Viktor Alekseevich Kukartsev
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Viktor Alekseevich Kukartsev has a total of 47 co-authors. Here are the top co-authors by number of shared publications:
- Vadim Sergeevich Tynchenko
Bauman Moscow State Technical University, Moscow, Russian Federation
14 shared publications - Nikita Vladimirovich Martyushev
Department of Information Technology, Tomsk Polytechnic University, 634050 Tomsk, Russia
12 shared publications - Vladislav Viktorovich Kukartsev
Department of Software Engineering, Siberian Federal University, Krasnoyarsk 660041, Russia
12 shared publications - Boris V. Malozyomov
Department of Electrotechnical Complexes, Novosibirsk State Technical University, 20, Karla Marksa Ave., 630073 Novosibirsk, Russia
9 shared publications - Yadviga Aleksandrovna Tynchenko
Department of Technological Machines and Equipment for the Oil and Gas Complex, Siberian Federal University, Krasnoyarsk 660041, Russia
7 shared publications - Kirill Aleksandrovich Bashmur
Department of Technological Machines and Equipment of Oil and Gas Complex, Siberian Federal University, 660041 Krasnoyarsk, Russia
5 shared publications
Latest Publications
- Open Access
Field-Validated Probabilistic Digital Twin of a Shipboard Microgrid for Reliability-Oriented Operation: Applications to Hybrid and Unmanned Vessels
The transition toward unmanned and hybrid vessels increases the requirements for diagnosability and continuity of power supply to critical consumers under physical and information-layer faults. The aim of this study is to develop a probabilistic digital twin of a shipboard microgrid that combines nonlinear state estimation, Bayesian mode inference, adaptive measurement-quality accounting, and risk-aware power reconfiguration. Field validation was performed using a long-term operational measurement program. The database comprises 12 classes of operating and fault events, with 30 field records per class, yielding 360 thirty-minute records, 180 h of observations, and 162,360 time samples at a 4 s sampling interval. Three diagnostic and control methods were applied to the same field records, producing 1080 paired algorithmic evaluations. Relative to the deterministic digital twin, the proposed method reduced voltage RMSE by 37.3%, SOC RMSE by 32.7%, and power RMSE by 30.1%, while reducing ENS by 13.3%. Mean fault-detection delay did not differ significantly from that of the deterministic approach; however, the missed-detection rate decreased from 12.7% to 7.3%. Compared with threshold-based protection, detection latency and recovery time were reduced by 25.7% and 30.8%, respectively. The field evidence therefore supports the proposed architecture as a supervisory state-estimation, diagnosis, and energy-reconfiguration layer. Because the field records originate from one operator and predominantly conventional tanker vessels, transfer to hybrid and unmanned platforms requires prospective onboard validation on the target vessel classes.
Open AccessField-Validated Probabilistic Digital Twin of a Shipboard Microgrid for Reliability-Oriented Operation: Applications to Hybrid and Unmanned Vessels
The transition toward unmanned and hybrid vessels increases the requirements for diagnosability and continuity of power supply to critical consumers under physical and information-layer faults. The aim of this study is to develop a probabilistic digital twin of a shipboard microgrid that combines nonlinear state estimation, Bayesian mode inference, adaptive measurement-quality accounting, and risk-aware power reconfiguration. Field validation was performed using a long-term operational measurement program. The database comprises 12 classes of operating and fault events, with 30 field records per class, yielding 360 thirty-minute records, 180 h of observations, and 162,360 time samples at a 4 s sampling interval. Three diagnostic and control methods were applied to the same field records, producing 1080 paired algorithmic evaluations. Relative to the deterministic digital twin, the proposed method reduced voltage RMSE by 37.3%, SOC RMSE by 32.7%, and power RMSE by 30.1%, while reducing ENS by 13.3%. Mean fault-detection delay did not differ significantly from that of the deterministic approach; however, the missed-detection rate decreased from 12.7% to 7.3%. Compared with threshold-based protection, detection latency and recovery time were reduced by 25.7% and 30.8%, respectively. The field evidence therefore supports the proposed architecture as a supervisory state-estimation, diagnosis, and energy-reconfiguration layer. Because the field records originate from one operator and predominantly conventional tanker vessels, transfer to hybrid and unmanned platforms requires prospective onboard validation on the target vessel classes.
