WGWenlan Gong

Wenlan Gong

*This is an algorithmically generated author record based on publicly available information.

Wenlan Gong has a total of 38 co-authors. Here are the top co-authors by number of shared publications:

  • Yuhong Mo

    Southern Power Grid Corporation, Electric Power Research Institute of Guangxi Power Grid Co., Ltd,Wireless Power Transmission Joint Laboratory,Nanning,China

    17 shared publications
  • Jing Xiao

    Electric Power Research Institute of Guangxi Power Grid Co.,Ltd,Southern Power Grid Corporation Wireless Power Transmission Joint Laboratory,Nanning,China

    10 shared publications
  • Ning Wu

    College of Communication Engineering, Jilin University, Changchun, China

    9 shared publications
  • Jing Xiao

    Southern Power Grid Corporation Wireless Power Transmission Joint Laboratory Chongqing University Chongqing, Nanning, Guangxi, China

    8 shared publications
  • Xiaorui Wu

    Electric Power Research Institute of Guangxi Power Grid Co., Ltd,Southern Power Grid Corporation Wireless Power Transmission Joint Laboratory,Nanning,China

    8 shared publications
  • Xiaorui Wu

    Electric Power Research Institute of Guangxi Power Grid Co.,Ltd,Southern Power Grid Corporation Wireless Power Transmission Joint Laboratory,Nanning,China

    8 shared publications

Latest Publications

  • Review on Foreign Body Detection Technology of Electric Vehicle Wireless Charging System

    by Ning Wu, Hongbo Jian, Jing Xiao, Xiaorui Wu, Wenlan Gong, Yuhong Mo

    Foreign body detection technology is directly related to the safety of wireless charging systems. Therefore, this essay analyzes the domestic and international research status of foreign body detection technology of radio energy transmission system in the field of electric vehicles, analyzes and explains the advantages and disadvantages of various methods, and prospects the future development trend.

  • Modeling and simulation of energy signal co-transmission in multi-receiver MC-WPT system

    by Xiliu Liu, Tao Shen, Feng Meng, Wenlan Gong, Yuhong Mo, Ning Wu

    With the development of wireless power transfer (WPT) technology, the system consisting of a single transmitter and receiver can no longer meet practical demands. In order to enhance the spatial freedom of energy transmission, a WPT system with multiple receivers has been proposed. Considering that each receiver has different sizes, positions, orientations, load characteristics, and power requirements, there is a need for fast and reliable information exchange between the primary and secondary sides. The technology of energy signal sharing channel enables the electrical energy transmission channel and the information transmission channel to be independent in the frequency domain, with minimal impact of information transmission on energy transmission, thus becoming an important means of communication in multi-coil wireless power transfer (MC-WPT) systems. Based on this, this paper analyzes the energy transmission channel and signal transmission channel of a WPT system with multiple receivers, which share an energy signal sharing channel. A notch filter network is designed to mitigate the interference between channels. After establishing the system model, suitable parameters are selected, and a simulation model is built in Simulink. The effectiveness of this approach is verified through simulation.

  • Order Reduction for Dynamic Modeling of WPT Systems with Phase Shift Control

    by Kai Xing, Jing Xiao, Yuhong Mo, Wenlan Gong, Xiaorui Wu

    In the modeling of wireless power transfer systems, traditional modeling approaches often result in high-order models. In order to obtain a simplified model that can explain the input-output relationship of the system, this paper focuses on the LCC-LCC resonant compensating wireless power transfer system and proposes a method for establishing a dynamic model based on phase control. The model is then reduced to a first-order model using Taylor series expansion. Through comparison, it is found that the accuracy of this first-order model is not significantly compromised.


  • Design of WPT-HW Protocol Frequency Switching Reliable Simultaneous Interpreting System Based on LCC-S Network

    by Wenlan Gong, Yan Wang, Jing Xiao, Shaonan Chen, Xiaorui Wu, Yuhong Mo

    The synchronous transmission of wireless power and signal is one of the research hotspots in wireless power transfer (WPT) technology. This article analyzes the resonant frequency design method of LCC-S compensation network and proposes a design method for high, low frequency, and frequency switching of signal transfer. Designed a signal modulation and demodulation scheme based on frequency switching, and established a Matlab simulation system. Combined with WPT-HW protocol, the system is simulated to verify the validity of (Wireless Power Transfer with Harmonic Wireless Communication) the system to achieve reliable simultaneous interpreting and the correctness of optimizing the system performance through the protocol.

  • High Misalignment Tolerance and Constant Voltage Output WPT System Based on DSFS-DD Pads

    by Yuhong Mo, Xiaorui Wu, Yingjie Li, Wenlan Gong, Jing Xiao, Ning Wu

    Compared with traditional contact wired power transfer technology, Wireless Power Transfer Technology (WPT) has the advantages of high security, flexibility, and reliability. However, in the process of static wireless power transfer in electric vehicles, the inaccuracy of manual parking can lead to the positional deviation between the transmitter and receiver, resulting in reduced power and efficiency of the system's power transfer, as well as system detuning and other issues. Therefore, it is expected that wireless power transfer systems can have a greater tolerance for position misalignment. Therefore, a new coupling machine with high misalignment tolerance is proposed in this article. The transmitter of this coupling mechanism consists of two double forward series flat solenoid coils(DSFS), and the receiver consists of a set of double D(DD) coils. Compared with traditional square and double D coils, the proposed new coupling mechanism improves misalignment tolerance in the x and y directions. This article first analyzes the characteristics and magnetic field distribution characteristics of the DSFS-DD coupling mechanism. Then, based on the constant voltage wireless power characteristics of electric vehicles, an LCC-S compensation network with constant voltage output characteristics was selected. Based on this, expressions for system output voltage, transfer efficiency, and output power are derived. To achieve stable system output voltage and power in the case of misalignment of the coupling mechanism, the coupling mechanism parameters were designed. Finally, simulation experiments are established to verify the effectiveness of the proposed method.


