TLThorsten Lill

Thorsten Lill

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Thorsten Lill has a total of 81 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Polyurea films deposited by molecular layer deposition for surface and sidewall passivation during HF plasma etching of high-aspect-ratio structures

    by Wallis E. Scholl, Xue Wang, Andrew P. Kaye, Mingmei Wang, Wenyu Zhang, Thorsten Lill, Harmeet Singh, Sumit Agarwal

    Molecular layer deposition (MLD) was used to deposit polyurea films using toluene diisocyanate and ethylenediamine as precursors. Polyurea was deposited on SiO2 and SiNx blanket films and exposed to an HF plasma to evaluate plasma-surface interactions. The surface composition was monitored using in situ infrared spectroscopy. During the initial stages of HF plasma exposure, polyurea was sacrificially etched, while etching of the underlying SiO2 or SiNx films was negligible. Once polyurea was completely consumed by reactions with plasma species, the underlying SiO2 or SiNx films were etched at their baseline etch rates. Despite the high porosity of the MLD films, the presence of polyurea prevented etching of the underlying material, showing that polyurea efficiently consumed the reactive plasma species. Fluorination of polyurea was observed prior to its removal, suggesting that polyurea was removed as hydrofluorocarbons during HF plasma etching. Finally, polyurea was deposited on ∼65:1 aspect-ratio holes in SiO2-SiNx stacks and then exposed to an etching plasma to evaluate the sidewall passivation. We show that polyurea was deposited throughout the entire hole using the saturation doses for a flat surface, although the thickness on the sidewalls was lower than the planar surface. After MLD, in the second etch step, the polyurea film preserved the critical dimension throughout the high-aspect-ratio feature.

  • Detection of silicon-containing etch products during SiN x etching in a hydrogen fluoride plasma using quadrupole mass spectrometry

    by Xue Wang, Md Tanzid Hossain, Prabhat Kumar, Thorsten Lill, Mingmei Wang, Taner Ozel, Harmeet Singh, Sumit Agarwal

    We have designed and fabricated a two-stage differentially pumped setup for a quadrupole mass spectrometer to identify stable etch products generated during etching of SiNx in an HF plasma under an applied bias voltage of −240 V to the substrate. In this setup, the etch products can be directly collected into a sampling cone with a 1 mm aperture at a distance of ∼3 mm from the sample surface, which is shorter than the mean free path in the HF plasma at 10 mTorr. We show that SiF4 is the primary Si-containing etch product. It is unlikely that SiF2 is an etch product during SiNx etching at the conditions employed in this study. We also detected small fractions of SiH2F2 and SiHF3 released from the SiNx surface during etching. Since the electron impact ionization cross sections for SiH2F2 and SiHF3 are not available in the literature, we could not estimate their relative abundance compared to SiF4. We were unable to conclusively detect NH3 as the primary N-containing etch product due to background H2O in the chamber, which has a cracking pattern that overlaps with NH3 at mass-to-charge ratios of 16 and 17.

  • Effect of gas additives on reaction barriers in cryo etching of silicon oxide and nitride

    by Yichen Fan, Thorsten Lill, Mingmei Wang, Dongjun Wu, Gopal Iyer, Yuri Barsukov, Weitao Yang, Harmeet Singh

    Vertical scaling of 3D NAND devices calls for higher SiO2 and SiN etching rates and meaningful reduction of aspect ratio dependent etching. Recently, evolutionary improvements of the fluorocarbon gas process have been replaced by novel so-called cryo etching processes using HF as the main etch gas. In this paper, we report computational results for the activation Gibbs free energies ΔG‡ for the reaction of HF and various additive gases with SiO2 and SiN. The results are compared with available experimental trends. We find that the dipole moment of the additive gas is an indicator of its catalytic effect.