- 30 June 2024
- Published by Ore and Metals Publishing House in CIS Iron and Steel Review
- Vol. 27, 84-90
Investigation of properties of laminar antiferromagnetic nanostructures
When creating products using magnetoresistive materials based on magnetic and non-magnetic metals, one is focused on achieving giant magnetoresistance. Such an effect, obtained at the turn of 1980–90-ies years of the last century in superlattices, reached 10–80 % with the intensity of tens of kE at 4.5 K. By methods of physics of magnetic phenomena the regularities of interaction between ferromagnetics and antiferromagnetics, constituting alloys, are determined for strengthening the design of spin valves. Insights into the formation of anisotropy in manganese and permalloy bilayers are detailed. Differences of layer creation causally related to the thermomagnetic activation mode of the process have been determined. The use of alloys in antiferromagnetic nanostructures can indeed lead to the formation of unidirectional anisotropy with changing values of the exchange shift of the hysteresis loop. It has been shown that nanostructures containing alloys exhibit improved magnetism and exchange interaction properties. These results confirm the potential of alloys in creating materials with improved magnetic phenomena and possible applications in various fields such as electronics and magnetic devices.
- 30 June 2024
- Published by Ore and Metals Publishing House in CIS Iron and Steel Review
- Vol. 27, 84-90
Investigation of properties of laminar antiferromagnetic nanostructures
When creating products using magnetoresistive materials based on magnetic and non-magnetic metals, one is focused on achieving giant magnetoresistance. Such an effect, obtained at the turn of 1980–90-ies years of the last century in superlattices, reached 10–80 % with the intensity of tens of kE at 4.5 K. By methods of physics of magnetic phenomena the regularities of interaction between ferromagnetics and antiferromagnetics, constituting alloys, are determined for strengthening the design of spin valves. Insights into the formation of anisotropy in manganese and permalloy bilayers are detailed. Differences of layer creation causally related to the thermomagnetic activation mode of the process have been determined. The use of alloys in antiferromagnetic nanostructures can indeed lead to the formation of unidirectional anisotropy with changing values of the exchange shift of the hysteresis loop. It has been shown that nanostructures containing alloys exhibit improved magnetism and exchange interaction properties. These results confirm the potential of alloys in creating materials with improved magnetic phenomena and possible applications in various fields such as electronics and magnetic devices.
- Open Access
Increasing the Efficiency of Diagnostics in the Brush-Commutator Assembly of a Direct Current Electric Motor
Increasing the productivity and reliability of mining infrastructure facilities is an important task in achieving future goals. Mining dump trucks are an important part of coal mine infrastructure. In this article, to determine the reliability indicators in a brush–commutator unit and the residual life of electric motor brushes, a mathematical model for processing statistical data has been developed, which allows for the classification of types of failures and, unlike existing models, the determination of the life of the brushes according to the maximum extent of their wear. A method for predicting the residual life of an electric brush in a DC electric motor is presented, which contains a list of controlled reliability indicators, included a mathematical model. The described model improves the accuracy of the prediction and detection of DC motor failures. The derivation of the general formula for calculating the residual life of electric brushes is given. Based on the proposed mathematical model, we studied and calculated the reliability of the brush–commutator unit, the minimum height of the brush during operation, the average rate of its wear, the standard deviation and the mathematical expectation of brush wear. A nomogram of the failure-free operation time of the brush–commutator unit in a DC electric motor was modeled using the height of the brush during operation. Output parameters after the implementation of this monitoring system include the reliability of the electric motor operation. At the same time, diagnostic characteristics are improved twofold, and the residual life of the brush-switching unit is increased by 28–30%.