  • Power Fluctuation Suppression Method for WPT System Based on Additional Coupling Channels

    by Wenjie Yuan, Wenlan Gong, Jing Xiao, Yuhong Mo, Xiaorui Wu, Chunsen Tang

    At present, research on the suppression of power fluctuations in wireless charging systems mainly focuses on addressing lateral (X) and longitudinal (Y) offsets, while there is relatively little research on vertical (Z) offsets. This article proposes a new method to suppress power fluctuations in the wireless charging system of electric vehicles by using additional coupling channels to achieve closed-loop control. A rectangular coil mutual inductance calculation model has been established, accurately describing the relationship between two sets of coils. The higher-order components of the secondary side output are fed back to the primary side through additional coupling channels, and mutual inductance estimation and output calculation are achieved only at the power transmission end. On the basis of circuit analysis, the optimization design process of feedback loop is provided. Replacing the communication of closed-loop control with additional coupling channels, converting digital signals into analog signals, eliminating the stages of communication and data processing, and improving the real-time performance of the system.

  • Analysis and Design of a Metal Object Detection Method for Wireless Power Transfer Systems

    by Xiaorui Wu, Yuhong Mo, Jingyue Wang, Shaonan Chen, Jing Xiao, Wenlan Gong

    There will be eddy current effect while foreign bodies inevitably enter the gap between the transmitting coil and the receiving coil in the process of magnetic field induction radio energy transmission, which could lead to the high temperature and inefficiency of the system or even significant security risks. In this paper, a detection method of metal foreign bodies in the auxiliary coil perpendicular to the energy coil is designed. The magnetic coupling mechanism model based on MAXWELL software was built to obtain parameters of the magnetic coupling mechanism by simulation. On this basis, the Simulink circuit simulation model of radio energy transmission system is established, and its energy transmission characteristics are analyzed. Based on the designed radio energy transmission system, a detection coil perpendicular to the energy coil was designed, and its MAXWELL 3D simulation model was established to obtain its coupling characteristics. The experimental prototype is built and the metal foreign body detection experiment is conducted. The results of experiment are consistent with that of the simulation, which verifies that the vertical detection coil proposed in this paper is a feasible method for the detection of metal foreign bodies in the radio energy transmission system.


  • A Wide Range ZVS Implementation Method for MCWPT Systems Based on Self-Inductance Variation

    by Yahui Jia, Jing Xiao, Wenlan Gong, Xiaorui Wu, Yuhong Mo

    In wireless power transfer (WPT) systems, changes in air gaps are inevitable, which can cause drift of mutual inductance and self-inductance parameters, leading to a decrease in output power and efficiency. In this paper, a wide coupling range zero voltage switching (ZVS) implementation method with phase shift control (PSC) is proposed, which improves the system efficiency while achieving constant voltage (CV) output characteristics. Based on the time domain model analysis of the inductor–capacitor–capacitor-series (LCC-S) topology, the influence law of coil self-inductance variation on the implementation of ZVS is obtained. The magnetic coupler was designed and the parameters were optimized to realize the ZVS operation with the range of air gap variation of 10~60mm, mutual inductance variation of 21~85μH, maximum self-inductance variation of 80.5~139μH, coupling coefficient variation of 0.2~0.6, and minimum reactive current.


  • Parameter Design Method for Series-series Compensated Wireless Power Transfer System Based on Natural Frequency Tracking

    by Yuhong Mo, Jing Xiao, Xiaorui Wu, Wenlan Gong, Ning Wu

    This article proposes a parameter design method based on natural frequency configuration, which enables the system to achieve approximately constant voltage output characteristics independent of load under the expected frequency operating conditions. Firstly, the natural frequency calculation method of the system was obtained by solving the eigenvalues of the second-order time-domain model of the system. Subsequently, a parameter configuration constraint equation was established for the parameter design method, and the approximate constant voltage output of the system at the expected operating frequency was obtained. And the constant voltage characteristic of the system at the designed frequency was verified by theoretically calculating the voltage gain expression of the system. Finally, the correctness of this method was verified through circuit simulation.

  • Analysis of Wireless Communication System Based on Magnetic Field Coupling

    by Yuhong Mo, Yun Wen, Jing Xiao, Xiaorui Wu, Shaonan Chen, Wenlan Gong

    This paper mainly studies the magnetic induction wireless communication system based on electric vehicle wireless charging system in different environments. In this paper, the common signal modulation and demodulation methods are analyzed, and the binary digital amplitude modulation is selected as the signal modulation method of the experimental system. The basic structure of the magnetic coupling communication system for electric vehicles is designed and built. The influence of coil placement position and different dielectric conductivity on the bit error rate of the communication system under the same noise signal-to-noise ratio is studied and analyzed. The system communication performance, channel resonance circuit design and different modulation methods are compared and analyzed.