SDSolomon Tiruneh Dibaba

Solomon Tiruneh Dibaba

*This is an algorithmically generated author record based on publicly available information.

Solomon Tiruneh Dibaba has a total of 19 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Novel activated carbon derived from tomato waste and its composite with MoS2 for quantum dot sensitized solar cells

    by Bayisa Batu Kasaye, Megersa Wodajo Shura, Solomon Truneh Dibaba

    In this study, a novel multifunctional nanocomposite was developed by integrating molybdenum disulfide (MoS2) with activated carbon (AC) derived from tomato waste, utilizing both sustainable pyrolysis (ACF) and hydrothermal (ACH) synthesis methods. The surface areas of ACF and ACH were determined to be 480.044 and 385.883 m2/g, respectively. ACF exhibited superior structural characteristics, including higher porosity and a wider interlayer spacing (21.88°, d = 0.41 nm), compared to ACH (24.65°, d = 0.36 nm). Upon compositing ACH with MoS2, enhanced graphitization and improved electrical conductivity were observed, as indicated by a distinct XRD peak at 26.27° (d = 0.33 nm) and significant photoluminescence quenching. SEM analysis revealed a porous, sheet-like morphology for ACH, while BET confirmed its mesoporous structure and an increased active surface area of 460.93 m2/g. These attributes facilitate rapid ion diffusion and efficient electron transport, making the MoS2/ACH composite an excellent candidate for quantum dot-sensitized solar cells (QDSSCs). In addition, the nanocomposite was employed as a counter electrode in QDSSCs, exhibiting notable enhancements in power conversion efficiency. Electrochemical impedance spectroscopy demonstrated improved charge transfer kinetics, with reductions in series resistance (Rs) from 11.41 for ACF to 4.38 Ω for ACF/1T-MoS2 and charge transfer resistance (Rct), which dropped from 1202 to 178 Ω for ACF and AC/1T-MoS2, respectively. Cyclic voltammetry indicated excellent electrochemical stability, as evidenced by consistent curve shapes across multiple cycles. The synergistic interaction between the porous carbon matrix and MoS2 nanosheets underpins the material’s superior performance in renewable energy applications.

  • Open Access

    Numerical Study of High Spectral Efficiency and High-Temperature Energy Harvesting Metamaterial Emitter to Improve Thermophotovoltaic Performance

    by Sifan Tamiru, Fekadu Tolessa, Birke Alemu, Solomon Tiruneh, Abebe Belay, Gurmu Alemu, T. Gurumurthi

    Design work was done on a broadband and wide-angle selective pyramid metamaterial emitter. COMSOL Multiphysics software was used to study the emitter, which was made of tungsten and aluminum nitride. The width of the unit cell and the tungsten ground thickness were fixed while other geometric parameters, such as the base length of the pyramid, the height of the pyramid, and the thickness of the dielectric, were tuned to produce the emitters desired broadband emission. A high average emissivity over 0.96 below the cutoff wavelength (0.1μm-2.2μm) was seen in the numerical simulation. The developed metamaterial emitter also had good emissivity across a broad range of incidence angles, from 0 to 60, and was polarization independent. In addition, the planned emitter for the InGaAs cell has a better spectral efficiency than the blackbody other designed emitter. In general, the planned selective nanopyramid emitter was realized with 75 spectrum efficiency for InGaAs band gap energy (0.55eV) at 1200K, which was greater than blackbody and prior papers.


  • Open Access

    Green Synthesis Method of ZnO Nanoparticles using Extracts of Zingiber officinale and Garlic Bulb (Allium sativum) and Their Synergetic Effect for Antibacterial Activities

