Wenchao Zhu
Wenchao Zhu has a total of 32 co-authors. Here are the top co-authors by number of shared publications:
- Xinghua Zhang
School of Chemical and Environmental Engineering, Shanghai Institute of Technology, Shanghai 201418, China
2 shared publications Bo Chen
State Key Laboratory of NBC Protection for Civilian, Beijing, 102205, P. R. China
1 shared publication- Bomou Ma
Innovation Center for Textile Science and Technology, Donghua University, Shanghai 201620, China
1 shared publication - Chang Chen
State Key Laboratory of NBC Protection for Civilian, Beijing 102205, China
1 shared publication - Fuli Wang
State Key Laboratory of NBC Protection for Civilian, Beijing 102205, China
1 shared publication - Ge Yao
State Key Laboratory of NBC Protection for Civilian, Beijing 102205, China
1 shared publication
Latest Publications
- Open Access
Spheroidization Behavior of TiZrNbTa Refractory High-Entropy Alloy Powder During Radio Frequency Plasma Processing
Spherical TiZrNbTa refractory high-entropy alloy powders with uniform composition and good flowability are essential feedstock for powder-based additive manufacturing; however, irregular powders produced by the hydrogenation-dehydrogenation route generally require further shaping treatment. Radio frequency (RF) plasma spheroidization of TiZrNbTa refractory high-entropy alloy powders prepared by hydrogenation-dehydrogenation (HDH) was investigated at a fixed power of 12 kW. Fine (10–40 μm) and coarse (40–70 μm) powders were compared at 5.0 g/min, followed by feed-rate tests (2.5–7.5 g/min) on the coarse fraction. At 5.0 g/min, the spheroidization degrees of the fine and coarse powders were 45.33% and 50.88%, respectively. The fine powder exhibited satellite particles and a broadened particle-size distribution, whereas the coarse powder retained some irregular particles. Decreasing the coarse-powder feed rate from 7.5 to 2.5 g/min increased the spheroidization degree from 45.71% to 94.55%, with median particle size (D50) reaching 56.84 μm and a narrower particle-size distribution. The powders retained predominantly body-centered cubic (BCC) diffraction signatures, while dendritic substructures and local Ta/Zr segregation varied with processing conditions. Testing showed that untreated coarse HDH powder did not flow unaided through a Hall funnel, whereas the 5.0 g/min spheroidized product flowed in 18.7 s/50 g; after spheroidization, its loose bulk density increased from 4.68 to 5.47 g/cm3. These results clarify the effects of particle size and powder feed rate on spheroidization behavior within the investigated conditions.
Open AccessSpheroidization Behavior of TiZrNbTa Refractory High-Entropy Alloy Powder During Radio Frequency Plasma Processing
Spherical TiZrNbTa refractory high-entropy alloy powders with uniform composition and good flowability are essential feedstock for powder-based additive manufacturing; however, irregular powders produced by the hydrogenation-dehydrogenation route generally require further shaping treatment. Radio frequency (RF) plasma spheroidization of TiZrNbTa refractory high-entropy alloy powders prepared by hydrogenation-dehydrogenation (HDH) was investigated at a fixed power of 12 kW. Fine (10–40 μm) and coarse (40–70 μm) powders were compared at 5.0 g/min, followed by feed-rate tests (2.5–7.5 g/min) on the coarse fraction. At 5.0 g/min, the spheroidization degrees of the fine and coarse powders were 45.33% and 50.88%, respectively. The fine powder exhibited satellite particles and a broadened particle-size distribution, whereas the coarse powder retained some irregular particles. Decreasing the coarse-powder feed rate from 7.5 to 2.5 g/min increased the spheroidization degree from 45.71% to 94.55%, with median particle size (D50) reaching 56.84 μm and a narrower particle-size distribution. The powders retained predominantly body-centered cubic (BCC) diffraction signatures, while dendritic substructures and local Ta/Zr segregation varied with processing conditions. Testing showed that untreated coarse HDH powder did not flow unaided through a Hall funnel, whereas the 5.0 g/min spheroidized product flowed in 18.7 s/50 g; after spheroidization, its loose bulk density increased from 4.68 to 5.47 g/cm3. These results clarify the effects of particle size and powder feed rate on spheroidization behavior within the investigated conditions.
- 28 March 2024
- Published by Royal Society of Chemistry (RSC) in Green Chemistry
- Vol. 26 (9) , 5538-5545
Inorganic ligand-supported Mo oxide as a hydrogen atom transfer photocatalyst for direct C(sp2)–H phosphorylation
Visible-light-induced C(sp2)–H phosphorylation of 2H-thiozoles/quinoxalines with H-phosphine oxides was achieved using an inorganic ligand-supported Mo oxide ([N(C4H9)4]2[Mo6O19]) as a hydrogen atom transfer (HAT) photocatalyst.
