ŞBŞilan Baturay

Şilan Baturay

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Şilan Baturay has a total of 18 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    The Effect of the Back Surface Field on the Performance of Cu3SnS4 Thin Film Solar Cell Modeled Using SCAPS-1D Software

    by Serap Yiğit Gezgin, Şilan Baturay, Shrouk E. Zaki, Hamdi Şükür Kiliç

    In this study, the PV performance of Au/BSF/CTS/CdS/i-ZnO/ITO thin-film solar cell (TFC) structure was systematically investigated using SCAPS-1D software. The effects of several critical parameters, including interface defect density, recombination mechanisms, absorber defect density, operating temperature, parasitic resistances, and different back surface field (BSF) layers, were comprehensively analyzed. The SCAPS-1D software results reveal that the photovoltaic performance is highly sensitive to the defect density at the absorber layer interface. When the interface defect density increased from 1012 cm−3 to 1016 cm−3, the open-circuit voltage (VOC) decreased from approximately 0.68 V to 0.45 V, while the power conversion efficiency (PCE) declined from nearly 19% to about 7%. Similarly, an increase in absorber defect density enhanced the Shockley–Read–Hall recombination rate, thereby reducing carrier lifetime and significantly deteriorating PV parameters. The influence of radiative and Auger recombination (BAuger) processes was also examined, revealing that higher recombination coefficients lead to substantial reductions in current density and efficiency due to increased carrier losses. Furthermore, the impact of parasitic resistances was evaluated, demonstrating that decrease the series resistance from 9.5 Ω·cm2 to 0.5 Ω·cm2 increased the fill factor (FF) from about 48% to nearly 78%, while the device efficiency improved to approximately 32%. In addition to these parameters, particular emphasis was placed on the investigation of different BSF materials to enhance back contact performance. Various BSF layers, including SnS, PbS, V2O5, and Sb2S3, were examined to improve band alignment and suppress minority carrier recombination at the rear interface. Among these materials, the SnS BSF layer provided the most favorable band alignment with the CTS absorber, leading to a notable improvement in PV parameters and increasing the efficiency to approximately 25%. Overall, the results demonstrate that optimizing defect densities, recombination mechanisms, parasitic resistances, and especially the selection of appropriate BSF materials plays a crucial role in improving the performance of CTS-based TFCs.


  • The Effect of Annealing on Structural, Optical, and Electrical Properties of Cu3SnS4 Thin Films Prepared by Spin Coat Method

    by Nuray Yıldız, Şilan Baturay, Canan Aytuğ Ava

    Cu 3 SnS 4 films were grown on glass substrates via method of spin coating, followed by annealing at 550 °C in a furnace under H₂S:Ar (1:9) sulfur rates of 30 and 40 sccm for 15, 30, and 60 minutes. The effect of the sulfur rate and annealing time on the structural, morphological, and optical behaviors of the samples was systematically investigated using X-ray diffraction (XRD), Raman spectroscopy, scanning electron microscopy (SEM), atomic force microscopy (AFM), photoluminescence (PL), Hall effect, and UV-Vis spectroscopy. The XRD patterns revealed that all the Cu 3 SnS 4 samples had a polycrystalline structure. The crystallite size, dislocation density, interplaner distance, micro-strain, and crystallite number of the Cu 3 SnS 4 samples were calculated from the XRD spectra. Among all the samples, the CTS sample annealed for 15 minutes under a 30 sccm H₂S:Ar (1:9) gas flow showed the best crystalline structure. The surface morphology of the samples showed spherical micro-crystal formations. Analysis of the Cu 3 SnS 4 samples indicated that the surfaces were composed of valley and peak regions. The valley regions appeared relatively smooth, while the peak regions displayed a crystal structure with specific orientations. When examining the energy band gap values, it is observed that the energy band gap of the films increases significantly with the increase in sulfur flow rate. PL analysis revealed emission peaks at approximately 1.41 eV and 1.80 eV, along with broad emission bands at 549 nm, 567 nm, 689.42 nm, and 882.6 nm. An increase in sulfur content led to a reduction in peak intensity, which is attributed to conduction band fluctuations and the formation of structural defects. The carrier concentration of the samples is found to be on the order of 10 17 cm −3 and 10 18 cm −3 , which is more appropriate for thin-film solar cells (TFCSs).


