Hiwa Golpira
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Hiwa Golpira has a total of 7 co-authors. Here are the top co-authors by number of shared publications:
Francisco Rovira-Más
Polytechnic University of Valencia, Valencia
1 shared publicationHêmin Golpîra
University of Kurdistan, Dept. Electrical Engineering. Sanandaj
1 shared publication- Hêmin Golpîra
Power Systems Modeling & Simulation Lab, Department of Electrical Engineering, University of Kurdistan, Sanandaj, Iran
1 shared publication Markus Demmel
Bavarian State Research Center for Agriculture Landesanstalt fuer Landetchnik Freising Germany
1 shared publicationParviz Rashidian
Department of Mathematics University of Kurdistan Sanandaj Kurdistan Iran
1 shared publication- Rafael Rubén Sola-Guirado
Department of Mechanics, Campus de Rabanales, University of Cordoba, 14014 Cordoba, Spain
1 shared publication
Latest Publications
- 12 July 2023
- Published by Wiley in Agronomy Journal
- Vol. 116 (3) , 855-860
Markov model planning on the adoption of an enhanced wheat cultivar
Predictions on the time needed to adopt new technologies can be used for planning purposes. These predictions should be calculated using a Markov planning model, which is a probabilistic approach to estimating the speed of adoption. In a research project, a data‐driven model was developed to simulate the adoption rate of an enhanced, drought‐resistant rain‐fed hard wheat (Triticum aestivum L.) cultivar in Kurdistan, Iran. The growers’ decision‐making on cultivar replacement was mapped onto the transition matrix, state probability, transition diagram, and tree of the states of the Markov process to compute the limiting probability of the stochastic model, thereby simulating the adoption rate of the wheat cultivar. The mathematical model, which achieves a convergence of 82% adoption for the enhanced wheat cultivar within 5 years, simulates farmers’ behavior and knowledge to enhance food security. Simulating the future of new technology in food and agricultural systems using the proposed methodology can assist policymakers in making informed decisions.
- 12 July 2023
- Published by Wiley in Agronomy Journal
- Vol. 116 (3) , 855-860
Markov model planning on the adoption of an enhanced wheat cultivar
Predictions on the time needed to adopt new technologies can be used for planning purposes. These predictions should be calculated using a Markov planning model, which is a probabilistic approach to estimating the speed of adoption. In a research project, a data‐driven model was developed to simulate the adoption rate of an enhanced, drought‐resistant rain‐fed hard wheat (Triticum aestivum L.) cultivar in Kurdistan, Iran. The growers’ decision‐making on cultivar replacement was mapped onto the transition matrix, state probability, transition diagram, and tree of the states of the Markov process to compute the limiting probability of the stochastic model, thereby simulating the adoption rate of the wheat cultivar. The mathematical model, which achieves a convergence of 82% adoption for the enhanced wheat cultivar within 5 years, simulates farmers’ behavior and knowledge to enhance food security. Simulating the future of new technology in food and agricultural systems using the proposed methodology can assist policymakers in making informed decisions.
- Open Access
- 13 February 2022
- Published by MDPI AG in Agriculture
- Vol. 12 (2) , 264
Data-Driven Simulator: Redesign of Chickpea Harvester Reels
Conventional redesign methodologies applied on the grain harvester headers for the mechanical harvesting of chickpeas cause its progress to not be as rapid and technological. This paper presents a hybrid modeling-optimization methodology to design harvester reels for efficient chickpea harvesting. The five fabricated headers were tested in both real and virtual modeling environments to optimize the operational parameters of the reel for minimum losses. Harvesting losses data gathered from chickpea fields over ten years of trials were fed into a fuzzy logic model, which in turn was merged with simulated annealing to develop a simulator. To this end, simulated annealing was used to produce combinations of reel diameter and number of bats, to be fed into the fuzzy model until achieving a minimum harvesting loss. The proposed model predicts the reel structure measured in-field evaluation, which fits well with the previously established mathematical model. A significant improvement in harvesting performance, 71% pod harvesting, validates the benefits of the proposed fuzzy-simulated annealing approach to optimize the design of grain harvester headers.