Open AccessIncreasing the Efficiency of Diagnostics in the Brush-Commutator Assembly of a Direct Current Electric Motor
Increasing the productivity and reliability of mining infrastructure facilities is an important task in achieving future goals. Mining dump trucks are an important part of coal mine infrastructure. In this article, to determine the reliability indicators in a brush–commutator unit and the residual life of electric motor brushes, a mathematical model for processing statistical data has been developed, which allows for the classification of types of failures and, unlike existing models, the determination of the life of the brushes according to the maximum extent of their wear. A method for predicting the residual life of an electric brush in a DC electric motor is presented, which contains a list of controlled reliability indicators, included a mathematical model. The described model improves the accuracy of the prediction and detection of DC motor failures. The derivation of the general formula for calculating the residual life of electric brushes is given. Based on the proposed mathematical model, we studied and calculated the reliability of the brush–commutator unit, the minimum height of the brush during operation, the average rate of its wear, the standard deviation and the mathematical expectation of brush wear. A nomogram of the failure-free operation time of the brush–commutator unit in a DC electric motor was modeled using the height of the brush during operation. Output parameters after the implementation of this monitoring system include the reliability of the electric motor operation. At the same time, diagnostic characteristics are improved twofold, and the residual life of the brush-switching unit is increased by 28–30%.
- Open Access
A Methodological Approach to the Simulation of a Ship’s Electric Power System
Modern ships are complex energy systems containing a large number of different elements. Each of these elements is simulated separately. Since all these models form a single system (ship), they are interdependent. The operating modes of some systems influence others, but at the same time, the work of all the systems should be aimed at fulfilling the basic functions of the ship. The work proposes a methodological approach to combining various systems of ships into a single complex model. This model allows combining models of ship systems of various levels (microlevel, macrolevel, metalevel, megalevel). The work provides examples of models of such multi-level energy systems. These are energy systems composed of an electric generator, a diesel engine, a propeller shaft, and algorithms used for operating the common parts of the ship’s electric power system and a piston wear process. Analytical, structural, numerical, and object-oriented models were made for these objects. Each of these particular models describes a limited class of problems, has characteristic properties, and a mathematical structure. The work shows how particular models can be interconnected using a set-theoretic description. Particular models are combined into macrolevel models, whose output parameters are quantities that are by no means related. The macrolevel models are interrelated using control models. Control models belong to the metalevel and allow for assigning settings and response thresholds to algorithms used in automation systems. Such a model (megalevel model) allows, ultimately, investigating the dynamics of the entire system as a whole and managing it.
Open AccessA Methodological Approach to the Simulation of a Ship’s Electric Power System
Modern ships are complex energy systems containing a large number of different elements. Each of these elements is simulated separately. Since all these models form a single system (ship), they are interdependent. The operating modes of some systems influence others, but at the same time, the work of all the systems should be aimed at fulfilling the basic functions of the ship. The work proposes a methodological approach to combining various systems of ships into a single complex model. This model allows combining models of ship systems of various levels (microlevel, macrolevel, metalevel, megalevel). The work provides examples of models of such multi-level energy systems. These are energy systems composed of an electric generator, a diesel engine, a propeller shaft, and algorithms used for operating the common parts of the ship’s electric power system and a piston wear process. Analytical, structural, numerical, and object-oriented models were made for these objects. Each of these particular models describes a limited class of problems, has characteristic properties, and a mathematical structure. The work shows how particular models can be interconnected using a set-theoretic description. Particular models are combined into macrolevel models, whose output parameters are quantities that are by no means related. The macrolevel models are interrelated using control models. Control models belong to the metalevel and allow for assigning settings and response thresholds to algorithms used in automation systems. Such a model (megalevel model) allows, ultimately, investigating the dynamics of the entire system as a whole and managing it.
- Open Access
- 1 December 2023
- Published by MDPI AG in World Electric Vehicle Journal
- Vol. 14 (12) , 334
Determination of the Reliability of Urban Electric Transport Running Autonomously through Diagnostic Parameters
The urban transport network involves complex processes, operating 24 h a day and 365 days a year. The sustainable development of the urban transport network using electric buses and trolleybuses that run autonomously is an urgent task since the transport network performs integral social functions and is the transport artery of any urban center. The social and economic life of a city as a whole depends on the reliability of the transportation network. A theory is proposed for the technical and economic evaluation of reliability improvement in electric buses and trolleybuses running autonomously, which enables the determination of the reliability parameters of electric buses and forecasts for the future from the point of view of optimal economic costs for the operation of electric equipment in electric buses. As a result of the application of the proposed theory, it was found that increasing the reliability of the transportation fleet can lead to a decrease in both specific operating costs and capital investments in the development of the fleet. This is achieved as a result of increasing the annual productivity of vehicles by reducing the time they are out of service to eliminate the consequences of failures and carry out maintenance and repair. The conducted experiments confirmed that the theory and methodology of optimal reliability level selection not only enable the rational use of the material resources of the urban transport network but also the release of funds for its scientific and technical development by reducing the number of failures in the electrical equipment of transport systems by 14%.
