Daniel Franz
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Daniel Franz has a total of 23 co-authors. Here are the top co-authors by number of shared publications:
- Cemal Esen
Applied Laser Technologies, Ruhr University Bochum, Bochum, Germany
9 shared publications - Yongting Yang
Applied Laser and Photonics Group, University of Applied Sciences Aschaffenburg 1 , Würzburger Straße 45, 63743 Aschaffenburg
8 shared publications - Ralf Hellmann
Applied Laser and Photonics Group, University of Applied Sciences Aschaffenburg, Aschaffenburg, Germany
7 shared publications Ralf Hellmann
Applied Laser and Photonics Group, University of Applied Sciences Aschaffenburg 1 , Würzburger Straße 45, 63743 Aschaffenburg
5 shared publicationsCemal Esen
Applied Laser Technologies, Ruhr University Bochum 2 , Universitätsstraße 150, Bochum 44801, Germany
3 shared publicationsStefan Rung
Schmoll Maschinen GmbH, Odenwaldstraße 67, 63322 Rödermark, Germany
2 shared publications
Latest Publications
- 1 November 2026
- Published by Laser Institute of America in Journal of Laser Applications
- Vol. 38 (4)
2D to 3D percussion drilling of thin metal foils using a fiber-based ultrashort pulsed laser robotic system
We report on 2D and 3D percussion drilling of thin metal foils using a six-axis articulated laser robot with flexible beam guidance of ultrashort laser pulses via a hollow-core fiber (HCF). Prior to drilling experiments, single-pulse ablations are conducted at different robot coordinates of thin transparent oxide layers to analyze the influence of HCF bending on beam characteristics and the resulting ablation pattern. In these experiments, we find a hexagonal ablation geometry of various sizes and different shape characteristics. To optimize the drilling quality in copper, brass, and mild steel foils, as being evaluated by the inlet and outlet diameters and the taper angle using laser scanning microscopy, a different number of pulses is applied in single-pulse and MHz burst modes. Our results show a material-dependent taper behavior due to different optical and thermophysical properties and dynamic in-hole processes. Furthermore, drilling brass and copper foils with two burst pulses in the MHz burst mode results in an average taper angle reduction of up to 31.5 %, which is mainly attributed to smaller inlet diameters and increasing heat accumulation inside the boreholes. 3D percussion drilling is performed on brass foils perpendicular to the workpiece surface within a large spatial area of 800 × 600 × 200 mm and workpiece inclinations ranging from −15° to 15° in the x- and y-directions. Experiments reveal a high consistency in the fabricated inlet and outlet diameters and tapers with small fluctuations, highlighting the potential of our novel laser robot for flexible 3D micromachining.
- 1 November 2026
- Published by Laser Institute of America in Journal of Laser Applications
- Vol. 38 (4)
2D to 3D percussion drilling of thin metal foils using a fiber-based ultrashort pulsed laser robotic system
We report on 2D and 3D percussion drilling of thin metal foils using a six-axis articulated laser robot with flexible beam guidance of ultrashort laser pulses via a hollow-core fiber (HCF). Prior to drilling experiments, single-pulse ablations are conducted at different robot coordinates of thin transparent oxide layers to analyze the influence of HCF bending on beam characteristics and the resulting ablation pattern. In these experiments, we find a hexagonal ablation geometry of various sizes and different shape characteristics. To optimize the drilling quality in copper, brass, and mild steel foils, as being evaluated by the inlet and outlet diameters and the taper angle using laser scanning microscopy, a different number of pulses is applied in single-pulse and MHz burst modes. Our results show a material-dependent taper behavior due to different optical and thermophysical properties and dynamic in-hole processes. Furthermore, drilling brass and copper foils with two burst pulses in the MHz burst mode results in an average taper angle reduction of up to 31.5 %, which is mainly attributed to smaller inlet diameters and increasing heat accumulation inside the boreholes. 3D percussion drilling is performed on brass foils perpendicular to the workpiece surface within a large spatial area of 800 × 600 × 200 mm and workpiece inclinations ranging from −15° to 15° in the x- and y-directions. Experiments reveal a high consistency in the fabricated inlet and outlet diameters and tapers with small fluctuations, highlighting the potential of our novel laser robot for flexible 3D micromachining.
