Hyusein Yemendzhiev
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Hyusein Yemendzhiev has a total of 30 co-authors. Here are the top co-authors by number of shared publications:
- Valentin Nenov
Bourgas University
4 shared publications - Ralitza Koleva
Department of Chemical Technologies, Faculty of Technical Sceince, “Prof. Asen Zlatarov” Universty, Y. Yakimov Blvd No. 1, 8010 Burgas, Bulgaria
3 shared publications - Yana Mersinkova
Competence Centre “Clean Technologies for Sustainable Environment—Water, Waste, Energy for Circular Economy” (Clean & Circle), Burgas State University “Prof. Dr. Assen Zlatarov”, 8010 Burgas, Bulgaria
3 shared publications - Albert Krastanov
Department of Microbiology and Biotechnology, Technological Faculty, University of Food Technologies, 26 Maritsa Blvd., Marasha, 4002 Plovdiv, Bulgaria
2 shared publications - Zlatka Alexieva
Department of General Microbiology, Institute of Microbiology, Bulgarian Academy of Sciences, 1113 Sofia, Bulgaria
2 shared publications Ana Maksimovic
Independent Consultant, Belgrade, Serbia
1 shared publication
Latest Publications
- Open Access
Bioelectrochemical and Anaerobic Processes for Sustainable Wastewater Valorization: Mechanisms, Resource Recovery, and Circular Economy Integration
Conventional anaerobic digestion (AD), despite its proven efficiency in wastewater treatment, faces limitations due to energy requirements and extended hydraulic retention times, with methane yields from waste-activated sludge rarely exceeding 50% of the stoichiometric maximum at retention times of 20 days or more and with the resulting biogas containing 50–75% methane. It also has a constrained capacity for high-grade resource valorization except energy in the form of methane-enriched biogas. This review focuses on bioelectrochemical systems (BES) and hybrid configurations as promising alternatives for sustainable wastewater management. BES mechanisms, including microbial fuel cells (MFC), microbial electrolysis cells (MEC), and microbial electrosynthesis (MES), are analyzed in detail, with emphasis on their capacity to directly convert organic pollutants into electricity or high-value chemicals (hydrogen, acetate) with minimal external energy input. Key advantages include potential electrical energy production, significantly reduced excess sludge production, and high level of waste mineralization. Reported performance reaches power densities of 2203 and 4990 mW/m2 for sludge-fed microbial fuel cells and up to 26,680 mW/m2 in algae-assisted configurations, chemical oxygen demand (COD) removal of up to 92%, and excess sludge production of 0.09 g/g COD against 0.159 g/g COD for anaerobic digestion treating the same stream. Limitations in terms of scalability and capital costs remain barriers to industrial implementation. Special attention is given to hybrid configurations integrating BES with AD through direct interspecies electron transfer (DIET), which accelerates biodegradation kinetics and enhances resource recovery pathways; compiled MEC-AD data report methane increases of about 3–228% over unpolarized controls, and in a 1.7 L reactor treating alkaline-thermally pretreated waste-activated sludge, the optimum of 0.6 V raised the methane yield from 213.2 ± 9.5 to 308.7 ± 5.9 mL CH4/g COD removed. These integrated approaches close material and energy cycles, enabling the simultaneous recovery of energy, nutrients (N, P), and bio-chemicals, transforming wastewater treatment plants into zero-waste biorefineries aligned with circular economy principles.