  • Temperature dependence of the growth per cycle during molecular layer deposition of polyurea on plasma deposited SiO2

    by Wallis E. Scholl, Mingmei Wang, Thorsten Lill, Harmeet Singh, Sumit Agarwal

    In molecular layer deposition (MLD), the growth per cycle (GPC) depends on process conditions with no well-defined temperature window. During MLD of polyurea using toluene diisocyanate (TDIC) and ethylendiamine (ED) as MLD precursors, the GPC decreased with deposition temperature from 0.22 nm at 0 °C to 0.022 nm at 45 °C. While we observed the reaction of toluene diisocyanate with the underlying SiO2 at 45 °C, at 22 °C, in situ infrared spectroscopy indicates that the MLD film is not anchored to the substrate via covalent bonds. TDIC and ED displayed different temperature-dependent interactions with the growing polyurea film during MLD. Specifically, at lower temperatures, ED was more likely to be added to the film via physisorption, and as a consequence, TDIC was more likely to double react with both its functional groups to –NH2 sites within the film. While the lower GPC at higher temperature is driven predominantly by a decrease in ED physisorption, the rate of TDIC double reaction must also decrease due to the lower density of available reactive sites. As a result, at higher temperatures, both ED physisorption and TDIC double reactions are suppressed, and the ratio of polyurea linkages formed in each half-cycle was closer to unity. While the GPC was the highest at 0 °C, we also show that the films deposited at a lower temperature were unstable in both vacuum and the ambient and showed up to ∼15% decrease in thickness, most likely due to the desorption of physisorbed precursor molecules.


  • Formation and stability of ammonium fluorosilicate during etching of SiN x in CH2F2/Ar and SF6/H2 plasmas

    by Xue Wang, Tanzid Hossain, Prabhat Kumar, Thorsten Lill, Mingmei Wang, Taner Ozel, Harmeet Singh, Sumit Agarwal

    During reactive ion etching of SiNx in fluorine-based plasmas where HF is produced through a combination of gas-phase and surface reactions, ammonium fluorosilicate (AFS) has been reported to form on the SiNx surface. However, the underlying mechanism for AFS formation and its role in SiNx etching is still unclear, particularly during etching under energetic ion bombardment. In this work, using in situ attenuated total reflection Fourier-transform infrared spectroscopy, we show that during SiNx etching with a CH2F2/Ar plasma, when the substrate was at room temperature at a bias voltage of −240 V, an etch stop occurred with the simultaneous accumulation of graphitic hydrofluorocarbon and AFS on the SiNx surface. Under nominally similar conditions in a CH2F2/Ar plasma, but with the substrate at 70 or 120 °C, no etch stop was observed along with the absence of hydrofluorocarbon and AFS. By eliminating the formation of a graphitic hydrofluorocarbon layer in a SF6/H2 plasma, also at a bias voltage of −240 V, we reveal that AFS accumulation does not necessarily lead to an etch stop, and a steady-state thickness of AFS appears on surface as a result of a balance between AFS formation due to SiNx etching and AFS decomposition due to the impingement of energetic ions and H radicals. The effect of the substrate bias voltage on the etch behavior and surface composition was also studied in CH2F2/Ar and SF6/H2 plasmas. Our results show that the AFS is likely mixed with the underlying SiNx film under energetic ion bombardment instead of being present as a well-defined uniform layer. As a result, the presence of AFS does not necessarily lead to an etch stop. AFS formed on the SiNx surface decomposed when exposed to H radicals generated in H2 plasma under self-bias. Therefore, we conclude that the H radicals can play a dual role where they facilitate AFS formation by scavenging F radicals to form HF, but can also directly remove AFS formed on the surface. Finally, the slow removal of AFS by increasing the temperature to 70 °C suggests that AFS accumulation can be controlled with the substrate temperature.


  • ALD and ALE Applications in 3D Monolithic Device Integration

    by Thorsten Lill, Andreas Fischer, Fred Roozeboom

    Two-dimensional scaling of integrated circuits has been the backbone of Moore’s Law until recently. As feature sizes reach physical limits, new approaches are needed. Monolithic scaling in the third dimension is one of the solutions. NAND flash memory started to grow in the vertical direction in 2014 with just 24 layers of memory cells with 128Gbit storage. The fact that the industry is targeting 1000 layers only 10 years later is testament to the stunning success of vertical integration. Logic and dynamic random-access memories (DRAM) are also conquering the third dimension. The structures of these devices are very complicated and novel lateral integration involving conformal deposition and isotropic etching are key enablers. In this talk we will discuss examples of combined use of ALD and ALE to realize thin smooth and crystalline films, selective deposition and lateral stacked films. The etching can be performed using radical etch, thermal etch and thermal ALE depending on the process requirements.

