Satya Venkata Kishore Pulavarthi
Research Subjects
Satya Venkata Kishore Pulavarthi has a total of 21 co-authors. Here are the top co-authors by number of shared publications:
Nakka Jayaram
525574 National Institute of Technology Andhra Pradesh , Tadepalligudam , India
12 shared publications- Jami Rajesh
Department of Electrical and Electronics Engineering , Dayananda Sagar College of Engineering , 560078 , Bengaluru , India
9 shared publications Sukanta Halder
Indian Institute of Technology , Dhanbad , India
5 shared publications- Yannam Ravi Shankar
School of Electrical and Computer Engineering, Dire Dawa University, Dire Dawa, Ethiopia
5 shared publications - Gaurav
Indian Institute of Technology IIT (ISM) Dhanbad
3 shared publications - Sukanta Halder
Sardar Vallabhbhai National Institute of Technology, Surat, India
3 shared publications
Latest Publications
- Open Access
- 5 August 2026
- Published by Springer Nature in Scientific Reports
- Vol. 16 (1)
Design of a novel reliable 9-level switched capacitor-based inverter with low voltage stress on the devices for renewable energy applications
- 5 August 2026
- Published by Springer Nature in Scientific Reports
- Vol. 16 (1)
Open AccessDesign of a novel reliable 9-level switched capacitor-based inverter with low voltage stress on the devices for renewable energy applications
- 10 December 2024
- Published by Walter de Gruyter GmbH in International Journal of Emerging Electric Power Systems
- Vol. 26 (5) , 815-827
A new 9-level quadruple boost inverter for grid integration
This paper presents a novel reduced switch multilevel inverter based on switched capacitor technique for grid integration. It generates nine-level output voltage waveform with only 10 switches. It is suitable for high gain applications since it has a boosting ability of four times. Another feature is that the capacitors have built-in self-voltage balancing. The level shifted pulse width modulation (LSPWM) technique is used to explore the performance of the proposed topology. To determine its optimal performance, the suggested topology is compared to the state-of-the-art topologies in the literature. Simulation of the proposed topology is done under different parameter variations. Further, the thermal design of the proposed topology is done using PLECS software to find the efficiency. Finally, the hardware prototype is implemented using dSPACE 1104 controller to verify its performance.
- 10 December 2024
- Published by Walter de Gruyter GmbH in International Journal of Emerging Electric Power Systems
- Vol. 26 (5) , 815-827
A new 9-level quadruple boost inverter for grid integration
This paper presents a novel reduced switch multilevel inverter based on switched capacitor technique for grid integration. It generates nine-level output voltage waveform with only 10 switches. It is suitable for high gain applications since it has a boosting ability of four times. Another feature is that the capacitors have built-in self-voltage balancing. The level shifted pulse width modulation (LSPWM) technique is used to explore the performance of the proposed topology. To determine its optimal performance, the suggested topology is compared to the state-of-the-art topologies in the literature. Simulation of the proposed topology is done under different parameter variations. Further, the thermal design of the proposed topology is done using PLECS software to find the efficiency. Finally, the hardware prototype is implemented using dSPACE 1104 controller to verify its performance.
- 2 February 2024
- Published by Walter de Gruyter GmbH in International Journal of Emerging Electric Power Systems
- Vol. 26 (2) , 371-382
A new triple voltage gain seven level switched capacitor-based inverter with minimum voltage stress
This paper presents, a new seven level triple voltage gain inverter topology is proposed based on switched capacitor technique. The proposed inverter topology has minimum voltage stresses on the switches and balanced capacitor voltages. This paper briefs the operation of proposed topology, voltage stress analysis, capacitor sizing and generation gate signals for the switches. In addition, proposed topology is modeled in industrial based software PLECS with practical switches to study thermal behavior and efficiency analysis. Further, the proposed inverter topology is compared with competitive topologies in the recent literature. The proposed topology has merits like minimum total standing voltage, switching redundancy and inherent polarity generation. Furthermore, MATLAB based simulations and experimental analysis is done to validate the superior performance the proposed topology. The experimental results for the proposed seven-level inverter are presented and discussed in brief by considering different types of loads, amplitude modulation variations and frequency variations.