- 13 February 2022
- Published by MDPI AG in Agriculture
- Vol. 12 (2) , 264
Open AccessData-Driven Simulator: Redesign of Chickpea Harvester Reels
Conventional redesign methodologies applied on the grain harvester headers for the mechanical harvesting of chickpeas cause its progress to not be as rapid and technological. This paper presents a hybrid modeling-optimization methodology to design harvester reels for efficient chickpea harvesting. The five fabricated headers were tested in both real and virtual modeling environments to optimize the operational parameters of the reel for minimum losses. Harvesting losses data gathered from chickpea fields over ten years of trials were fed into a fuzzy logic model, which in turn was merged with simulated annealing to develop a simulator. To this end, simulated annealing was used to produce combinations of reel diameter and number of bats, to be fed into the fuzzy model until achieving a minimum harvesting loss. The proposed model predicts the reel structure measured in-field evaluation, which fits well with the previously established mathematical model. A significant improvement in harvesting performance, 71% pod harvesting, validates the benefits of the proposed fuzzy-simulated annealing approach to optimize the design of grain harvester headers.
- 16 April 2021
- Published by Instituto Nacional de Investigacion y Tecnologia Agraria y Alimentaria (INIA) in Spanish Journal of Agricultural Research
- Vol. 19 (1) , e0203
Mathematical model-based redesign of chickpea harvester reel
Aim of study: This paper presents a mathematical modeling approach to redesign the reels of chickpea harvesters for harvest efficiency.Area of study: A prototype chickpea harvester was designed and evaluated on the Dooshan farm of the University of Kurdistan, Sanandaj, Iran.Material and methods: The strategy used for reducing harvesting losses derived from the dynamic study of the reel applied to the chickpea harvester. The machine was designed such that bats of a power take-off (PTO)-powered reel, in conjunction with passive fingers, harvest pods from anchored plants and throw the pods into a hopper. The trochoid trajectory of the reel bats concerning reel kinematic index, and plant height and spacing was determined for redesigning the reel.Main results: This kinematic design allowed an estimation of the reel orientation at the time of impact. The experimentally validated model offers an accurate and low computational cost method to redesign harvester reels.Research highlights: The new chickpea harvester implemented with a four fixed-bat reel, a height of 40 cm above the ground for the reel axis, and featuring a kinematic index of 2.4 was capable of harvesting pods with harvesting efficiency of over 70%; a significant improvement in harvesting performance.
- 16 April 2021
- Published by Instituto Nacional de Investigacion y Tecnologia Agraria y Alimentaria (INIA) in Spanish Journal of Agricultural Research
- Vol. 19 (1) , e0203
Mathematical model-based redesign of chickpea harvester reel
Aim of study: This paper presents a mathematical modeling approach to redesign the reels of chickpea harvesters for harvest efficiency.Area of study: A prototype chickpea harvester was designed and evaluated on the Dooshan farm of the University of Kurdistan, Sanandaj, Iran.Material and methods: The strategy used for reducing harvesting losses derived from the dynamic study of the reel applied to the chickpea harvester. The machine was designed such that bats of a power take-off (PTO)-powered reel, in conjunction with passive fingers, harvest pods from anchored plants and throw the pods into a hopper. The trochoid trajectory of the reel bats concerning reel kinematic index, and plant height and spacing was determined for redesigning the reel.Main results: This kinematic design allowed an estimation of the reel orientation at the time of impact. The experimentally validated model offers an accurate and low computational cost method to redesign harvester reels.Research highlights: The new chickpea harvester implemented with a four fixed-bat reel, a height of 40 cm above the ground for the reel axis, and featuring a kinematic index of 2.4 was capable of harvesting pods with harvesting efficiency of over 70%; a significant improvement in harvesting performance.
- 2 August 2016
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 89 (5-8) , 1791-1798
Redesign and evaluation of an automatic fruit sorter
- 2 August 2016
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 89 (5-8) , 1791-1798
Redesign and evaluation of an automatic fruit sorter