- Open Access
- 30 October 2026
- Published by MDPI AG in Applied Sciences
- Vol. 16 (21) , 10745
Structure Depth Monitoring During Processing of Multi-Layer Materials with a Fiber-Based Ultrashort Pulsed Laser Robot
We report on the laser structuring of multi-layer materials using a fiber-based ultrashort pulsed laser robotic system within a processing area of 800 mm × 600 mm × 200 mm. Structuring was performed on a CuAl foil consisting of copper and aluminium layers, as well as on a two-layer printed circuit board (PCB) material comprising two copper layers separated by a polyimide layer. Experiments at different robot coordinates revealed structure depth deviations of up to 9.5 µm for applying a constant number of laser passes. To improve the accuracy and repeatability of the structure depth for true 3D applications, an inline monitoring method based on laser-induced breakdown spectroscopy (LIBS) was introduced. The method enables the real-time detection of material transitions during each single laser structuring pass by analyzing the optical emission intensities at characteristic wavelengths of the individual layer materials. The process is stopped when the ratio of the LIBS intensities of adjacent material layers falls below a predefined threshold. Laser structuring experiments with the LIBS-based process monitoring showed a reduction in the maximum structure depth deviations down to 2.9 µm and 1.9 µm for the CuAl composite foil and the two-layer PCB material, respectively. These results demonstrate the potential of the LIBS-based monitoring approach for achieving precise structure depth control, the removal of material layers and the minimization of damage to the underlying target layers during the processing of multi-layer materials.
- 30 October 2026
- Published by MDPI AG in Applied Sciences
- Vol. 16 (21) , 10745
Open AccessStructure Depth Monitoring During Processing of Multi-Layer Materials with a Fiber-Based Ultrashort Pulsed Laser Robot
We report on the laser structuring of multi-layer materials using a fiber-based ultrashort pulsed laser robotic system within a processing area of 800 mm × 600 mm × 200 mm. Structuring was performed on a CuAl foil consisting of copper and aluminium layers, as well as on a two-layer printed circuit board (PCB) material comprising two copper layers separated by a polyimide layer. Experiments at different robot coordinates revealed structure depth deviations of up to 9.5 µm for applying a constant number of laser passes. To improve the accuracy and repeatability of the structure depth for true 3D applications, an inline monitoring method based on laser-induced breakdown spectroscopy (LIBS) was introduced. The method enables the real-time detection of material transitions during each single laser structuring pass by analyzing the optical emission intensities at characteristic wavelengths of the individual layer materials. The process is stopped when the ratio of the LIBS intensities of adjacent material layers falls below a predefined threshold. Laser structuring experiments with the LIBS-based process monitoring showed a reduction in the maximum structure depth deviations down to 2.9 µm and 1.9 µm for the CuAl composite foil and the two-layer PCB material, respectively. These results demonstrate the potential of the LIBS-based monitoring approach for achieving precise structure depth control, the removal of material layers and the minimization of damage to the underlying target layers during the processing of multi-layer materials.
- 22 September 2026
- Published by Laser Institute of America in Journal of Laser Applications
- Vol. 38 (4)
Straightness deviation detection during ultrashort-pulsed laser robot cutting using machine learning and deep learning
The authors report artificial intelligence-based methods for detecting cutting straightness deviations in the flexible ultrathin glass cutting process using an ultrashort-pulsed laser robotic system. In this system, an ultrashort-pulsed laser is integrated onto the link behind the elbow of a six-axis articulated industrial robot. The laser beam is guided by a mirrors and propagates along subsequent robot axes, enabling precision laser processing over a large and flexible working area. System vibration is a critical factor affecting process quality and consistency. To monitor this dynamic behavior of the laser robot system during the cutting process, a triaxial accelerometer is mounted on the final robot link. The acquired vibration signals are applied to train machine learning and deep learning models to detect cutting straightness deviations. Random Forest, eXtreme Gradient Boosting, Light Gradient Boosting Machine, and Linear Discriminant Analysis, a lightweight 1D-convolutional neural network (CNN) model, a 1D-CNN autoencoder, and a transformer model are evaluated. Comparing time-domain and frequency-domain datasets, the lightweight 1D-CNN model trained on the frequency-domain vibration dataset achieves the best performance in detecting both normal and abnormal vibrations during the cutting process, with an AUC (area under the curve) of 0.93 and an F1-score of 0.844, demonstrating its capability to detect cutting straightness deviations in glass cutting processes using the ultrashort-pulsed laser robot system.
