Junxiao Feng
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Junxiao Feng has a total of 22 co-authors. Here are the top co-authors by number of shared publications:
Huanbao Fan
School of Energy And Environmental Engineering, Shunde Graduate School, University of Science and Technology Beijing, Beijing 100083, China
4 shared publicationsJun Gao
Technology Center of Ansteel Co., Ltd, Anshan, Liaoning 114003, China
4 shared publicationsWei Bai
3 shared publicationsWeidong Li
3 shared publicationsChangpeng Liu
2 shared publicationsOmid AliAkbaria
Department of Mechanical Engineering, Khomeinishahr Branch, Islamic Azad University, Khomeinishahr, Iran
2 shared publications
Latest Publications
- 22 May 2024
- Published by Springer Nature in Journal of Iron and Steel Research International
- Vol. 32 (3) , 707-719
Optimization of reheating furnace rolling delay strategies based on a minimum energy consumption principle
- 22 May 2024
- Published by Springer Nature in Journal of Iron and Steel Research International
- Vol. 32 (3) , 707-719
Optimization of reheating furnace rolling delay strategies based on a minimum energy consumption principle
- Open Access
- 1 January 2022
- Published by National Library of Serbia in Thermal Science
- Vol. 26 (5 Part A) , 3787-3801
Numerical simulation on heating performance and emission characteristics of a new multi-stage dispersed burner for gas-fired radiant tubes
To enhance the temperature uniformity and NOx reduction performance of the gas-fired radiant tubes, we proposed a new multi-stage dispersed burner based on fuel-staging combustion technology in this study. The effect of fuel nozzle structural parameters, including secondary fuel nozzle distance, D, (30 mm, 50 mm, 70 mm), secondary fuel nozzle diameter, ds, (2-6 mm), and tertiary fuel nozzle diameter, dt, (2.5 mm, 5 mm, 7.5 mm, 10 mm) on the flow field, temperature distribution, NOx generation and thermal efficiency were analyzed by numerical simulations. The results show that the multi-stage dispersed fuel nozzle could slow down the combustion rate and form a low oxygen dilution zone in the reaction process, reducing the maximum combustion temperature and NOx emission. With the increase of the secondary fuel nozzle distance, the NOx concentration at the outlet decreased from 69.0 ppm to 54.6 ppm, and a decrease of 20.9%. When the secondary fuel nozzle diameter increased from 2-6 mm, the maximum wall temperature difference gradually increased 72.8-76.3 K. The NOx emission at the outlet first decreased, then increased, and was as low as 45.6 ppm at a 5 mm diameter. Furthermore, increasing the tertiary fuel nozzle diameter could reduce the maximum wall temperature difference and NOx emission, and improve thermal efficiency. When dt = 7.5 mm, the overall performance of the radiant tube was the best, and the outlet NOx concentration, wall temperature difference and thermal efficiency were 46.1 ppm, 73.0 K, 63.7%, respectively.
- 1 January 2022
- Published by National Library of Serbia in Thermal Science
- Vol. 26 (5 Part A) , 3787-3801
Open AccessNumerical simulation on heating performance and emission characteristics of a new multi-stage dispersed burner for gas-fired radiant tubes
To enhance the temperature uniformity and NOx reduction performance of the gas-fired radiant tubes, we proposed a new multi-stage dispersed burner based on fuel-staging combustion technology in this study. The effect of fuel nozzle structural parameters, including secondary fuel nozzle distance, D, (30 mm, 50 mm, 70 mm), secondary fuel nozzle diameter, ds, (2-6 mm), and tertiary fuel nozzle diameter, dt, (2.5 mm, 5 mm, 7.5 mm, 10 mm) on the flow field, temperature distribution, NOx generation and thermal efficiency were analyzed by numerical simulations. The results show that the multi-stage dispersed fuel nozzle could slow down the combustion rate and form a low oxygen dilution zone in the reaction process, reducing the maximum combustion temperature and NOx emission. With the increase of the secondary fuel nozzle distance, the NOx concentration at the outlet decreased from 69.0 ppm to 54.6 ppm, and a decrease of 20.9%. When the secondary fuel nozzle diameter increased from 2-6 mm, the maximum wall temperature difference gradually increased 72.8-76.3 K. The NOx emission at the outlet first decreased, then increased, and was as low as 45.6 ppm at a 5 mm diameter. Furthermore, increasing the tertiary fuel nozzle diameter could reduce the maximum wall temperature difference and NOx emission, and improve thermal efficiency. When dt = 7.5 mm, the overall performance of the radiant tube was the best, and the outlet NOx concentration, wall temperature difference and thermal efficiency were 46.1 ppm, 73.0 K, 63.7%, respectively.
- Open Access
- 4 June 2021
- Published by EDP Sciences in E3S Web of Conferences
- Vol. 267, 02053
Numerical simulation of NO emission reduction in coke oven regenerator with synergistic SNCR/SCR process
According to the temperature gradient distribution characteristics of the regenerator of the coke oven, a method of synergistic the SNCR/SCR process inside the regenerator to achieve NO emission reduction was proposed in this work. Based on the verification of SNCR and SCR models, the NH3/NO concentration field and the spatial distribution characteristics of NO in the process of SNCR, SCR, and SNCR+SCR were studied. The conclusion shows that the synergistic SNCR and SCR processes had achieved NO reduction by 64.3% and 37.1%, respectively. However, the increase in reaction temperature caused by the change of injection position resulted in a 0.4% decrease in SNCR+SCR compared to SNCR. It was also found that temperature dramatically influences the SNCR process and the reductant injection position. Limited by the structure of the regenerator and the catalyst coating area, the SCR process exhibited a low NO reduction ability. The SNCR+SCR process should focus on improving the efficiency of the SCR process.
- 4 June 2021
- Published by EDP Sciences in E3S Web of Conferences
- Vol. 267, 02053
Open AccessNumerical simulation of NO emission reduction in coke oven regenerator with synergistic SNCR/SCR process
According to the temperature gradient distribution characteristics of the regenerator of the coke oven, a method of synergistic the SNCR/SCR process inside the regenerator to achieve NO emission reduction was proposed in this work. Based on the verification of SNCR and SCR models, the NH3/NO concentration field and the spatial distribution characteristics of NO in the process of SNCR, SCR, and SNCR+SCR were studied. The conclusion shows that the synergistic SNCR and SCR processes had achieved NO reduction by 64.3% and 37.1%, respectively. However, the increase in reaction temperature caused by the change of injection position resulted in a 0.4% decrease in SNCR+SCR compared to SNCR. It was also found that temperature dramatically influences the SNCR process and the reductant injection position. Limited by the structure of the regenerator and the catalyst coating area, the SCR process exhibited a low NO reduction ability. The SNCR+SCR process should focus on improving the efficiency of the SCR process.