- 1 December 2023
- Published by MDPI AG in World Electric Vehicle Journal
- Vol. 14 (12) , 334
Open AccessDetermination of the Reliability of Urban Electric Transport Running Autonomously through Diagnostic Parameters
The urban transport network involves complex processes, operating 24 h a day and 365 days a year. The sustainable development of the urban transport network using electric buses and trolleybuses that run autonomously is an urgent task since the transport network performs integral social functions and is the transport artery of any urban center. The social and economic life of a city as a whole depends on the reliability of the transportation network. A theory is proposed for the technical and economic evaluation of reliability improvement in electric buses and trolleybuses running autonomously, which enables the determination of the reliability parameters of electric buses and forecasts for the future from the point of view of optimal economic costs for the operation of electric equipment in electric buses. As a result of the application of the proposed theory, it was found that increasing the reliability of the transportation fleet can lead to a decrease in both specific operating costs and capital investments in the development of the fleet. This is achieved as a result of increasing the annual productivity of vehicles by reducing the time they are out of service to eliminate the consequences of failures and carry out maintenance and repair. The conducted experiments confirmed that the theory and methodology of optimal reliability level selection not only enable the rational use of the material resources of the urban transport network but also the release of funds for its scientific and technical development by reducing the number of failures in the electrical equipment of transport systems by 14%.
- Open Access
Designing the Optimal Configuration of a Small Power System for Autonomous Power Supply of Weather Station Equipment
Autonomous power systems serving remote areas with weather stations with small settlements are characterized by a fairly high cost of generating electricity and the purchase and delivery of fuel. In addition, diesel power plants require regular maintenance, have a relatively short service life during continuous operation and produce a large amount of emissions into the environment. This article discusses various methods of placing solar panels in the space for the autonomous power supply of weather station equipment. The principles of these methods are described and their advantages and disadvantages are outlined. The optimal algorithms of functioning for photomodules are described and their comparison regarding the main, significant parameters is carried out. The choice of the most effective algorithm for use at a weather station is made. The effective positioning of solar panels is also calculated, and positioning conditions are determined depending on the territorial location and various environmental conditions. Simulation of the power supply system of a weather station consisting of solar panels, batteries and inverters is performed. As a result, a practical example of the application of the method of selecting the optimal composition of equipment for a hybrid power system of a weather station territorially located in Siberia with different configurations of equipment is considered. In numerical terms, it was possible to reduce the cost of power equipment operation by more than 60% with a fairly low payback period of 5.5 years and an increased reliability of the power system, which is very important for autonomous power systems of northern weather stations.
Open AccessDesigning the Optimal Configuration of a Small Power System for Autonomous Power Supply of Weather Station Equipment
Autonomous power systems serving remote areas with weather stations with small settlements are characterized by a fairly high cost of generating electricity and the purchase and delivery of fuel. In addition, diesel power plants require regular maintenance, have a relatively short service life during continuous operation and produce a large amount of emissions into the environment. This article discusses various methods of placing solar panels in the space for the autonomous power supply of weather station equipment. The principles of these methods are described and their advantages and disadvantages are outlined. The optimal algorithms of functioning for photomodules are described and their comparison regarding the main, significant parameters is carried out. The choice of the most effective algorithm for use at a weather station is made. The effective positioning of solar panels is also calculated, and positioning conditions are determined depending on the territorial location and various environmental conditions. Simulation of the power supply system of a weather station consisting of solar panels, batteries and inverters is performed. As a result, a practical example of the application of the method of selecting the optimal composition of equipment for a hybrid power system of a weather station territorially located in Siberia with different configurations of equipment is considered. In numerical terms, it was possible to reduce the cost of power equipment operation by more than 60% with a fairly low payback period of 5.5 years and an increased reliability of the power system, which is very important for autonomous power systems of northern weather stations.