Open AccessBioelectrochemical and Anaerobic Processes for Sustainable Wastewater Valorization: Mechanisms, Resource Recovery, and Circular Economy Integration
Conventional anaerobic digestion (AD), despite its proven efficiency in wastewater treatment, faces limitations due to energy requirements and extended hydraulic retention times, with methane yields from waste-activated sludge rarely exceeding 50% of the stoichiometric maximum at retention times of 20 days or more and with the resulting biogas containing 50–75% methane. It also has a constrained capacity for high-grade resource valorization except energy in the form of methane-enriched biogas. This review focuses on bioelectrochemical systems (BES) and hybrid configurations as promising alternatives for sustainable wastewater management. BES mechanisms, including microbial fuel cells (MFC), microbial electrolysis cells (MEC), and microbial electrosynthesis (MES), are analyzed in detail, with emphasis on their capacity to directly convert organic pollutants into electricity or high-value chemicals (hydrogen, acetate) with minimal external energy input. Key advantages include potential electrical energy production, significantly reduced excess sludge production, and high level of waste mineralization. Reported performance reaches power densities of 2203 and 4990 mW/m2 for sludge-fed microbial fuel cells and up to 26,680 mW/m2 in algae-assisted configurations, chemical oxygen demand (COD) removal of up to 92%, and excess sludge production of 0.09 g/g COD against 0.159 g/g COD for anaerobic digestion treating the same stream. Limitations in terms of scalability and capital costs remain barriers to industrial implementation. Special attention is given to hybrid configurations integrating BES with AD through direct interspecies electron transfer (DIET), which accelerates biodegradation kinetics and enhances resource recovery pathways; compiled MEC-AD data report methane increases of about 3–228% over unpolarized controls, and in a 1.7 L reactor treating alkaline-thermally pretreated waste-activated sludge, the optimum of 0.6 V raised the methane yield from 213.2 ± 9.5 to 308.7 ± 5.9 mL CH4/g COD removed. These integrated approaches close material and energy cycles, enabling the simultaneous recovery of energy, nutrients (N, P), and bio-chemicals, transforming wastewater treatment plants into zero-waste biorefineries aligned with circular economy principles.
- Open Access
- 5 June 2025
- Published by MDPI AG in Applied Sciences
- Vol. 15 (11) , 6333
Mycelium-Based Composites Derived from Lignocellulosic Residual By-Products: An Insight into Their Physico-Mechanical Properties and Biodegradation Profile
The bio-fabrication of sustainable mycelium-based composites (MBCs) from renewable plant by-products offers a promising approach to reducing resource depletion and supporting the transition to a circular economy. In this research, MBCs were obtained by cultivating Ganoderma resinaceum GA1M on essential oils and agricultural by-products: hexane-extracted rose flowers (HERF), steam-distilled lavender straw (SDLS), wheat straw (WS), and pine sawdust (PS), used as single or mixed substrates. The basic physical and mechanical properties revealed that MBCs perform comparably to high-efficiency thermal insulating and conventional construction materials. The relatively low apparent density, ranging from 110 kg/m3 for WS-based to 250 kg/m3 for HERF-based composites, results in thermal conductivity values between 0.043 W/mK and 0.054 W/mK. Compression stress (40–180 kPa at 10% deformation) also revealed the good performance of the composites. The MBCs had high water absorption due to open porosity, necessitating further optimization to reduce hydrophilicity and meet intended use requirements. An aerobic biodegradation test using respirometry indicated ongoing microbial decomposition for all tested bio-composites. Notably, composites from mixed HERF and WS (50:50) showed the most rapid degradation, achieving over 46% of theoretical oxygen consumption for complete mineralization. The practical applications of MBCs depend on achieving a balance between biodegradability and stability.
- 5 June 2025
- Published by MDPI AG in Applied Sciences
- Vol. 15 (11) , 6333
Open AccessMycelium-Based Composites Derived from Lignocellulosic Residual By-Products: An Insight into Their Physico-Mechanical Properties and Biodegradation Profile
The bio-fabrication of sustainable mycelium-based composites (MBCs) from renewable plant by-products offers a promising approach to reducing resource depletion and supporting the transition to a circular economy. In this research, MBCs were obtained by cultivating Ganoderma resinaceum GA1M on essential oils and agricultural by-products: hexane-extracted rose flowers (HERF), steam-distilled lavender straw (SDLS), wheat straw (WS), and pine sawdust (PS), used as single or mixed substrates. The basic physical and mechanical properties revealed that MBCs perform comparably to high-efficiency thermal insulating and conventional construction materials. The relatively low apparent density, ranging from 110 kg/m3 for WS-based to 250 kg/m3 for HERF-based composites, results in thermal conductivity values between 0.043 W/mK and 0.054 W/mK. Compression stress (40–180 kPa at 10% deformation) also revealed the good performance of the composites. The MBCs had high water absorption due to open porosity, necessitating further optimization to reduce hydrophilicity and meet intended use requirements. An aerobic biodegradation test using respirometry indicated ongoing microbial decomposition for all tested bio-composites. Notably, composites from mixed HERF and WS (50:50) showed the most rapid degradation, achieving over 46% of theoretical oxygen consumption for complete mineralization. The practical applications of MBCs depend on achieving a balance between biodegradability and stability.