- 22 September 2026
- Published by Laser Institute of America in Journal of Laser Applications
- Vol. 38 (4)
Straightness deviation detection during ultrashort-pulsed laser robot cutting using machine learning and deep learning
The authors report artificial intelligence-based methods for detecting cutting straightness deviations in the flexible ultrathin glass cutting process using an ultrashort-pulsed laser robotic system. In this system, an ultrashort-pulsed laser is integrated onto the link behind the elbow of a six-axis articulated industrial robot. The laser beam is guided by a mirrors and propagates along subsequent robot axes, enabling precision laser processing over a large and flexible working area. System vibration is a critical factor affecting process quality and consistency. To monitor this dynamic behavior of the laser robot system during the cutting process, a triaxial accelerometer is mounted on the final robot link. The acquired vibration signals are applied to train machine learning and deep learning models to detect cutting straightness deviations. Random Forest, eXtreme Gradient Boosting, Light Gradient Boosting Machine, and Linear Discriminant Analysis, a lightweight 1D-convolutional neural network (CNN) model, a 1D-CNN autoencoder, and a transformer model are evaluated. Comparing time-domain and frequency-domain datasets, the lightweight 1D-CNN model trained on the frequency-domain vibration dataset achieves the best performance in detecting both normal and abnormal vibrations during the cutting process, with an AUC (area under the curve) of 0.93 and an F1-score of 0.844, demonstrating its capability to detect cutting straightness deviations in glass cutting processes using the ultrashort-pulsed laser robot system.
- Open Access
- 30 July 2026
- Published by MDPI AG in Applied Sciences
- Vol. 16 (15) , 7565
Evaluation of Ultra-Thin Glass Cutting Edges Using an Ultrashort Pulsed-Laser Robot System
We report on an evaluation of cutting edge ultra-thin glass processed by a novel ultrashort pulsed-laser robot system. The system consists of a six-axis articulated industrial robot with an ultrashort pulsed laser integrated on the link after the robot’s elbow. Mirrors are used for beam aligning and guiding, and a 2D galvanometer scanner and an F-Theta lens mounted on the last robot axis are used for material processing. Ultra-thin glass AF 32 eco is cut using robot motion only and combined scanner–robot motion, with additional axis rotations about the laser beam focusing in two directions. Hybrid cutting is compatible with a wide range of rotation angles, achieving cutting-edge angles from 88.9° to 119.7°. The influence of cutting-edge angles and cutting methods is further evaluated using residual stress measurements and three-point bending tests, revealing that the cutting method has a dominant impact on cutting-edge quality. To demonstrate the large-scale cutting with defining cutting-edge angles, a trapezoid is cut using the hybrid method with extra robot axis rotation, which achieves an average cutting-edge angle of 91.9°.
- 30 July 2026
- Published by MDPI AG in Applied Sciences
- Vol. 16 (15) , 7565
Open AccessEvaluation of Ultra-Thin Glass Cutting Edges Using an Ultrashort Pulsed-Laser Robot System
We report on an evaluation of cutting edge ultra-thin glass processed by a novel ultrashort pulsed-laser robot system. The system consists of a six-axis articulated industrial robot with an ultrashort pulsed laser integrated on the link after the robot’s elbow. Mirrors are used for beam aligning and guiding, and a 2D galvanometer scanner and an F-Theta lens mounted on the last robot axis are used for material processing. Ultra-thin glass AF 32 eco is cut using robot motion only and combined scanner–robot motion, with additional axis rotations about the laser beam focusing in two directions. Hybrid cutting is compatible with a wide range of rotation angles, achieving cutting-edge angles from 88.9° to 119.7°. The influence of cutting-edge angles and cutting methods is further evaluated using residual stress measurements and three-point bending tests, revealing that the cutting method has a dominant impact on cutting-edge quality. To demonstrate the large-scale cutting with defining cutting-edge angles, a trapezoid is cut using the hybrid method with extra robot axis rotation, which achieves an average cutting-edge angle of 91.9°.
