Kumar Abhishek Singh
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Kumar Abhishek Singh has a total of 9 co-authors. Here are the top co-authors by number of shared publications:
- Kalpana Chaudhary
Department of Electrical Engineering Indian Institute of Technology (BHU) Varanasi India
4 shared publications Ashish Prajapati
Department of Electrical Engineering, IIT (BHU) Varanasi, Varanasi, India
1 shared publication- Ayushi Chaudhary
Department of Electrical Engineering, Indian Institute of Technology Kanpur, Kanpur, Uttar Pradesh, India
1 shared publication - Baseem Khan
Department of Electrical and Computer Engineering, Hawassa University, Hawassa, Ethiopia
1 shared publication Batta Sivaprasad
Department of Electrical Engineering, Indian Institute of Technology (BHU) Varanasi, Varanasi, Uttar Pradesh, India
1 shared publication- Mukesh Kumar
Department of Electrical Engineering, Indian Institute of Technology (BHU), Varanasi, Uttar Pradesh, India
1 shared publication
Latest Publications
- Open Access
- 6 November 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 11, 124068-124080
A Flexible Virtual Inertia and Damping Control Strategy for Virtual Synchronous Generator for Effective Utilization of Energy Storage
This paper presents a flexible virtual inertia and damping control strategy for a virtual synchronous generator (VSG) for the effective utilization of energy storage. Due to their low inertia and low kinetic energy, power electronics-based renewable energy sources are becoming more and more prevalent, which poses major dependability issues for the grid. However, the typical synchronous generator has the ability to adjust to changes in the grid frequency and voltage thanks to load frequency management and an automatic voltage regulator. So, emulating the synchronous machine characteristics in the power electronics-based converter system increases the stability of the grid and further increases the renewable energy penetration in the grid. However, VSG power and frequency oscillates when a sudden disturbance in the power demand occurs in the distributed generation system. This article focuses on minimizing the frequency oscillations as well as power oscillations of VSG during transient conditions or disturbances. Initially, the impact of varying inertia and damping on the active power control loop of VSG is investigated. In addition, the parameters of the VSG are designed in order to minimize the requirement of discharge/charge from the energy storage. So, in this paper, a control strategy with flexible virtual inertia and damping coefficient is designed for optimizing the energy storage unit to support frequency stability. The proposed control method is verified in the developed experimental prototype. In addition, proposed control algorithm is compared with the currently available adaptive control approaches like adaptive inertia control (adaptive J control) and alternating inertia and damping (alternating J and DP control) based VSG and observed that the energy storage requirement and the oscillations in the active power and frequency are minimum in the proposed control method as compared to the other two methods.
- 6 November 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 11, 124068-124080
Open AccessA Flexible Virtual Inertia and Damping Control Strategy for Virtual Synchronous Generator for Effective Utilization of Energy Storage
This paper presents a flexible virtual inertia and damping control strategy for a virtual synchronous generator (VSG) for the effective utilization of energy storage. Due to their low inertia and low kinetic energy, power electronics-based renewable energy sources are becoming more and more prevalent, which poses major dependability issues for the grid. However, the typical synchronous generator has the ability to adjust to changes in the grid frequency and voltage thanks to load frequency management and an automatic voltage regulator. So, emulating the synchronous machine characteristics in the power electronics-based converter system increases the stability of the grid and further increases the renewable energy penetration in the grid. However, VSG power and frequency oscillates when a sudden disturbance in the power demand occurs in the distributed generation system. This article focuses on minimizing the frequency oscillations as well as power oscillations of VSG during transient conditions or disturbances. Initially, the impact of varying inertia and damping on the active power control loop of VSG is investigated. In addition, the parameters of the VSG are designed in order to minimize the requirement of discharge/charge from the energy storage. So, in this paper, a control strategy with flexible virtual inertia and damping coefficient is designed for optimizing the energy storage unit to support frequency stability. The proposed control method is verified in the developed experimental prototype. In addition, proposed control algorithm is compared with the currently available adaptive control approaches like adaptive inertia control (adaptive J control) and alternating inertia and damping (alternating J and DP control) based VSG and observed that the energy storage requirement and the oscillations in the active power and frequency are minimum in the proposed control method as compared to the other two methods.