- 2 February 2024
- Published by Walter de Gruyter GmbH in International Journal of Emerging Electric Power Systems
- Vol. 26 (2) , 371-382
A new triple voltage gain seven level switched capacitor-based inverter with minimum voltage stress
This paper presents, a new seven level triple voltage gain inverter topology is proposed based on switched capacitor technique. The proposed inverter topology has minimum voltage stresses on the switches and balanced capacitor voltages. This paper briefs the operation of proposed topology, voltage stress analysis, capacitor sizing and generation gate signals for the switches. In addition, proposed topology is modeled in industrial based software PLECS with practical switches to study thermal behavior and efficiency analysis. Further, the proposed inverter topology is compared with competitive topologies in the recent literature. The proposed topology has merits like minimum total standing voltage, switching redundancy and inherent polarity generation. Furthermore, MATLAB based simulations and experimental analysis is done to validate the superior performance the proposed topology. The experimental results for the proposed seven-level inverter are presented and discussed in brief by considering different types of loads, amplitude modulation variations and frequency variations.
- Open Access
- 21 November 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 11, 134023-134039
An Ultra-High Gain Compact Module Bidirectional DC–DC Converter for Energy Storage System
This paper presents a non-isolated bidirectional dc-to-dc converter (BDDC) topology employing a switched inductor switched capacitor (SISC) module. The bidirectional power flow capability aid to its application mainly in microgrids and electric vehicles. The switched inductor (SI) and switched capacitor (SC) cells in combination assist in the generation of high gain voltage without using a bulky transformer. The theoretical analysis of the proposed converter, its gain calculation, and small signal analysis are analyzed in detail. It benefits from having a wide voltage-gain range and less voltage stress across the power switches. Also, the proposed (SISC-BDDC) can operate both in boost and buck modes. Simulations are carried out for both the modes using MATLAB/Simulink platform. A 200 W prototype is also developed to operate with V in = 12 V and V out = 160-200V. Using the dSPACE1104 control platform, the maximum efficiency of 95.25% of the converter is justified in steady and transient operating conditions.
- 21 November 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 11, 134023-134039
Open AccessAn Ultra-High Gain Compact Module Bidirectional DC–DC Converter for Energy Storage System
This paper presents a non-isolated bidirectional dc-to-dc converter (BDDC) topology employing a switched inductor switched capacitor (SISC) module. The bidirectional power flow capability aid to its application mainly in microgrids and electric vehicles. The switched inductor (SI) and switched capacitor (SC) cells in combination assist in the generation of high gain voltage without using a bulky transformer. The theoretical analysis of the proposed converter, its gain calculation, and small signal analysis are analyzed in detail. It benefits from having a wide voltage-gain range and less voltage stress across the power switches. Also, the proposed (SISC-BDDC) can operate both in boost and buck modes. Simulations are carried out for both the modes using MATLAB/Simulink platform. A 200 W prototype is also developed to operate with V in = 12 V and V out = 160-200V. Using the dSPACE1104 control platform, the maximum efficiency of 95.25% of the converter is justified in steady and transient operating conditions.
- Open Access
- 22 March 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 11, 30442-30458
Quadruple Boost Switched Capacitor-Based Inverter for Standalone Applications
Conventional energy sources will not be sufficient to meet future electrical demands, and also pollute the environment. Therefore, to meet their electrical energy needs, and maintain clean and green environmental conditions, people are focusing more on renewable energy sources. Small-scale PV solar standalone AC loads or grid integration applications need high voltage at a desired level, transformer/inductor less operation, high gain DC-DC front-end converters, and DC-AC converters. To achieve all the above objectives, this paper proposes a step-up quadruple boost nine-level inverter, it works on switched capacitor technique with a reduced count of components for the application of renewable energy systems. The proposed topology balances the capacitor voltages with the control scheme itself without using any sensors. A level-shifted pulse-width modulation (LPWM) technique can be used in the control strategy of the proposed topology. This paper covers the operational modes of the proposed topology, voltage stress calculations, capacitors calculations, and losses calculations at various stages and compared with recent literature, that reveals this topology is more advantageous in terms of less total standing voltage, switch count, cost factor, better efficiency and the number of gate driver circuits. The theoretical performance can be validated through MATLAB/Simulink-based simulation and their results are validated through prototype experimentation. Further, the experimental results contain modulation index variations, frequency modulation, switching frequency variations, input voltage variations, and load variations. Finally, the max efficiency of 96.5% is achieved for the experimental prototype of the proposed topology.