  • Open Access

    Enhanced Opto-Electronic Properties of Bi:CuO/n-Si Heterojunctions for Photodetector Applications

    by G. Sutcu, S. Yigit Gezgin, S. Baturay, H.S. Kilic

    An effective photodetector based on a family of p-type semiconductors with unique properties is still required by current trends in optoelectronics. The purpose of this study is to enhance the performance of p-type copper oxide films by doping them with bismuth. The pure copper oxide films were successfully fabricated with 1, 2, and 3 wt% of Bi by the spin coating method in an air atmosphere. Advanced techniques were used to describe the fabricated non-doped and Bi-doped CuO films to understand their structural, topological, and optical characteristics. X-ray diffraction patterns of non-doped and Bi-doped CuO films have demonstrated that they have polycrystalline structures, with a preference for growth in both (-111) and (200) orientations. Copper oxide film with 2% Bi doping exhibited the most uniform particle size distribution compared to others. While 3% Bi-doped CuO thin film exhibits the highest photon absorption, 2% Bi-doped CuO thin film transmits more photons. The direct band gaps of the non-doped and Bi-doped CuO samples were found between 1.77 and 1.94 eV. Copper oxide thin film with 2% Bi has the lowest refractive index. While the 2% Bi-doped CuO heterojunction photodetector shows the highest photosensitivity, responsivity, and detectivity, its rise and time are the lowest. Since 2% Bi-doped CuO film has a good crystal structure, large crystalline size, low particle boundary numbers, and a more homogeneous particle size distribution, the number of traps and defects in this thin film is low, and the recombination of charge carriers is limited. Thus, this thin-film-based heterojunction exhibited the best photodetector property, and the results of this work give a way to create effective photodetectors and adjust their performance over a broad range.


  • Open Access

    Numerical analysis of the thin film solar cell modelled based on In doped CdS semiconductor

    by Serap Yi̇ği̇t Gezgi̇n, Şilan Baturay, Hamdi Şükür Kiliç

    In this study, pure and 1%, 2% and %3 In-doped CdS thin films were produced by spray pyrolysis method. CdS is an n-type (II-VI group) semiconductor material and used as a buffer layer in solar cells. By doping In into CdS thin film, it was investigated how optical and crystalline behavior of thin film are changed. Using Moss and Herve&Vandamme and Ravindra relations, refractive indices and dielectric coefficients were investigated depending on the band gap of the obtained CdS sample. It has been observed that In element decreases the band gap of CdS thin film, improved its crystal structure and reduced its roughness. Therefore, 3% In doped CdS has gained a more ideal feature for use as an n-type semiconductor in solar cells. CIGS/In doped CdS solar cell was modelled and analysed by SCAPS-1D simulation program by using the physical parameters of the semiconductor layers that make up solar cells as imputs of program. Photovoltaic parameters of solar cell based on donor defect density, the neutral interface defect density and Auger electron/hole capture coefficient which were calculated by using In %3 doped CdS thin film, which has the most ideal n-type semiconductor properties.