- Open Access
Evaluation of Heavy Metal Adsorption Efficiency of Biochars Derived from Agricultural Waste
This study investigates the potential of biochars derived from agricultural waste biomass for the removal of heavy metal ions from aqueous solutions. Biochars were produced via slow pyrolysis at 793 K using almond shells (AS), walnut shells (WS), pistachio shells (PS), and rice husks (RH) as feedstocks. The physicochemical properties and adsorption performance of the resulting materials were evaluated with respect to Cd(II), Mn(II), Co(II), Ni(II), Zn(II), total Iron (Fetot), total Arsenic (Astot), and total Chromium (Crtot) in model solutions. Surface morphology, porosity, and surface chemistry of the biochars were characterized by scanning electron microscopy (SEM), nitrogen adsorption at 77 K (for specific surface area and pore structure), Fourier-transform infrared spectroscopy (FTIR), and determination of the point of zero charge (pHpzc). Based on their textural properties, biochars derived from WS, PS, and AS were classified as predominantly microporous, while RH-derived biochar exhibited mesoporous characteristics. The highest Brunauer–Emmett–Teller (SBET) surface area was recorded for PS biochar, while RH biochar showed the lowest. The pistachio shell biochar exhibited the highest specific surface area (440 m2/g), while the rice husk biochar was predominantly mesoporous. Batch adsorption experiments were conducted at 25 °C, with an adsorbent dose of 3 g/L and a contact time of 24 h. The experiments in multicomponent systems revealed removal efficiencies exceeding 87% for all tested metals, with maximum values reaching 99.9% for Cd(II) and 97.5% for Fetot. The study highlights strong correlations between physicochemical properties and sorption performance, demonstrating the suitability of these biochars as low-cost sorbents for complex water treatment applications.
Open AccessEvaluation of Heavy Metal Adsorption Efficiency of Biochars Derived from Agricultural Waste
This study investigates the potential of biochars derived from agricultural waste biomass for the removal of heavy metal ions from aqueous solutions. Biochars were produced via slow pyrolysis at 793 K using almond shells (AS), walnut shells (WS), pistachio shells (PS), and rice husks (RH) as feedstocks. The physicochemical properties and adsorption performance of the resulting materials were evaluated with respect to Cd(II), Mn(II), Co(II), Ni(II), Zn(II), total Iron (Fetot), total Arsenic (Astot), and total Chromium (Crtot) in model solutions. Surface morphology, porosity, and surface chemistry of the biochars were characterized by scanning electron microscopy (SEM), nitrogen adsorption at 77 K (for specific surface area and pore structure), Fourier-transform infrared spectroscopy (FTIR), and determination of the point of zero charge (pHpzc). Based on their textural properties, biochars derived from WS, PS, and AS were classified as predominantly microporous, while RH-derived biochar exhibited mesoporous characteristics. The highest Brunauer–Emmett–Teller (SBET) surface area was recorded for PS biochar, while RH biochar showed the lowest. The pistachio shell biochar exhibited the highest specific surface area (440 m2/g), while the rice husk biochar was predominantly mesoporous. Batch adsorption experiments were conducted at 25 °C, with an adsorbent dose of 3 g/L and a contact time of 24 h. The experiments in multicomponent systems revealed removal efficiencies exceeding 87% for all tested metals, with maximum values reaching 99.9% for Cd(II) and 97.5% for Fetot. The study highlights strong correlations between physicochemical properties and sorption performance, demonstrating the suitability of these biochars as low-cost sorbents for complex water treatment applications.
- 1 May 2024
- Published by Walter de Gruyter GmbH in Zeitschrift für Naturforschung C
- Vol. 79 (5-6) , 149-153
Enhancing microbial fuel cell performance through microbial immobilization
Bio-electrochemical Systems (BES), particularly Microbial Fuel Cells (MFC), have emerged as promising technologies in environmental biotechnology. This study focused on optimizing the anode bacterial culture immobilization process to enhance BES performance. The investigation combines and modifies two key immobilization methods: covalent bonding with glutaraldehyde and inclusion in a chitosan gel in order to meet the criteria and requirements of the bio-anodes in MFC. The performance of MFCs with immobilized and suspended cultures was compared in parallel experiments. Both types showed similar substrate utilization dynamics with slight advantage of the immobilized bio-anode considering the lower concentration of biomass. The immobilized MFC exhibited higher power generation and metabolic activity, as well. Probably, this is due to improved anodic respiration and higher coulombic efficiency of the reactor. Analysis of organic acids content supported this conclusion showing significant inhibition of the fermentation products production in the MFC reactor with immobilized anode culture.