- 22 March 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 11, 30442-30458
Open AccessQuadruple Boost Switched Capacitor-Based Inverter for Standalone Applications
Conventional energy sources will not be sufficient to meet future electrical demands, and also pollute the environment. Therefore, to meet their electrical energy needs, and maintain clean and green environmental conditions, people are focusing more on renewable energy sources. Small-scale PV solar standalone AC loads or grid integration applications need high voltage at a desired level, transformer/inductor less operation, high gain DC-DC front-end converters, and DC-AC converters. To achieve all the above objectives, this paper proposes a step-up quadruple boost nine-level inverter, it works on switched capacitor technique with a reduced count of components for the application of renewable energy systems. The proposed topology balances the capacitor voltages with the control scheme itself without using any sensors. A level-shifted pulse-width modulation (LPWM) technique can be used in the control strategy of the proposed topology. This paper covers the operational modes of the proposed topology, voltage stress calculations, capacitors calculations, and losses calculations at various stages and compared with recent literature, that reveals this topology is more advantageous in terms of less total standing voltage, switch count, cost factor, better efficiency and the number of gate driver circuits. The theoretical performance can be validated through MATLAB/Simulink-based simulation and their results are validated through prototype experimentation. Further, the experimental results contain modulation index variations, frequency modulation, switching frequency variations, input voltage variations, and load variations. Finally, the max efficiency of 96.5% is achieved for the experimental prototype of the proposed topology.
- Open Access
- 18 November 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 10, 121741-121761
Emerging Intelligent Bidirectional Charging Strategy Based on Recurrent Neural Network Accosting EMI and Temperature Effects for Electric Vehicle
Transportation is currently advancing towards Electric Vehicle (EV) technology. This paper presents a brief and systematic analysis of the real-time issues obtained in Electric Vehicles (EVs) due to the various ranges of energy storage devices. In general, EV energy management system is integrated with power electronic circuits for effective power conversion and reliable operation. Some issues are addressed while using the batteries in EV systems such as charging time, efficiency of battery, and raw materials. Not only battery issues but also real-time non-technical issues and operational issues are also discussed in this paper. During energy conversion with power electronic circuits, the system attains extreme temperature levels which in turn reduces the performance of the system. To maintain an optimum temperature level, it is important to study the temperature effect of the system at the most prior levels. Due to the adaption of power electronic components, some extent of noise is generated, technically treated as Electromagnetic Interference (EMI), as system capacity increases the EMI content also improved proportionately. Therefore, to mitigate the EMI effect, the low pass filter-based EMI filter is introduced in the system such that the noise level is suppressed. Bidirectional Charging System (BCS) is one of the emerging technologies in EV to obtain autonomous power supply systems in the form of Vehicle to Grid (V2G), Grid to Vehicle (G2V), and Vehicle to Load (V2L). To know the behaviour of BCS the proposed RNN controller is employed and is compared with ANN bidirectional charging model. BCS charging system with RNN controller has better dynamic response to exchange the power via DC/DC converter and AC/DC converter as compared to ANN controller.
- 18 November 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 10, 121741-121761
Open AccessEmerging Intelligent Bidirectional Charging Strategy Based on Recurrent Neural Network Accosting EMI and Temperature Effects for Electric Vehicle
Transportation is currently advancing towards Electric Vehicle (EV) technology. This paper presents a brief and systematic analysis of the real-time issues obtained in Electric Vehicles (EVs) due to the various ranges of energy storage devices. In general, EV energy management system is integrated with power electronic circuits for effective power conversion and reliable operation. Some issues are addressed while using the batteries in EV systems such as charging time, efficiency of battery, and raw materials. Not only battery issues but also real-time non-technical issues and operational issues are also discussed in this paper. During energy conversion with power electronic circuits, the system attains extreme temperature levels which in turn reduces the performance of the system. To maintain an optimum temperature level, it is important to study the temperature effect of the system at the most prior levels. Due to the adaption of power electronic components, some extent of noise is generated, technically treated as Electromagnetic Interference (EMI), as system capacity increases the EMI content also improved proportionately. Therefore, to mitigate the EMI effect, the low pass filter-based EMI filter is introduced in the system such that the noise level is suppressed. Bidirectional Charging System (BCS) is one of the emerging technologies in EV to obtain autonomous power supply systems in the form of Vehicle to Grid (V2G), Grid to Vehicle (G2V), and Vehicle to Load (V2L). To know the behaviour of BCS the proposed RNN controller is employed and is compared with ANN bidirectional charging model. BCS charging system with RNN controller has better dynamic response to exchange the power via DC/DC converter and AC/DC converter as compared to ANN controller.