  • Open Access

    SIMULATION STUDIES OF CR DOPED CUO HETEROJUNCTION SOLAR CELL

    by Serap Yi̇ğİt Gezgi̇n, Şilan Baturay, İlHan Candan, Hamdi Şükür Kiliç

    1% and 3% Cr doped CuO thin films have been deposited on soda lime glass by spin coating method and then their structural, morphological and optical properties have been investigated by operating X-Ray Diffraction (XRD), Scanning Electron Microscopy (SEM) and Ultraviolet-Visible Spectroscopy (UV-Vis) techniques, respectively. XRD patterns of CuO:Cr (1%) and CuO:Cr (3%) thin films demonstrate characteristics of monoclinic CuO structure with a C2/c space group. The morphology of coated film plays an important role in analyzing some optoelectronic properties. 1% Cr doped CuO thin film absorbs more photons compared to 3% Cr doped CuO in Vis and UV regions. The band gaps of 1% Cr and 3% Cr doped CuO thin films are to be 2.18 eV and 2.30 eV, respectively. The Mo/1% and 3% Cr doped CuO/n-ZnO/i-ZnO/AZO solar cell has modelled with SCAPS-1D simulation program. The photovoltaic (PV) parameters of solar cell deteriorated with some increase in the neutral defect density (N_t) value. As the shallow acceptor defect density (N_a) value is increased, J_SC is decreased, V_OC, FF and η are increased. PV performance of 1% Cr doped CuO solar cell were found to be better than that of 3% Cr doped CuO solar cell. The efficiency of 1% Cr doped CuO solar cell is increased with the use of SnO2 intermediate layer in 2 nm thickness at the heterojunction interface.


  • Optical and Morphological Properties of Cu2FeSnS4 Chalcogenide Films

    by Canan Aytuğ Ava, Şilan Baturay

    P-type Cu2FeSnS4 (CFTS) and Cu2ZnSnS4 (CZTS) quaternary chalcogenide films have been grown by the method of spin coating on glass substrates relate to 30 and 40 sccm sulfur flux. Physical properties of obtained samples were investigated by X-ray diffraction (XRD), scanning electron microscopy (SEM), atomic force microscopy (AFM) and ultraviolet visible spectroscopy (UV-Vis) to see the effect of deposition parameters on the thin film. The crystal parameters including crystal size, dislocation density and strain value of the samples were changed related to the deposition parameters. XRD results indicated an improvement of the crystalline quality of quaternary chalcogenide CFTS with a maximum crystal size of about 50 nm for (112) peak orientation. SEM images illustrated that the particle size was changed with an increase in the flux of sulfur, which was confirmed with both XRD and AFM images. It was seen that the absorption and energy band gap value of the samples changed the effect of sulfur flux and CZTS film for 40 sccm exhibited more strong absorption all samples in the UV-Vis region. The band gap values of the samples were calculated 1.51, 1.53, 1.82 and 1.91 eV for CZTS (30 sccm), CZTS (40 sccm), CFTS (30 sccm) and CFTS (40 sccm) films annealed H2S gas, respectively.

  • Influence of Mn doping on electrical properties of TiO 2 /Si heterojunction diode

    by Silan Baturay, Omer Bicer, Serap Yigit Gezgin, Ilhan Candan, Hadice Budak Gumgum, Hamdi Sukur Kilic

    In this special work, two types of material, which are undoped and Mn doped TiO 2 thin films, have been produced by spin coating technique, and then their structural, morphological and optical properties have been measured at different Mn doping rates. Four different doping ratios, undoped, 1, 3 and 5% Mn doped TiO 2 have been both experimentally and theoretically investigated and some significant enhancements have been reported. The results of X-ray diffraction (XRD) such as dislocation density, strain, and crystallite size have indicated that undoped, 1, 3 and 5% Mn doped TiO 2 thin films had the phase of anatase at 450 °C. It has been observed that the peak intensity of 3% Mn doped TiO 2 films has decreased compared to undoped and 1% Mn doped TiO 2 while the peak intensity has increased for 5% Mn doped TiO 2 . The refractive indices and dielectric coefficients of the undoped and Mn doped TiO 2 thin films have also been calculated. The undoped and Mn doped TiO 2 /p-Si heterojunction diodes has exhibited photosensitive behaviour in the illuminated environment. 1% Mn doped TiO 2 /p-Si heterojunction diode indicated the highest photocurrent. The electrical parameters of all diodes have been calculated and compared to the conventional J – V and Norde methods. Additionally, 1% Mn doped TiO 2 /p-Si heterojunction diode has been modelled by using the SCAPS-1D program, and J ph values have also been calculated based on the shallow donor density ( N D ). The experimental and theoretical J ph values of this diode were found to be compatible with each other.