- 1 May 2024
- Published by Walter de Gruyter GmbH in Zeitschrift für Naturforschung C
- Vol. 79 (5-6) , 149-153
Enhancing microbial fuel cell performance through microbial immobilization
Bio-electrochemical Systems (BES), particularly Microbial Fuel Cells (MFC), have emerged as promising technologies in environmental biotechnology. This study focused on optimizing the anode bacterial culture immobilization process to enhance BES performance. The investigation combines and modifies two key immobilization methods: covalent bonding with glutaraldehyde and inclusion in a chitosan gel in order to meet the criteria and requirements of the bio-anodes in MFC. The performance of MFCs with immobilized and suspended cultures was compared in parallel experiments. Both types showed similar substrate utilization dynamics with slight advantage of the immobilized bio-anode considering the lower concentration of biomass. The immobilized MFC exhibited higher power generation and metabolic activity, as well. Probably, this is due to improved anodic respiration and higher coulombic efficiency of the reactor. Analysis of organic acids content supported this conclusion showing significant inhibition of the fermentation products production in the MFC reactor with immobilized anode culture.
- Open Access
Microbial Electrolysis Cell Exergy Evaluation
Bio-electrochemical systems have increasingly become the focus of research due to their potential in environmental biotechnology, particularly in the domains of waste utilization and energy recovery. A prominent method within this domain is the transformation of organic matter into hydrogen via microbial electrolysis cells (MECs). This study offers a thorough analysis of MEC performance, employing exergy analysis and incorporating relevant data from the existing literature. The findings of this research indicate a relationship between process efficiency and effective electron transfer originating from biological oxidation to the cathode reaction, facilitating hydrogen generation. The assessment performed revealed that the exergy efficiency of the process varies by a wide range, depending on conditions such as substrate type and concentration, applied external voltage, and the presence of specific inhibitors. This interplay between substrate concentration, overall efficiency, and energy requirement underlines the complex dynamics of optimizing MEC performance. Our insights provide understanding of the challenges in bio-electrochemical systems, offering implications for their sustainable and efficient use in environmental biotechnology. The theoretical analysis involved assessing the utilization of glucose and glycerol, along with the evaluation of electrical energy consumption and hydrogen yield. Our results demonstrate that a higher applied voltage is associated with greater exergy efficiency. Furthermore, after comparing the use of glucose and glycerol as substrates, our study supports the preferential application of glucose for enhanced efficiency.
Open AccessMicrobial Electrolysis Cell Exergy Evaluation
Bio-electrochemical systems have increasingly become the focus of research due to their potential in environmental biotechnology, particularly in the domains of waste utilization and energy recovery. A prominent method within this domain is the transformation of organic matter into hydrogen via microbial electrolysis cells (MECs). This study offers a thorough analysis of MEC performance, employing exergy analysis and incorporating relevant data from the existing literature. The findings of this research indicate a relationship between process efficiency and effective electron transfer originating from biological oxidation to the cathode reaction, facilitating hydrogen generation. The assessment performed revealed that the exergy efficiency of the process varies by a wide range, depending on conditions such as substrate type and concentration, applied external voltage, and the presence of specific inhibitors. This interplay between substrate concentration, overall efficiency, and energy requirement underlines the complex dynamics of optimizing MEC performance. Our insights provide understanding of the challenges in bio-electrochemical systems, offering implications for their sustainable and efficient use in environmental biotechnology. The theoretical analysis involved assessing the utilization of glucose and glycerol, along with the evaluation of electrical energy consumption and hydrogen yield. Our results demonstrate that a higher applied voltage is associated with greater exergy efficiency. Furthermore, after comparing the use of glucose and glycerol as substrates, our study supports the preferential application of glucose for enhanced efficiency.