- 23 February 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industry Applications
- Vol. 58 (5) , 5558-5567
Integrated Quadruple Output Synchronous Buck Converter for E-Mobility Application
A nonisolated integrated multiple output synchronous buck converter is proposed in this article to cater the auxiliary power supply requirements of e-mobility. The converter provides independently controlled multiple outputs with reduced switch count as compared to conventional separate buck converters as well as conventional synchronous buck converter. The operating principle and working of the proposed converter are discussed in detail for better understanding. As the dynamic behavior of the converter is similar to the conventional buck converter, a simple controller is designed and implemented in this work. The converter is simulated in MATLAB-Simulink. A laboratory prototype of single input–quadruple output (SIQO) converter is developed and operated under closed loop condition to validate and demonstrate its advantages. The prototype is developed by designing two inductors on a single core for increased compactness and reduced cost of the converter. Each output of the converter can be independently controlled by varying the duty ratio of the related switch, thereby eliminating the effective cross regulation problem. The efficiency of the proposed SIQO converter is 93.6%, with four output ports, which is higher than its category of converters reported earlier. A significant improvement in the calculated efficiency is observed with the replacement of conventional switches and diodes of the converter by SiC switches (96.1%).
- 23 February 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industry Applications
- Vol. 58 (5) , 5558-5567
Integrated Quadruple Output Synchronous Buck Converter for E-Mobility Application
A nonisolated integrated multiple output synchronous buck converter is proposed in this article to cater the auxiliary power supply requirements of e-mobility. The converter provides independently controlled multiple outputs with reduced switch count as compared to conventional separate buck converters as well as conventional synchronous buck converter. The operating principle and working of the proposed converter are discussed in detail for better understanding. As the dynamic behavior of the converter is similar to the conventional buck converter, a simple controller is designed and implemented in this work. The converter is simulated in MATLAB-Simulink. A laboratory prototype of single input–quadruple output (SIQO) converter is developed and operated under closed loop condition to validate and demonstrate its advantages. The prototype is developed by designing two inductors on a single core for increased compactness and reduced cost of the converter. Each output of the converter can be independently controlled by varying the duty ratio of the related switch, thereby eliminating the effective cross regulation problem. The efficiency of the proposed SIQO converter is 93.6%, with four output ports, which is higher than its category of converters reported earlier. A significant improvement in the calculated efficiency is observed with the replacement of conventional switches and diodes of the converter by SiC switches (96.1%).
- Open Access
- 31 January 2022
- Published by Wiley in International Transactions on Electrical Energy Systems
- Vol. 2022, 1-20
Regenerative Braking in Electric Vehicle Using Quadratic Gain Bidirectional Converter
The manuscript proposes a quadratic gain bidirectional converter (QGBC). The proposed converter is operated in two different stages—step-up (motoring) and step-down (regenerative braking)—which can be employed in electric vehicle (EV) applications. The converter is operated in the continuous inductor current mode (CICM). For regenerative braking (RB) of permanent magnet brushless DC (PMBLDC) motor, the self-inductance of the motor is exploiting to step up the back electromagnetic force (EMF) of the motor to extract the energy even at low rotor speed. The design parameters of the converter are selected as battery voltage , output voltage , output power , and switching frequency . The design system is simulated using MATLAB/Simulink. Finally, a 1 kW prototype is developed for validation and performance analysis of the converter. The converter operates at maximum efficiency of 95% during step-up operation of the converter. A DSP microcontroller TMS320F28335 is used to control the switches of the converter in the experimental setup.
- 31 January 2022
- Published by Wiley in International Transactions on Electrical Energy Systems
- Vol. 2022, 1-20
Open AccessRegenerative Braking in Electric Vehicle Using Quadratic Gain Bidirectional Converter
The manuscript proposes a quadratic gain bidirectional converter (QGBC). The proposed converter is operated in two different stages—step-up (motoring) and step-down (regenerative braking)—which can be employed in electric vehicle (EV) applications. The converter is operated in the continuous inductor current mode (CICM). For regenerative braking (RB) of permanent magnet brushless DC (PMBLDC) motor, the self-inductance of the motor is exploiting to step up the back electromagnetic force (EMF) of the motor to extract the energy even at low rotor speed. The design parameters of the converter are selected as battery voltage , output voltage , output power , and switching frequency . The design system is simulated using MATLAB/Simulink. Finally, a 1 kW prototype is developed for validation and performance analysis of the converter. The converter operates at maximum efficiency of 95% during step-up operation of the converter. A DSP microcontroller TMS320F28335 is used to control the switches of the converter in the experimental setup.