- 15 November 2022
- Published by Taylor & Francis in IETE Journal of Research
- Vol. 70 (2) , 1389-1406
A Survey of Machine Learning Applications in Renewable Energy Sources
Renewable energy is now in high demand due to the deterioration of the global climate and the depletion of conventional sources. Renewable energy sources (RES) such as wind and solar are extremely intermittent, making it impossible to sustain system reliability with an unacceptably high proportion of renewable energy injection. An intrinsic attribute common to all renewable power plants is that the production of energy relies on environmental conditions such as temperature, pressure, wind speed, humidity, clouds, etc. Therefore, the power from RES cannot be completely regulated or pre-planned. It is important to forecast the amount of electricity that can be produced in a power grid for future demand. Machine learning (ML) is an emerging technology and used in all fields nowadays to perform different tasks. In this paper, the applications of machine learning in renewable energy sources are discussed. These ML techniques are mainly used to predict the power from renewable energy sources like wind, solar, hydro, biomass, tidal, and geothermal. Fault detection is a significant aspect in renewable energy systems to reduce the operation and maintenance cost and to deliver the continuous power to the loads. This paper also focusses on the use of ML techniques in predicting the faults before it occurs, early detection of faults and also to diagnose the faults in renewable energy systems. Along with the above-mentioned applications, these ML techniques used in RES for different purposes are also discussed.
- 15 November 2022
- Published by Taylor & Francis in IETE Journal of Research
- Vol. 70 (2) , 1389-1406
A Survey of Machine Learning Applications in Renewable Energy Sources
Renewable energy is now in high demand due to the deterioration of the global climate and the depletion of conventional sources. Renewable energy sources (RES) such as wind and solar are extremely intermittent, making it impossible to sustain system reliability with an unacceptably high proportion of renewable energy injection. An intrinsic attribute common to all renewable power plants is that the production of energy relies on environmental conditions such as temperature, pressure, wind speed, humidity, clouds, etc. Therefore, the power from RES cannot be completely regulated or pre-planned. It is important to forecast the amount of electricity that can be produced in a power grid for future demand. Machine learning (ML) is an emerging technology and used in all fields nowadays to perform different tasks. In this paper, the applications of machine learning in renewable energy sources are discussed. These ML techniques are mainly used to predict the power from renewable energy sources like wind, solar, hydro, biomass, tidal, and geothermal. Fault detection is a significant aspect in renewable energy systems to reduce the operation and maintenance cost and to deliver the continuous power to the loads. This paper also focusses on the use of ML techniques in predicting the faults before it occurs, early detection of faults and also to diagnose the faults in renewable energy systems. Along with the above-mentioned applications, these ML techniques used in RES for different purposes are also discussed.
- 4 October 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Emerging and Selected Topics in Industrial Electronics
- Vol. 4 (1) , 37-49
A Novel Design With Condensed Component of Multi-Input High Gain Nonisolated DC–DC Converter for Performance Enhancement in Carbon Neutral Energy Application
This article presents a multiport and multioperating DC–DC converter topology with high step-up output. The proposed converter topology includes two input ports and four switches. Compared to the recently developed topologies, the proposed topology utilizes a minimum number of components and produces high voltage gain. Modularity in shape, simple structure, continuous input, and low input current ripple are the other advantages of the proposed topology. The proposed topology enables bidirectional power flow by interchanging one of the diodes with a switch. Due to flexibility in design, the proposed topology presents a possibility for integrating multiple sources as in a renewable energy conversion system. Smooth switching between the operating modes and reduced voltage stress on switching devices are the other advantages. The working principle of the proposed converter is analyzed thoroughly in steady state. A detailed comparison is carried out considering several performance parameters to show the advantages of the proposed converter. With a proposal to extend the multi-input topology for high voltage boosting application, simulations are carried out for the dual input topology in MATLAB/Simulink platform. The performance of the converter is also validated experimentally on a dSPACE1104 control platform.