    by Solomon Kebede Urge, Solomon Tiruneh Dibaba, Abebe Belay Gemta

    In this paper, antibacterial activities of zinc oxide (ZnO) nanoparticles synthesized through green method using garlic bulb (Allium sativum), ginger (Zingiber officinale) extracts, and their mixture are reported. The synthesized ZnO NPs were characterized by X-ray diffraction (XRD), ultraviolet visible (UVvis), photoluminescence (PL), spectroscopy and Fourier transform infrared (FTIR) spectroscopy. The crystalline sizes of ZnO NPs synthesized using garlic bulb (Allium sativum) extract, ginger (Zingiber officinale) root extract, and their mixture were 19.8, 21.94, and 23.86nm, respectively. Similarly, the corresponding peak absorbances were 369.5, 377.5, and 374nm, respectively. The antibacterial activities of synthesized ZnO NPs were tested against gram-negative bacteria Escherichia coli (E. coli) and Pseudomonas putida (P. putida) and gram-positive bacteria Staphylococcus aureus (S. aureus) and Streptococcus pyogenes (S. pyogenes). The ZnO NPs synthesized using the mixture of garlic bulb (Allium sativum) and ginger (Z. officinale) root extract have shown maximum inhibition zone against gram-negative bacteria (P. putida: 28.670.82mm) and gram-positive bacteria (S. pyogenes: 10.670.47mm) as compared to ZnO NPs synthesized using the two extracts separately. On the other hand, ZnO NPs obtained from garlic bulb and Z. officinale root extracts exhibited maximum inhibition zone against E. coli (190.82mm) and S. aureus (16.40.47mm), respectively.


  • Open Access

    Theoretical Performance Analysis of Inverted P3HT: PCBM Based Bulk Hetero-Junction Organic Solar Cells through Simulation

    by Murad Jemal Husen, Fekadu Gochole Aga, Solomon Tiruneh Dibaba

    In this study, the role of active layer thickness, hole transport layer thickness, and electron mobility on the performance of P3HT: PCBM-based inverted organic solar cells has been investigated. The simulation has been done for device structure ITO/ZnO/P3HT: PCBM/MoO3/Ag using the general-purpose photovoltaic device model (GPVDM) program tool. The short circuit current density (Jsc), open circuit voltage (Voc), fill factor (FF), and power conversion efficiency (PCE) of the cell were determined by varying the thickness of the active layer from 140nm to 260nm, the hole transparent layer from 10nm to 40nm, and electron mobility from 0.5×10−3cm2V−1s−1 to 6.5×10−3cm2V−1s−1. The PCE improvement was observed at 220nm and 20nm active layer and hole transporting layer thickness, respectively, for 4.5×10−3cm2V−1s−1 electron mobility. The results confirmed that the thickness of the active layer, hole transport layer, and charge carrier mobility plays an important role in the performance improvement of organic solar cells.


  • Open Access

    Effect of Hydrothermal Reaction Temperature on Fluorescent Properties of Carbon Quantum Dots Synthesized from Lemon Juice for Adsorption Applications

    by Gadisa Deme, Abebe Belay, Dinsefa Mensur Andoshe, Gemechu Barsisa, Diriba Tsegaye, Solomon Tiruneh, Cherinet Seboka

    Photoluminescent carbon quantum dots (CQDs) were synthesized from lemon juice precursors via single-step, hydrothermal techniques under different temperatures to control the optical properties. The synthesized CQDs were characterized by PL, illuminated UV analyzer chamber, UVvis spectroscopy, X-ray diffractometer, Fourier-transformed infrared spectrophotometry, and zeta potential techniques. The results show that the synthesized CQDs had an excellent bluegreen emission extending up to the infrared region with high quantum yield (Φ) in the range of 1441. The effect of reaction temperature and the aging of CQDs on the emission spectra of CQDs are also investigated. Furthermore, the adsorption effect of the synthesized CQDs was evaluated on methylene blue (MB) dyes. The result indicated the synthesized CQDs have excellent adsorbent properties with a removal efficiency of 6082 and an extremely fast adsorption rate of 610−2min−1 for MB dyes.


  • Open Access

    Investigation of the Impact of Active Layer and Charge Transfer Layer Materials on the Performance of Polymer Solar Cells through Simulation

    by Fekadu Gochole Aga, Fetene Fufa Bakare, Solomon Tiruneh Dibaba, Demissie Jobir Gelmecha, Chernet Amente

    This article reports polymer solar cell performance evaluated using general-purpose photovoltaic device model (GPVDM) software for various device structures. The essential parameters of the cell such as short circuit current density (JSC), open-circuit voltage (VOC), fill factor (FF), and power conversion efficiency (PCE) are evaluated for these structures. The simulation result shows the performance of the cells could be highly affected by both interfacial and active layers. Among the demonstrated device structures, better performance is observed for device structure ITO/V2O5/PTB7:PC70BM/TiOx/Al with 10.4mA/cm2 short circuit current density, 0.89V open-circuit voltage, 59.5 fill factor, and 6.1 power conversion efficiency. The study is useful for a better understanding of the powerful effect of the materials in the device structure on the performance of the cell and thereby determines the proper device structure and materials for improving the performance of the cell.