- Open Access
- 25 March 2026
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 143 (11-12) , 7241-7253
Novel 6-axis articulated ultrashort pulsed laser robotic system using a hollow-core fiber for flexible micromachining
We report for the first time on the realization, comprehensive characterization and application of a 6-axis articulated laser robot using a flexible beam guidance of ultrashort laser pulses via a non-polarization-maintaining hollow-core fiber. Measurements during and after a movement of the fiber-based ultrashort pulsed laser robotic (USPLR) system reveal that fundamental beam characteristics such as transmission, beam pointing and diameter and pulse duration are only marginally affected after passing through the hollow-core fiber. In addition, we studied the application of the USPLR system to laser cutting of brass foils and a printed circuit board (PCB) substrate in a single-path mode and optimize the process with respect to the heat-affected zone and kerf width by varying the applied pulse energy and robot speed. Our findings reveal that heat accumulation plays a significant role for the cutting quality at slow robot speeds of up to 20 mm/s, whereas a reduction of the kerf width down to about 7 µm is feasible. Furthermore, detected vibrations of the USPLR system with varying magnitude at different 3D spatial cutting positions result in oddness of the cutting edges of up to about 200 µm. Nevertheless, optimized process parameters result in a high cutting quality with a small heat-affected zone and a virtually straight and sharp cutting edges in a large processing area of 500 mm $$\times$$ 600 mm $$\times$$ 300 mm, highlighting the substantial potential of the fiber-based USPLR system for flexible and large-area 2D and 3D micromachining.- 25 March 2026
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 143 (11-12) , 7241-7253
Open AccessNovel 6-axis articulated ultrashort pulsed laser robotic system using a hollow-core fiber for flexible micromachining
We report for the first time on the realization, comprehensive characterization and application of a 6-axis articulated laser robot using a flexible beam guidance of ultrashort laser pulses via a non-polarization-maintaining hollow-core fiber. Measurements during and after a movement of the fiber-based ultrashort pulsed laser robotic (USPLR) system reveal that fundamental beam characteristics such as transmission, beam pointing and diameter and pulse duration are only marginally affected after passing through the hollow-core fiber. In addition, we studied the application of the USPLR system to laser cutting of brass foils and a printed circuit board (PCB) substrate in a single-path mode and optimize the process with respect to the heat-affected zone and kerf width by varying the applied pulse energy and robot speed. Our findings reveal that heat accumulation plays a significant role for the cutting quality at slow robot speeds of up to 20 mm/s, whereas a reduction of the kerf width down to about 7 µm is feasible. Furthermore, detected vibrations of the USPLR system with varying magnitude at different 3D spatial cutting positions result in oddness of the cutting edges of up to about 200 µm. Nevertheless, optimized process parameters result in a high cutting quality with a small heat-affected zone and a virtually straight and sharp cutting edges in a large processing area of 500 mm $$\times$$ 600 mm $$\times$$ 300 mm, highlighting the substantial potential of the fiber-based USPLR system for flexible and large-area 2D and 3D micromachining. - Open Access
- 28 May 2025
- Published by Elsevier in Optics and Lasers in Engineering
- Vol. 193
Fabrication and analysis of through-glass vias for glass-based electronic packaging using an ultrashort pulsed laser
- 28 May 2025
- Published by Elsevier in Optics and Lasers in Engineering
- Vol. 193
Open AccessFabrication and analysis of through-glass vias for glass-based electronic packaging using an ultrashort pulsed laser
- Open Access
- 10 April 2025
- Published by Springer Nature in Journal of Intelligent Manufacturing
- Vol. 37 (3) , 1231-1246
Development of a dynamic beam stabilization system for a six-axis ultrashort pulsed laser robot
We report on the evaluation of a beam stabilization system mounted on a six-axis articulated ultrashort pulsed laser robot system for real 3D micromachining. The system integrates a discrete beam guiding system along the robot links and an optical scanner mounted on the final robot axis, enabling high-speed laser scanning for material processing with high power femtosecond pulses. For true 3D micromachining, the robot positions and orients the scanner, allowing scan fields to be stitched or different workpiece areas to be addressed through robot movement. A cascaded beam stabilization system is developed for beam linear and angular position drift correction. This system is implemented on robot links that extend from the robot axis with an integrated ultrashort pulsed laser to the axis with the scanner. The first stage stabilization stabilizes the beam position drift induced by the movement of the axes preceding the laser-integrated axis, as well as the axis equipped with the laser. The second stage is responsible for stabilizing the beam drift resulting from the following axes. A dynamic beam stabilization algorithm including beam position detection and correction with combining the current robot position is introduced and discussed. The stabilization is applied to correct the beam drift after the robot has reached the desired target position for the following scanner movement. In addition, a neural network prediction model is developed and implemented on the system, which reduces the half correction time and increases the beam drift correction efficiency.