- 4 October 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Emerging and Selected Topics in Industrial Electronics
- Vol. 4 (1) , 37-49
A Novel Design With Condensed Component of Multi-Input High Gain Nonisolated DC–DC Converter for Performance Enhancement in Carbon Neutral Energy Application
This article presents a multiport and multioperating DC–DC converter topology with high step-up output. The proposed converter topology includes two input ports and four switches. Compared to the recently developed topologies, the proposed topology utilizes a minimum number of components and produces high voltage gain. Modularity in shape, simple structure, continuous input, and low input current ripple are the other advantages of the proposed topology. The proposed topology enables bidirectional power flow by interchanging one of the diodes with a switch. Due to flexibility in design, the proposed topology presents a possibility for integrating multiple sources as in a renewable energy conversion system. Smooth switching between the operating modes and reduced voltage stress on switching devices are the other advantages. The working principle of the proposed converter is analyzed thoroughly in steady state. A detailed comparison is carried out considering several performance parameters to show the advantages of the proposed converter. With a proposal to extend the multi-input topology for high voltage boosting application, simulations are carried out for the dual input topology in MATLAB/Simulink platform. The performance of the converter is also validated experimentally on a dSPACE1104 control platform.
- 15 July 2022
- Published by Walter de Gruyter GmbH in International Journal of Emerging Electric Power Systems
- Vol. 24 (5) , 635-647
A new reduced switch double boost five-level inverter with Self-Balancing of Capacitor Voltage
This paper proposes a new five-level double boost inverter based on switched capacitor technique. The proposed topology has fewer number of components and has the ability of balancing the voltage across the capacitor. The structure of the proposed topology is very simple and can be easily extended to higher number of voltage levels. The proposed generalised topology for higher gain is presented. This proposed 5-level inverter is compared with the state-of-art topologies to demonstrate the superior performance of the proposed topology. The proposed topology is simulated using MATLAB/Simulink by using the simplified control logic. Further, the power losses are calculated to find the efficiency of the proposed topology. Finally, this topology is tested in laboratory for the performance verification and the results are included.
- 15 July 2022
- Published by Walter de Gruyter GmbH in International Journal of Emerging Electric Power Systems
- Vol. 24 (5) , 635-647
A new reduced switch double boost five-level inverter with Self-Balancing of Capacitor Voltage
This paper proposes a new five-level double boost inverter based on switched capacitor technique. The proposed topology has fewer number of components and has the ability of balancing the voltage across the capacitor. The structure of the proposed topology is very simple and can be easily extended to higher number of voltage levels. The proposed generalised topology for higher gain is presented. This proposed 5-level inverter is compared with the state-of-art topologies to demonstrate the superior performance of the proposed topology. The proposed topology is simulated using MATLAB/Simulink by using the simplified control logic. Further, the power losses are calculated to find the efficiency of the proposed topology. Finally, this topology is tested in laboratory for the performance verification and the results are included.
- Open Access
- 13 July 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 10, 73931-73944
A New Reduced Switch Seven-Level Triple Boost Switched Capacitor Based Inverter
This paper proposes a new reduced switch count seven-level triple boost inverter based on switched capacitor technique. The proposed topology has fewer number of components and has the ability of balancing the voltage across the capacitors. The structure of the proposed topology is very simple and can be easily extended to higher number of voltage levels. The generalized structure for higher number of levels is presented. The level shifted pulse width modulation approach is used to evaluate the proposed topology. In addition, design of switched capacitors and power loss calculation of semiconductor switches are provided. This proposed inverter topology is compared with the state-of-art topologies to demonstrate its superior performance. Further, thermal modelling of the topology is done in PLECS to calculate the power losses and efficiency. Finally, this proposed 7-level topology is simulated using MATLAB/Simulink and tested on experimental prototype for the performance verification and the results are included.
- 13 July 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 10, 73931-73944
Open AccessA New Reduced Switch Seven-Level Triple Boost Switched Capacitor Based Inverter
This paper proposes a new reduced switch count seven-level triple boost inverter based on switched capacitor technique. The proposed topology has fewer number of components and has the ability of balancing the voltage across the capacitors. The structure of the proposed topology is very simple and can be easily extended to higher number of voltage levels. The generalized structure for higher number of levels is presented. The level shifted pulse width modulation approach is used to evaluate the proposed topology. In addition, design of switched capacitors and power loss calculation of semiconductor switches are provided. This proposed inverter topology is compared with the state-of-art topologies to demonstrate its superior performance. Further, thermal modelling of the topology is done in PLECS to calculate the power losses and efficiency. Finally, this proposed 7-level topology is simulated using MATLAB/Simulink and tested on experimental prototype for the performance verification and the results are included.