- Top Cited PapersOpen Access
Overview of Methods for Enhanced Oil Recovery from Conventional and Unconventional Reservoirs
In world practice, the role of reproduction of raw material base of oil production by implementing modern methods of oil recovery enhancement (thermal, gas, chemical, microbiological) on the basis of innovative techniques and technologies is rapidly growing and is becoming more important. It is concluded that at present, the priority of increasing oil reserves in world oil production is the development and industrial introduction of modern integrated methods of enhanced oil recovery, which can provide a synergistic effect in the development of new and developed oil fields. This article presents a review and comparative analysis of theoretical and practical methods of improving oil recovery of conventional and unconventional reservoirs. The paper examines in detail methods of improving oil recovery, taking into account the factors of enhanced oil recovery of oil reservoirs. Considered the main methods and technologies currently used to develop oil fields and recommendations for their effective use, taking into account the variety of external factors of oil production: the geological structure of the reservoir, its volume, and properties of oils. It is shown that there is no universal method of oil reservoir development, and it must be chosen after a thorough feasibility study among several proposed models. When describing the methods of enhanced oil recovery, special attention is also paid to the physical processes that occur as a result of applying the technology. In conclusion, the positive and negative characteristics of the presented methods included in EOR are presented, and recommendations that may influence the choice of practical solutions for engineers and oil producers are given. Conclusions are made that development systems, placement and choice of operating mode of wells essentially depend on the geological structure of the reservoir, its volume and properties of oils. An important role in this is the construction of a geological model of the production facility. The used hydrodynamic models of development are based on physical laws, about which oil producers sometimes don’t even suspect, and the authors of the models are not always able to convey it to the real producers. The authors consider it reasonable to make a logical generalizing conclusion that understanding processes occurring in the reservoir and taking appropriate measures for optimization and intensification of oil production will allow making oil production as effective as possible.
Top Cited PapersOpen AccessOverview of Methods for Enhanced Oil Recovery from Conventional and Unconventional Reservoirs
In world practice, the role of reproduction of raw material base of oil production by implementing modern methods of oil recovery enhancement (thermal, gas, chemical, microbiological) on the basis of innovative techniques and technologies is rapidly growing and is becoming more important. It is concluded that at present, the priority of increasing oil reserves in world oil production is the development and industrial introduction of modern integrated methods of enhanced oil recovery, which can provide a synergistic effect in the development of new and developed oil fields. This article presents a review and comparative analysis of theoretical and practical methods of improving oil recovery of conventional and unconventional reservoirs. The paper examines in detail methods of improving oil recovery, taking into account the factors of enhanced oil recovery of oil reservoirs. Considered the main methods and technologies currently used to develop oil fields and recommendations for their effective use, taking into account the variety of external factors of oil production: the geological structure of the reservoir, its volume, and properties of oils. It is shown that there is no universal method of oil reservoir development, and it must be chosen after a thorough feasibility study among several proposed models. When describing the methods of enhanced oil recovery, special attention is also paid to the physical processes that occur as a result of applying the technology. In conclusion, the positive and negative characteristics of the presented methods included in EOR are presented, and recommendations that may influence the choice of practical solutions for engineers and oil producers are given. Conclusions are made that development systems, placement and choice of operating mode of wells essentially depend on the geological structure of the reservoir, its volume and properties of oils. An important role in this is the construction of a geological model of the production facility. The used hydrodynamic models of development are based on physical laws, about which oil producers sometimes don’t even suspect, and the authors of the models are not always able to convey it to the real producers. The authors consider it reasonable to make a logical generalizing conclusion that understanding processes occurring in the reservoir and taking appropriate measures for optimization and intensification of oil production will allow making oil production as effective as possible.