- 10 April 2025
- Published by Springer Nature in Journal of Intelligent Manufacturing
- Vol. 37 (3) , 1231-1246
Open AccessDevelopment of a dynamic beam stabilization system for a six-axis ultrashort pulsed laser robot
We report on the evaluation of a beam stabilization system mounted on a six-axis articulated ultrashort pulsed laser robot system for real 3D micromachining. The system integrates a discrete beam guiding system along the robot links and an optical scanner mounted on the final robot axis, enabling high-speed laser scanning for material processing with high power femtosecond pulses. For true 3D micromachining, the robot positions and orients the scanner, allowing scan fields to be stitched or different workpiece areas to be addressed through robot movement. A cascaded beam stabilization system is developed for beam linear and angular position drift correction. This system is implemented on robot links that extend from the robot axis with an integrated ultrashort pulsed laser to the axis with the scanner. The first stage stabilization stabilizes the beam position drift induced by the movement of the axes preceding the laser-integrated axis, as well as the axis equipped with the laser. The second stage is responsible for stabilizing the beam drift resulting from the following axes. A dynamic beam stabilization algorithm including beam position detection and correction with combining the current robot position is introduced and discussed. The stabilization is applied to correct the beam drift after the robot has reached the desired target position for the following scanner movement. In addition, a neural network prediction model is developed and implemented on the system, which reduces the half correction time and increases the beam drift correction efficiency.
- Open Access
- 30 October 2023
- Published by Laser Institute of America in Journal of Laser Applications
- Vol. 35 (4)
Evaluation of an ultrashort pulsed laser robot system for flexible and large-area micromachining
We report for the first time on the realization, characterization and application of an ultrashort pulsed laser robot system for flexible and large-area 2D and 3D laser micromachining with 6 articulated axes. To characterize the dynamic positioning of the laser beam during and after axes movement, CMOS image sensors were integrated into the beam path. A method introduced for the alignment of the optical axes allows a reduction of the deviations in laser beam positioning to less than 141.8 ± 92.9 μm within a 110° rotation range of axis 4. In addition, a high laser beam positioning repeatability of less than 102.2 μm is demonstrated over a total period of 14 h for a movement of axis 5 within a range of 0° to 90°. Initial laser cutting, laser structuring and laser marking applications on automotive dashboards and glass substrates are presented for flexible and large area 2D and 3D manufacturing. By applying a special laser cutting strategy for processing AF 32 eco thin glass, high cutting quality is achieved with a taper of up to 96.3% without the generation of cracks, demonstrating the innovative potential of the high-precision laser robot system. Nonetheless, different identified inherent influences of each axis 1–5 during robot axis movement demand for an innovative beam stabilization concept to achieve high precision in laser beam positioning.
- 30 October 2023
- Published by Laser Institute of America in Journal of Laser Applications
- Vol. 35 (4)
Open AccessEvaluation of an ultrashort pulsed laser robot system for flexible and large-area micromachining
We report for the first time on the realization, characterization and application of an ultrashort pulsed laser robot system for flexible and large-area 2D and 3D laser micromachining with 6 articulated axes. To characterize the dynamic positioning of the laser beam during and after axes movement, CMOS image sensors were integrated into the beam path. A method introduced for the alignment of the optical axes allows a reduction of the deviations in laser beam positioning to less than 141.8 ± 92.9 μm within a 110° rotation range of axis 4. In addition, a high laser beam positioning repeatability of less than 102.2 μm is demonstrated over a total period of 14 h for a movement of axis 5 within a range of 0° to 90°. Initial laser cutting, laser structuring and laser marking applications on automotive dashboards and glass substrates are presented for flexible and large area 2D and 3D manufacturing. By applying a special laser cutting strategy for processing AF 32 eco thin glass, high cutting quality is achieved with a taper of up to 96.3% without the generation of cracks, demonstrating the innovative potential of the high-precision laser robot system. Nonetheless, different identified inherent influences of each axis 1–5 during robot axis movement demand for an innovative beam stabilization concept to achieve high precision in laser beam positioning.
