horizontal infinite flat strip