- Top Cited PapersOpen Access
Study of Supercapacitors Built in the Start-Up System of the Main Diesel Locomotive
A successful guaranteed launch of a mainline diesel locomotive is one of the most important and urgent problems of the rolling stock operation. Improvement of the start-up system of the main diesel locomotive when using a supercapacitor allows multiple restarts of diesel locomotives, meaning that the operation of the diesel locomotive can be stopped several times without wasting fuel in idle operations. In this study, we simulated the electric starting circuit of a diesel locomotive with a block of supercapacitors using the Matlab Simulink program. The simulation results show that using only a supercapacitor in the start-up system is impossible. Even though the supercapacitor produces the required current and voltage, its operating time is extremely insufficient. Using a storage battery along with a supercapacitor in the diesel locomotive start-up system is most effective. This reduces the peak current load on the standard battery. The article suggests an effective principle for starting a mainline diesel locomotive and provides an effective circuit solution involving a supercapacitor. Based on the booster stabilizer scheme, a new scheme was modeled to study the successful launch of a diesel locomotive that has various start-up systems. Applying a supercapacitor in the start-up system of a main diesel locomotive is proposed and the results of its use are presented. In addition, this study defines the basic requirements for using a system based on a battery in conjunction with a supercapacitor. Characteristics such as the temperature range of the system are shown.
Top Cited PapersOpen AccessStudy of Supercapacitors Built in the Start-Up System of the Main Diesel Locomotive
A successful guaranteed launch of a mainline diesel locomotive is one of the most important and urgent problems of the rolling stock operation. Improvement of the start-up system of the main diesel locomotive when using a supercapacitor allows multiple restarts of diesel locomotives, meaning that the operation of the diesel locomotive can be stopped several times without wasting fuel in idle operations. In this study, we simulated the electric starting circuit of a diesel locomotive with a block of supercapacitors using the Matlab Simulink program. The simulation results show that using only a supercapacitor in the start-up system is impossible. Even though the supercapacitor produces the required current and voltage, its operating time is extremely insufficient. Using a storage battery along with a supercapacitor in the diesel locomotive start-up system is most effective. This reduces the peak current load on the standard battery. The article suggests an effective principle for starting a mainline diesel locomotive and provides an effective circuit solution involving a supercapacitor. Based on the booster stabilizer scheme, a new scheme was modeled to study the successful launch of a diesel locomotive that has various start-up systems. Applying a supercapacitor in the start-up system of a main diesel locomotive is proposed and the results of its use are presented. In addition, this study defines the basic requirements for using a system based on a battery in conjunction with a supercapacitor. Characteristics such as the temperature range of the system are shown.
- Top Cited PapersOpen Access
- 7 April 2023
- Published by MDPI AG in Applied Sciences
- Vol. 13 (8) , 4671
Reducing Oscillations in Suspension of Mine Monorail Track
Purpose: The goal of this work is to reduce the effect of dynamic loads on the mine timbering through the use of the elastic devices contained in the monorail suspension and to justify their parameters. Methods and materials: The article considers the developed mathematical model of vertical oscillations of the monorail track, which allows setting the interconnection between the rolling stock parameters and dynamic loads in the suspension. At vertical oscillations of the monorail and under the effect of harmonic disturbing force caused by the movement of the suspension, the system of the monorail suspension can be represented in the form of a dual-mass system. Results: As a result, the equations for oscillation amplitudes of the monorail elements were obtained and damping coefficient of suspension was defined. The obtained results suggest setting reasonable parameters of the monorail fastening, which offers the possibility to decrease dynamic loads occurring during the operation of the mine suspended monorail tracks. The proposed monorail suspension makes it possible to reduce the dynamic loads formed during the movement of the rolling stock by 30–40% and can be used to modernize existing mine suspended monorails. Discussion: Analysis of the obtained results shows that in order to reduce the vibration amplitudes of a suspended monorail mine, it is appropriate to use suspension systems for rolling stock and a monorail track, consisting of elastic elements. The parameters required for this can be determined using the proposed method, and required rigidity of the monorail track is provided by embedding elastic supports into its suspension system. Conclusions: The obtained results allow setting reasonable parameters of the monorail fastening of the mine suspended monorail tracks. The proposed monorail suspension makes it possible to minimize the dynamic loads formed during the movement of rolling stock and can be used to modernize existing mine suspension monorails.