- Open Access
- 12 October 2023
- Published by Laser Institute of America in Journal of Laser Applications
- Vol. 35 (4)
Development and comparison of algorithms for beam stabilization in ultrashort pulsed laser equipped on a six-axis robot
We demonstrate an innovative beam stabilization concept consisting of complementary metal-oxide semiconductor cameras and piezo actuators for a six-axis articulated ultrashort pulsed laser robot system. The beam stabilization system is fixed on robot axes 4 and 5. Moving robot axis 5 in an angular range between 0° and 90°, the laser beam position coupled to the actual robot position is monitored by two cameras integrated on robot axis 5 and used for laser beam characterization and model generation. A mathematical description and models generated with machine learning methods, namely, linear regression and neural network, are compared for predicting the beam position drift as a function of robot axis motion, where the neural network model shows a low prediction tolerance of about 7 pixels. In addition, a stand-alone time-triggered beam correction algorithm is developed and implemented on the system, which shows an excellent correction performance for large beam position drifts (below 500 pixels).
- 12 October 2023
- Published by Laser Institute of America in Journal of Laser Applications
- Vol. 35 (4)
Open AccessDevelopment and comparison of algorithms for beam stabilization in ultrashort pulsed laser equipped on a six-axis robot
We demonstrate an innovative beam stabilization concept consisting of complementary metal-oxide semiconductor cameras and piezo actuators for a six-axis articulated ultrashort pulsed laser robot system. The beam stabilization system is fixed on robot axes 4 and 5. Moving robot axis 5 in an angular range between 0° and 90°, the laser beam position coupled to the actual robot position is monitored by two cameras integrated on robot axis 5 and used for laser beam characterization and model generation. A mathematical description and models generated with machine learning methods, namely, linear regression and neural network, are compared for predicting the beam position drift as a function of robot axis motion, where the neural network model shows a low prediction tolerance of about 7 pixels. In addition, a stand-alone time-triggered beam correction algorithm is developed and implemented on the system, which shows an excellent correction performance for large beam position drifts (below 500 pixels).
- Open Access
- 1 September 2023
- Published by IOP Publishing in Materials Research Express
- Vol. 10 (9) , 096301
Picosecond laser microvia drilling of ABF material using MHz burst mode
We report on a comprehensive study of laser percussion microvia drilling of Ajinomoto build-up film (ABF) material using an ultrashort pulsed laser in MHz burst mode. After laser processing, microvia drilling quality is being evaluated by the fabricated diameter and taper using laser scanning microscopy and metallography. The influences of the incubation effect, heat accumulation and shielding effects as a result of pulse to pulse interactions are being discussed on the ablation threshold, penetration depth and laser microvia drilling quality. We find that an increasing heat accumulation in MHz burst mode processing is responsible for the void formation and delamination of the insulating ABF layer. Therefore, the parameter clearance is introduced to evaluate these effects on the microvia sidewalls. For a comparable clearance, applying 2 intra-burst pulses achieves an average reduced taper of down to 19.5% compared to single pulse mode. At the same time, a reduced laser drilling time of 16.7% per microvia highlights the enormous potential of the MHz burst mode for laser drilling of ABF material in printed circuit board fabrication.
- 1 September 2023
- Published by IOP Publishing in Materials Research Express
- Vol. 10 (9) , 096301
Open AccessPicosecond laser microvia drilling of ABF material using MHz burst mode
We report on a comprehensive study of laser percussion microvia drilling of Ajinomoto build-up film (ABF) material using an ultrashort pulsed laser in MHz burst mode. After laser processing, microvia drilling quality is being evaluated by the fabricated diameter and taper using laser scanning microscopy and metallography. The influences of the incubation effect, heat accumulation and shielding effects as a result of pulse to pulse interactions are being discussed on the ablation threshold, penetration depth and laser microvia drilling quality. We find that an increasing heat accumulation in MHz burst mode processing is responsible for the void formation and delamination of the insulating ABF layer. Therefore, the parameter clearance is introduced to evaluate these effects on the microvia sidewalls. For a comparable clearance, applying 2 intra-burst pulses achieves an average reduced taper of down to 19.5% compared to single pulse mode. At the same time, a reduced laser drilling time of 16.7% per microvia highlights the enormous potential of the MHz burst mode for laser drilling of ABF material in printed circuit board fabrication.