- 18 October 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Emerging and Selected Topics in Power Electronics
- Vol. 10 (4) , 4763-4770
High-Gain Compact Interleaved Boost Converter With Reduced Voltage Stress for PV Application
This article proposes an interleaved, highly efficient, high-gain modified boost converter. High-gain and transformerless converter operation makes the converter suitable for integrating photovoltaic (PV) power to standalone dc microgrid. A coupled inductor is used with two diodes and one switch per phase with a common clamping capacitor to modify the conventional boost converter. The common clamping capacitor and the coupled inductor reduce the converter’s component count and size; thus, high efficiency is achieved at a low cost. The proposed converter achieves a high step-up gain and low voltage stress on switches. Interleaved converters are deemed ideal for PV power extraction as they exhibit low input current ripple. A 900-W prototype of a two-phase interleaved modified boost converter is designed and developed to verify the working principle of the converter and performance testing.
- 18 October 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Emerging and Selected Topics in Power Electronics
- Vol. 10 (4) , 4763-4770
High-Gain Compact Interleaved Boost Converter With Reduced Voltage Stress for PV Application
This article proposes an interleaved, highly efficient, high-gain modified boost converter. High-gain and transformerless converter operation makes the converter suitable for integrating photovoltaic (PV) power to standalone dc microgrid. A coupled inductor is used with two diodes and one switch per phase with a common clamping capacitor to modify the conventional boost converter. The common clamping capacitor and the coupled inductor reduce the converter’s component count and size; thus, high efficiency is achieved at a low cost. The proposed converter achieves a high step-up gain and low voltage stress on switches. Interleaved converters are deemed ideal for PV power extraction as they exhibit low input current ripple. A 900-W prototype of a two-phase interleaved modified boost converter is designed and developed to verify the working principle of the converter and performance testing.
- Open Access
- 30 December 2020
- Published by Institution of Engineering and Technology (IET) in IET Power Electronics
- Vol. 14 (2) , 302-312
Design and development of a new three‐phase AC‐DC single‐stage wind energy conversion system
The prevalent use of the diode bridge rectifier in three phase wind energy conversion systems decreases the efficiency of the power generation. In standalone wind energy generation, bridgeless converters can address this problem by eliminating the front‐end diode bridge rectifier. This work presents a novel single‐stage three‐phase bridgeless AC to DC c̀uk converter for wind energy conversion systems. The proposed converter is designed to work in discontinuous inductor current mode because of its inherent power factor correction and less harmonic distortion. Using body‐diodes of the MOSFETs per phase component reduction is also done in this converter. A unique maximum power point tracking technique is developed for this converter using three‐phase voltages and currents, instead of the DC link states. A wind energy emulation system using a DC motor and self excited induction generator is used to test the laboratory prototype of the proposed converter.
- 30 December 2020
- Published by Institution of Engineering and Technology (IET) in IET Power Electronics
- Vol. 14 (2) , 302-312
Open AccessDesign and development of a new three‐phase AC‐DC single‐stage wind energy conversion system
The prevalent use of the diode bridge rectifier in three phase wind energy conversion systems decreases the efficiency of the power generation. In standalone wind energy generation, bridgeless converters can address this problem by eliminating the front‐end diode bridge rectifier. This work presents a novel single‐stage three‐phase bridgeless AC to DC c̀uk converter for wind energy conversion systems. The proposed converter is designed to work in discontinuous inductor current mode because of its inherent power factor correction and less harmonic distortion. Using body‐diodes of the MOSFETs per phase component reduction is also done in this converter. A unique maximum power point tracking technique is developed for this converter using three‐phase voltages and currents, instead of the DC link states. A wind energy emulation system using a DC motor and self excited induction generator is used to test the laboratory prototype of the proposed converter.