- 7 April 2023
- Published by MDPI AG in Applied Sciences
- Vol. 13 (8) , 4671
Top Cited PapersOpen AccessReducing Oscillations in Suspension of Mine Monorail Track
Purpose: The goal of this work is to reduce the effect of dynamic loads on the mine timbering through the use of the elastic devices contained in the monorail suspension and to justify their parameters. Methods and materials: The article considers the developed mathematical model of vertical oscillations of the monorail track, which allows setting the interconnection between the rolling stock parameters and dynamic loads in the suspension. At vertical oscillations of the monorail and under the effect of harmonic disturbing force caused by the movement of the suspension, the system of the monorail suspension can be represented in the form of a dual-mass system. Results: As a result, the equations for oscillation amplitudes of the monorail elements were obtained and damping coefficient of suspension was defined. The obtained results suggest setting reasonable parameters of the monorail fastening, which offers the possibility to decrease dynamic loads occurring during the operation of the mine suspended monorail tracks. The proposed monorail suspension makes it possible to reduce the dynamic loads formed during the movement of the rolling stock by 30–40% and can be used to modernize existing mine suspended monorails. Discussion: Analysis of the obtained results shows that in order to reduce the vibration amplitudes of a suspended monorail mine, it is appropriate to use suspension systems for rolling stock and a monorail track, consisting of elastic elements. The parameters required for this can be determined using the proposed method, and required rigidity of the monorail track is provided by embedding elastic supports into its suspension system. Conclusions: The obtained results allow setting reasonable parameters of the monorail fastening of the mine suspended monorail tracks. The proposed monorail suspension makes it possible to minimize the dynamic loads formed during the movement of rolling stock and can be used to modernize existing mine suspension monorails.
- Open Access
Complex Assessment of X-ray Diffraction in Crystals with Face-Centered Silicon Carbide Lattice
X-ray diffraction analysis is essential in studying stacking faults. Most of the techniques used for this purpose are based on theoretical studies. These studies suggest that the observed diffraction patterns are caused by random stacking faults in crystals. In reality, however, the condition of randomness for stacking faults may be violated. The purpose of the study was to develop a technique that can be used to calculate the diffraction effects of the axis of the thin plates of twin, new phases, as well as other variations in defective structures. Materials and methods. This was achieved through modern X-ray diffraction methods using differential equations (transformations and Fourier transforms) and the construction of the Ewald sphere, mathematical analysis, mathematical logic, and mathematical modeling (complex Markov chain). Conclusion. The study made it possible to develop a technique for the calculation of the diffraction effects of the axis of the thin plates of twin, new phases and other variations in defective structures. The technique makes it possible to solve several complex, urgent problems related to the calculation of X-ray diffraction for crystals with face-centered lattices containing different types of stacking faults. At the same time, special attention was paid to the correlations between the relative positions of faults. The calculations showed that the proposed method can help to determine the nature and structure of stacking faults by identifying the partial and vertex dislocations limiting them in twin crystals with a face-centered cubic structure of silicon carbide based on X-ray diffraction analysis.
Open AccessComplex Assessment of X-ray Diffraction in Crystals with Face-Centered Silicon Carbide Lattice
X-ray diffraction analysis is essential in studying stacking faults. Most of the techniques used for this purpose are based on theoretical studies. These studies suggest that the observed diffraction patterns are caused by random stacking faults in crystals. In reality, however, the condition of randomness for stacking faults may be violated. The purpose of the study was to develop a technique that can be used to calculate the diffraction effects of the axis of the thin plates of twin, new phases, as well as other variations in defective structures. Materials and methods. This was achieved through modern X-ray diffraction methods using differential equations (transformations and Fourier transforms) and the construction of the Ewald sphere, mathematical analysis, mathematical logic, and mathematical modeling (complex Markov chain). Conclusion. The study made it possible to develop a technique for the calculation of the diffraction effects of the axis of the thin plates of twin, new phases and other variations in defective structures. The technique makes it possible to solve several complex, urgent problems related to the calculation of X-ray diffraction for crystals with face-centered lattices containing different types of stacking faults. At the same time, special attention was paid to the correlations between the relative positions of faults. The calculations showed that the proposed method can help to determine the nature and structure of stacking faults by identifying the partial and vertex dislocations limiting them in twin crystals with a face-centered cubic structure of silicon carbide based on X-ray diffraction analysis.