- 1 May 2023
- Published by Springer Nature
- p. 39-46
Water Safety and Toxicity Assessment Using Real Time Sensor Measurements and Fuzzy Logic Data Processing
- 1 May 2023
- Published by Springer Nature
- p. 39-46
Water Safety and Toxicity Assessment Using Real Time Sensor Measurements and Fuzzy Logic Data Processing
- Open Access
- 23 March 2022
- Published by Taylor & Francis in Biotechnology & Biotechnological Equipment
- Vol. 36 (1) , 142-147
Comparative study on the metabolic behaviour of anode biofilm in microbial fuel cell under different external resistance
In this study the influence of the external circuit resistance on the metabolic behaviour of anodic biofilm in Microbial fuel cell (MFC) was studied. The results obtained demonstrated that extremely low and extremely high circuit loads could deteriorate the bio-electrochemistry of anodic respiration by shifting the microbial metabolism towards typical fermentation of the substrates. The best conditions for respiration and efficient substrate mineralisation of nearly 70% were found in the MFC reactor with 0.1 kΩ resistance in the anode and cathode connecting circuit. Two species of electrochemically active bacteria were isolated from the anodic community and were taxonomically affiliated to Pseudomonas and Bacillus genera based on 16 s rRNA genes amplification and sequencing.
- 23 March 2022
- Published by Taylor & Francis in Biotechnology & Biotechnological Equipment
- Vol. 36 (1) , 142-147
Open AccessComparative study on the metabolic behaviour of anode biofilm in microbial fuel cell under different external resistance
In this study the influence of the external circuit resistance on the metabolic behaviour of anodic biofilm in Microbial fuel cell (MFC) was studied. The results obtained demonstrated that extremely low and extremely high circuit loads could deteriorate the bio-electrochemistry of anodic respiration by shifting the microbial metabolism towards typical fermentation of the substrates. The best conditions for respiration and efficient substrate mineralisation of nearly 70% were found in the MFC reactor with 0.1 kΩ resistance in the anode and cathode connecting circuit. Two species of electrochemically active bacteria were isolated from the anodic community and were taxonomically affiliated to Pseudomonas and Bacillus genera based on 16 s rRNA genes amplification and sequencing.
- Open Access
Potential Use of Microbial Fuel Cell Technology in Wastewater Treatment
Two options, in regard to applying microbial fuel cells (MFCs) in water treatment, are under discussion, namely the conversion of the chemical energy of organic substrates to electricity, as well as the use their potential to reduce different species, such as the ionic form of copper (Cu2+ converted to metal copper) and iron (Fe3+ converted to Fe2+). The high reduction potential of Cu2+ and Fe3+ makes the processes of electricity production and metal reduction, to be performed simultaneously in MFC, achievable. The electrical yield measurement during the experiments of anodic organic matter degradation by MFC in treating an artificial wastewater with chemical oxygen demand (COD) 0.6 and 1.6 g O2·dm−3, as initial COD, are given. It is demonstrated that the higher organic load is associated with better electrical yield. A comparison of MFC and conventional anaerobic digestion performance is discussed, as well. Experimental proofs of copper removal and phosphate mobilization, following the iron reduction of FePO4, are also reported.
Open AccessPotential Use of Microbial Fuel Cell Technology in Wastewater Treatment
Two options, in regard to applying microbial fuel cells (MFCs) in water treatment, are under discussion, namely the conversion of the chemical energy of organic substrates to electricity, as well as the use their potential to reduce different species, such as the ionic form of copper (Cu2+ converted to metal copper) and iron (Fe3+ converted to Fe2+). The high reduction potential of Cu2+ and Fe3+ makes the processes of electricity production and metal reduction, to be performed simultaneously in MFC, achievable. The electrical yield measurement during the experiments of anodic organic matter degradation by MFC in treating an artificial wastewater with chemical oxygen demand (COD) 0.6 and 1.6 g O2·dm−3, as initial COD, are given. It is demonstrated that the higher organic load is associated with better electrical yield. A comparison of MFC and conventional anaerobic digestion performance is discussed, as well. Experimental proofs of copper removal and phosphate mobilization, following the iron reduction of FePO4, are also reported.