  • New Developments in High Aspect Ratio Etching of 3D Memory Devices

    by Thorsten Lill, Mingmei Wang, Youn-Jin Oh, Harmeet Singh

    Advanced electronic devices are integrated in the vertical direction, and critical challenges in etching deep structures with high aspect ratios must be addressed to advance the technology roadmap. Among the enabling applications, vertical etching of SiO 2 and SiN for flash memory devices features prominently. Recently, HF is used in high aspect ratio plasma etching of SiO 2 , SiN and multilayer stacks of these films at wafer temperatures below room temperature. The etching mechanisms for these so called cryo etch processes are very different from traditional dielectric etching. Instead of reactive fluorocarbon polymers which react with SiO 2 and SiN under ion bombardment, the process forms ammonium fluorosilicate (NH 4 ) 2 SiF 6 or AFS as an intermediate reaction product. In this paper, we will present experimental results on plasma and vapor etching of SiO 2 and SiN. The underlaying etching mechanisms will be explained using molecular dynamics and density functional theory. The new cryo etching process is fast evolving to meet profile requirements for future nodes and achieves higher etch rates. This is enabled by chemistry and RF technology innovation.

  • Growth Mechanism During Initial Stages of Molecular Layer Deposition of Polyurea

    by Wallis E. Scholl, Mingmei Wang, Thorsten Lill, Rachel A. Nye de Castro, Eric A. Hudson, Sumit Agarwal

    Molecular layer deposition (MLD) is of interest as a technique for growing ultrathin polymeric films for various applications. However, the basic surface adsorption and reaction process are still not well understood, leading to challenges in achieving high growth rates and good reproducibility. This study uses in situ Fourier-transform infrared spectroscopy in combination with in situ ellipsometry to better understand the initial stages of MLD of polyurea. 1,4 diisocyanatobutane (DICB) and diethylene triamine (DETA) were used as MLD precursors, and polyurea was grown through the reaction between an isocyanate group supplied by DICB and an amine group supplied by DETA. The growth per cycle was fit from ellipsometry measurements to be 0.022 nm/cycle. Film growth was also confirmed by infrared spectroscopy, which showed isocyanate groups being alternately added and consumed during the DICB and DETA half-cycles. Amide I/II modes increased in absorbance with every half-cycle as polyurea linkages were formed between incoming molecules and the growing film. We show that although some surface reactive sites are terminated during film deposition, new sites are introduced by precursor physisorption. Furthermore, we show that different precursors have different rates of double reaction and physisorption, highlighting the complex interactions between the molecular precursors and the growing film. DICB has a high rate of double reactions and a low rate of physisorption, as evidenced by the loss of isocyanate sites throughout initial stages of growth. To maintain linear film growth, DETA physisorbs into the film, thereby adding new amine sites for incoming molecules to react with. These results provide useful insight into mechanisms that control the MLD of thin films.


  • (Invited) Recent Progress in High Aspect Ratio Etching of 3D Memory Devices

    by Thorsten Lill, Mingmei Wang, Qing Xu, Youn-Jin Oh, Harmeet Singh

    Advanced electronic devices are integrated in the vertical direction, and critical challenges in etching deep structures with high aspect ratios must be addressed to advance the technology roadmap. Among the enabling applications, vertical etching of SiO2 and SiN for flash memory devices features prominently. Recently, HF is used in high aspect ratio plasma etching of SiO2, SiN and multilayer stacks of these films at wafer temperatures below room temperature. The etching mechanisms for these so called cryo etch processes are very different from traditional dielectric etching. Instead of reactive fluorocarbon polymers which react with SiO2 and SiN under ion bombardment, the process forms ammonium fluorosilicate (NH4)2SiF6 or AFS as an intermediate reaction product. In this paper, we will present experimental results on plasma and vapor etching of SiO2 and SiN. Included in this study are experimental processing regimes characterized by varied ion flux and energy levels with varying degrees of RF power. The underlaying etching mechanisms will be explained using molecular dynamics and density functional theory. The new cryo etching process is fast evolving to meet profile requirements for future nodes and achieves higher etch rates. This is enabled by chemistry and RF technology innovation.

  • Open Access

    Plasma sources for advanced semiconductor applications

    by Oscar Versolato, Igor Kaganovich, Kallol Bera, Thorsten Lill, Hyo-Chang Lee, Ronnie Hoekstra, John Sheil, Sang Ki Nam

    Semiconductors are the foundation of modern technology, used in our personal, industrial, and military-grade devices. Every aspect of U.S. society is closely ti Semiconductors are the foundation of modern technology, used in our personal, industrial, and military-grade devices. Every aspect of U.S. society is closely ti