Yixuan Guo
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
Yixuan Guo has a total of 21 co-authors. Here are the top co-authors by number of shared publications:
- Chenglong Fu
Southern University of Science and Technology
2 shared publications Hongqiang Zhang
2 shared publicationsJun Cheng
2 shared publicationsYuanyuan Li
2 shared publications- Yuquan Leng
Harbin Institute of Technology (Shenzhen)
2 shared publications Zhen Zeng
2 shared publications
Latest Publications
- 9 November 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 268-273
Leg Transmission Mechanism for Enhanced Load-Carrying Capacity: Knee Joint Torque Optimization Design
This study proposes an optimized design for the leg transmission structure of a quadruped robot, aiming to enhance the load-bearing capacity of the knee joint. Firstly, the dynamic simulation of the single leg's load-lifting process in the quadruped robot is conducted, indicating higher torque demands on the knee joint during this process. Therefore, a leg transmission mechanism, combining a ball screw mechanism and a crank-slider mechanism, is designed to effectively amplify the torque of the knee joint motor. Subsequently, a virtual prototype of the quadruped robot, incorporating this design, is constructed using Adams software. The foot trajectory of the robot is pre-planned, and the joint trajectories are obtained through inverse kinematics, using them as the driving functions for the quadruped robot to perform actions such as load lifting, static standing, and diagonal walking gait. Finally, the knee joint torque and corresponding motor driving torque of the quadruped robot's legs are measured and compared. The results demonstrate that the driving torque of the knee joint motor is effectively amplified by the leg transmission mechanism, with the maximum amplification observed during the initial stage of load lifting, reaching a magnification factor of nearly 7.66 times. This verifies the effectiveness of the proposed leg transmission mechanism in enhancing the load-bearing capacity of the knee joint.
- 9 November 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 268-273
Leg Transmission Mechanism for Enhanced Load-Carrying Capacity: Knee Joint Torque Optimization Design
This study proposes an optimized design for the leg transmission structure of a quadruped robot, aiming to enhance the load-bearing capacity of the knee joint. Firstly, the dynamic simulation of the single leg's load-lifting process in the quadruped robot is conducted, indicating higher torque demands on the knee joint during this process. Therefore, a leg transmission mechanism, combining a ball screw mechanism and a crank-slider mechanism, is designed to effectively amplify the torque of the knee joint motor. Subsequently, a virtual prototype of the quadruped robot, incorporating this design, is constructed using Adams software. The foot trajectory of the robot is pre-planned, and the joint trajectories are obtained through inverse kinematics, using them as the driving functions for the quadruped robot to perform actions such as load lifting, static standing, and diagonal walking gait. Finally, the knee joint torque and corresponding motor driving torque of the quadruped robot's legs are measured and compared. The results demonstrate that the driving torque of the knee joint motor is effectively amplified by the leg transmission mechanism, with the maximum amplification observed during the initial stage of load lifting, reaching a magnification factor of nearly 7.66 times. This verifies the effectiveness of the proposed leg transmission mechanism in enhancing the load-bearing capacity of the knee joint.
- 9 November 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 55-60
Environmental Recognition and Multimode Continuous-Phase Control for a Powered Transfemoral Prosthesis
The continuous-phase-based control method is currently being developed for powered transfemoral prostheses. However, most of the research concentrates on single locomotion mode. The multimode continuous-phase control method for powered transfemoral prostheses is still an open question. To solve the existing problem, this paper proposes a multimode continuous-phase control method for powered transfemoral prostheses. The prosthesis first needs to recognize the surrounding environment and obtain the corresponding environmental features. Then, the gait phase is estimated by phase variable which represents the mapping relationship between thigh angle and gait phase. Finally, the desired trajectories of the knee and ankle joints on various locomotion modes are constructed as functions of the gait phase and environmental features. These functions are called virtual constraints. The proposed phase variable and virtual constraints are evaluated on a public dataset through offline analysis. The root mean squared errors (RMSEs) of the phase variable and virtual constraints in all locomotion modes are less than 3 % and 4 %, respectively. It proves that the proposed method can precisely predict the gait phase and joints angle for powered prostheses in all locomotion modes.
- 9 November 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 55-60
Environmental Recognition and Multimode Continuous-Phase Control for a Powered Transfemoral Prosthesis
The continuous-phase-based control method is currently being developed for powered transfemoral prostheses. However, most of the research concentrates on single locomotion mode. The multimode continuous-phase control method for powered transfemoral prostheses is still an open question. To solve the existing problem, this paper proposes a multimode continuous-phase control method for powered transfemoral prostheses. The prosthesis first needs to recognize the surrounding environment and obtain the corresponding environmental features. Then, the gait phase is estimated by phase variable which represents the mapping relationship between thigh angle and gait phase. Finally, the desired trajectories of the knee and ankle joints on various locomotion modes are constructed as functions of the gait phase and environmental features. These functions are called virtual constraints. The proposed phase variable and virtual constraints are evaluated on a public dataset through offline analysis. The root mean squared errors (RMSEs) of the phase variable and virtual constraints in all locomotion modes are less than 3 % and 4 %, respectively. It proves that the proposed method can precisely predict the gait phase and joints angle for powered prostheses in all locomotion modes.
- 24 February 2022
- Published by American Chemical Society (ACS) in ACS Applied Energy Materials
- Vol. 5 (3) , 2853-2861
Li2CO3: Insights into Its Blocking Effect on Li-Ion Transfer in Garnet Composite Electrolytes
- 24 February 2022
- Published by American Chemical Society (ACS) in ACS Applied Energy Materials
- Vol. 5 (3) , 2853-2861
Li2CO3: Insights into Its Blocking Effect on Li-Ion Transfer in Garnet Composite Electrolytes