  • Open Access

    Al Doping Influence on Structural, Morphological and Optical Properties of CuO Films

    by Şilan Baturay, Canan Aytuğ Ava

    In this study, CuO nanostructured films conjunction with metal doping have been deposited onto soda lime glass (SLG) substrate by method of spin coating at different doping concentration in solution (0%, 2% and 4%). X-ray diffraction (XRD) patterns for copper oxide films conjunction with Al doping demonstrated that the films have polycrystalline structure and have preferential growth in (-111) and (200) directions. Calculated dislocation density value of (-111) plane is changed between 3.7 x 1014 and 5.83 x 1014 m-2 and 83.7 x 1014 and 50.6 x 1014 m-2 for (200) owing to the expansion of structural parameters with Al dopant content in solution. In order to investigate surface morphology, we used an atomic force microscopy (AFM). The obtained results from AFM revealed that samples are comparatively smooth in the valley area while many crystals-like structures are seen in the hill area. In order to examine absorbance, energy band gap and transmittance value of Al doped CuO films, we used a UV-Vis measurements system in the range of 1100-300 nm at temperature of 273 K. The obtained samples have high absorption in the region of UV-Vis and have a high affinity for UV light. It can be said that the change in the absorption value is a result of the different crystal nature of the samples. Energy band gap value of Al:CuO thin films changed between 1.98 and 2.07 eV.

  • Open Access

    A one-dimensional modeling tool for solar cells called SCAPS on CZTS/ZnS

    by Serap Yigit Gezgin, Silan Baturay, Hamdi Sukur Kilic

    In the study, Zinc sulphide thin films were deposited related to different annealing ambient by ultrasonic spray pyrolysis technique (USP) on soda lime glass substrates. Optical properties of these films were analyzed by using ultraviolet–visible (UV–Vis) spectrophotometry at room temperature. Ultraviolet– visible spectroscopy measurements indicate that all ZnS thin films indicated high extinction coefficient in the NIR region. ZnS thin films, which was un annealed and annealed at N2 atmosphere show higher skin depth in the low and high energy bands. However, the skin depth of ZnS thin film annealed at 500 OC at H2S:Ar (1:10) is the lowest compared to the other thin films. Au/CZTS/ZnS-500&ZnS-550/i-ZnO/AZO solar cells that is modelled by SCAPS simulation. The increase of the shallow donor defect density (ND) and Auger electron/hole capture coefficient that deteriorated photovoltaic performance. After Auger electron/hole capture coefficient=10-24 cm6 /s, there are recombined that more electrons from the charge carriers formed in ZnS thin film annealed at 500 OC at H2S:Ar. SnO2 intermediate layer, is placed between CZTS and ZnS layers, caused more charge separation at the two interfaces and increased V oc and efficiency of the solar cell.

  • Open Access

    CZTS/ZnS solar cell modelled with SCAPS-1D simulation program

    by Serap Yigit Gezgin, Silan Baturay, Hamdi Sukur Kilic

    In the study, zinc sulphide (ZnS) thin films compound of the II–VI group were fabricated by known as ultrasonic spray pyrolysis technique (USP) on glass substrates. Optical properties of these films were characterized by using ultraviolet–visible (UV–Vis) spectrophotometry. Measurements of Ultraviolet–visible spectroscopy point out that the absorbance and direct band gap of zinc sulphide samples annealed at diverse ambient is improved. Energy band gap of the obtained ZnS thin film found to be 3.75, 3.66, 3.58, 3.68 and 3.70 eV for ZnS-as grown, ZnS-N2, ZnS-air, ZnS-H2S 500, ZnS-H2S 550 films, respectively. ZnS thin film, which is annealed H2S:Ar ambient at 550 C, has higher absorption and extinction coefficient compared to other thin films. Refractive indices were calculated with Moss and Herve&Vardamme relations. ZnS thin film, which is annealed at air ambient has the highest refractive index, ZnS thin film, which is not annealed has the lowest one. Au/CZTS/ZnS-500&ZnS-550/i-ZnO/AZO solar cells that is modelled by SCAPS simulation. ND value from 2.1016 to 1.1017 cm-3 , VOC, JSC and n values, which decreased from 0.711 V to 0.576 V, from 15.44 mAcm-2 to 10.78 mAcm-2 , from 7.48% to 4.47%, respectively. SnO2 intermediate layer, is placed between CZTS and ZnS layers, caused more charge separation at the two interfaces and increased VOC and efficiency of the solar cell.