- Open Access
- 1 January 2022
- Published by National Library of Serbia in Journal of the Serbian Chemical Society
- Vol. 87 (6) , 775-784
Application of microbial fuel cell for simultaneous treatment of metallurgical and municipal wastewater - а laboratory study
Microbial fuel cell (MFC) is a hybrid technology that produces electricity and recovers resources from wastewater through biocatalytic and electrochemical reactions. Metallurgical facilities in Bor, Serbia, are a source of copper-rich metallurgical wastewater, and the Town of Bor is a source of municipal wastewater rich in organic matter. The aim of this paper is to investigate the possibility of application of MFC for the treatment of metallurgical and municipal wastewater that are released into the Bor River in Serbia. A prototype of MFC was constructed for this study, and 3 sets of experiments were performed using model solutions and real wastewater. Copper was successfully removed from the treated model solution with 99.42 % efficiency. Solid copper particles were obtained with a particle size of about 1 ?m. Maximum chemical oxygen demand (COD) removal rate of 191.7 mg L-1 h-1 was observed in the anodic compartment. The impact of this study is significant because MFC was implemented for the simultaneous treatment of two types of wastewaters, one containing metals and the other containing organic matter, and both types of wastewater are released into the same river.
- 1 January 2022
- Published by National Library of Serbia in Journal of the Serbian Chemical Society
- Vol. 87 (6) , 775-784
Open AccessApplication of microbial fuel cell for simultaneous treatment of metallurgical and municipal wastewater - а laboratory study
Microbial fuel cell (MFC) is a hybrid technology that produces electricity and recovers resources from wastewater through biocatalytic and electrochemical reactions. Metallurgical facilities in Bor, Serbia, are a source of copper-rich metallurgical wastewater, and the Town of Bor is a source of municipal wastewater rich in organic matter. The aim of this paper is to investigate the possibility of application of MFC for the treatment of metallurgical and municipal wastewater that are released into the Bor River in Serbia. A prototype of MFC was constructed for this study, and 3 sets of experiments were performed using model solutions and real wastewater. Copper was successfully removed from the treated model solution with 99.42 % efficiency. Solid copper particles were obtained with a particle size of about 1 ?m. Maximum chemical oxygen demand (COD) removal rate of 191.7 mg L-1 h-1 was observed in the anodic compartment. The impact of this study is significant because MFC was implemented for the simultaneous treatment of two types of wastewaters, one containing metals and the other containing organic matter, and both types of wastewater are released into the same river.
- Open Access
- 1 January 2011
- Published by Taylor & Francis in Biotechnology & Biotechnological Equipment
- Vol. 25 (sup1) , 39-40
Degradation of Mixed Aromatic Pollutants by Trametes Versicolor Strain 1
One of the most distributed groups of industrial pollutants consists of aromatic hydrocarbons. Because of the complex nature of such wastes the obtaining of new strains able to degrade different toxic aromatic compounds in mixtures is a challenge to many scientists exploring the area of environmental microbiology.In this study the strain of white rot fungus Trametes versicolor was cultivated in a medium comprising a mixture of phenol (0.2 g/l), resorcinol (0.1 g/l), p-cresol (0.1 g/l), and o-nitrophenol (0.14 g/l). Phenol, resorcinol and p-cresol were degraded in 24 hours and then a slow o-nitrophenol degradation was observed. There was about 50% decrease of o-nitrophenol concentration in 144 hours.The degradation of the tested concentrations of phenol, resorcinol and p-cresol in a mixture showed similar characteristics as in the experiments with each of them used as a single carbon substrate. The data showed that the presence of o-nitrophenol does not influence the biodegradation rate of other co...
- 1 January 2011
- Published by Taylor & Francis in Biotechnology & Biotechnological Equipment
- Vol. 25 (sup1) , 39-40
Open AccessDegradation of Mixed Aromatic Pollutants by Trametes Versicolor Strain 1
One of the most distributed groups of industrial pollutants consists of aromatic hydrocarbons. Because of the complex nature of such wastes the obtaining of new strains able to degrade different toxic aromatic compounds in mixtures is a challenge to many scientists exploring the area of environmental microbiology.In this study the strain of white rot fungus Trametes versicolor was cultivated in a medium comprising a mixture of phenol (0.2 g/l), resorcinol (0.1 g/l), p-cresol (0.1 g/l), and o-nitrophenol (0.14 g/l). Phenol, resorcinol and p-cresol were degraded in 24 hours and then a slow o-nitrophenol degradation was observed. There was about 50% decrease of o-nitrophenol concentration in 144 hours.The degradation of the tested concentrations of phenol, resorcinol and p-cresol in a mixture showed similar characteristics as in the experiments with each of them used as a single carbon substrate. The data showed that the presence of o-nitrophenol does not influence the biodegradation rate of other co...