- 28 March 2024
- Published by Royal Society of Chemistry (RSC) in Green Chemistry
- Vol. 26 (9) , 5538-5545
Inorganic ligand-supported Mo oxide as a hydrogen atom transfer photocatalyst for direct C(sp2)–H phosphorylation
Visible-light-induced C(sp2)–H phosphorylation of 2H-thiozoles/quinoxalines with H-phosphine oxides was achieved using an inorganic ligand-supported Mo oxide ([N(C4H9)4]2[Mo6O19]) as a hydrogen atom transfer (HAT) photocatalyst.
- Open Access
- 20 March 2024
- Published by MDPI AG in Fermentation
- Vol. 10 (3) , 173
The Biosynthesis of the Monoterpene Tricyclene in E. coli through the Appropriate Truncation of Plant Transit Peptides
Tricyclene, a tricyclic monoterpene naturally occurring in plant essential oils, holds potential for the development of medicinal and fuel applications. In this study, we successfully synthesized tricyclene in E. coli by introducing the heterologous mevalonate (MVA) pathway along with Abies grandis geranyl diphosphate synthase (GPPS) and Nicotiana sylvestris tricyclene synthase (TS) XP_009791411. Initially, the shake-flask fermentation at 30 ◦C yielded a tricyclene titer of 0.060 mg/L. By increasing the copy number of the TS-coding gene, we achieved a titer of 0.103 mg/L. To further enhance tricyclene production, optimal truncation in the N-terminal region of TS XP_009791411 resulted in an impressive highest titer of 47.671 mg/L, approximately a 794.5-fold improvement compared to its wild-type counterpart. To the best of our knowledge, this is the highest titer of the heterologous synthesis of tricyclene in E. coli. The SDS-PAGE analysis revealed that lowering induction temperature and truncating the random coil N-terminal region effectively improved TS solubility, which was closely associated with tricyclene production levels. Furthermore, by truncating other TSs, the titers of tricyclene were improved to different degrees.
- 20 March 2024
- Published by MDPI AG in Fermentation
- Vol. 10 (3) , 173
Open AccessThe Biosynthesis of the Monoterpene Tricyclene in E. coli through the Appropriate Truncation of Plant Transit Peptides
Tricyclene, a tricyclic monoterpene naturally occurring in plant essential oils, holds potential for the development of medicinal and fuel applications. In this study, we successfully synthesized tricyclene in E. coli by introducing the heterologous mevalonate (MVA) pathway along with Abies grandis geranyl diphosphate synthase (GPPS) and Nicotiana sylvestris tricyclene synthase (TS) XP_009791411. Initially, the shake-flask fermentation at 30 ◦C yielded a tricyclene titer of 0.060 mg/L. By increasing the copy number of the TS-coding gene, we achieved a titer of 0.103 mg/L. To further enhance tricyclene production, optimal truncation in the N-terminal region of TS XP_009791411 resulted in an impressive highest titer of 47.671 mg/L, approximately a 794.5-fold improvement compared to its wild-type counterpart. To the best of our knowledge, this is the highest titer of the heterologous synthesis of tricyclene in E. coli. The SDS-PAGE analysis revealed that lowering induction temperature and truncating the random coil N-terminal region effectively improved TS solubility, which was closely associated with tricyclene production levels. Furthermore, by truncating other TSs, the titers of tricyclene were improved to different degrees.
- Open Access
A Sprayable and Visible Light Rapid-Cured Strippable Film for Surface Radioactive Decontamination
Strippable film is effective for removing radioactive contamination. However, it still has some limitations, such as the long curing time (about 30 min~24 h) and the requirement of organic solvents. To address these issues, we report a simple protocol to prepare strippable decontamination films using liquid polybutadiene (LPB) and tert-butyl acrylate (TBA) as the raw materials without solvent and using camphorquinone/ethyl 4-dimethylaminobenzoate (CQ/EDB) as a photoinitiator, where the film was formed under household LED panel light or daylight irradiation for about 540 s. After a thorough study of viscosity, real-time Fourier transform infrared (RT-FTIR spectra), gel and volatile organic compound (VOC) contents, mechanical properties and decontamination efficiency, the optimum composition and curing conditions were determined for the decontamination strippable film. VOC content is as low as 12.7 ± 0.7% and the resultant strippable film exhibits good mechanical performances with a tensile strength of up to 5.4 ± 0.4 MPa and elongation of up to 66.6 ± 13%. Most important, the decontamination efficiencies of this strippable film for 133CsCl on glass, ceramic and metal surfaces reach up to 98.1%, 94.3% and 97.6%, respectively.
Open AccessA Sprayable and Visible Light Rapid-Cured Strippable Film for Surface Radioactive Decontamination
Strippable film is effective for removing radioactive contamination. However, it still has some limitations, such as the long curing time (about 30 min~24 h) and the requirement of organic solvents. To address these issues, we report a simple protocol to prepare strippable decontamination films using liquid polybutadiene (LPB) and tert-butyl acrylate (TBA) as the raw materials without solvent and using camphorquinone/ethyl 4-dimethylaminobenzoate (CQ/EDB) as a photoinitiator, where the film was formed under household LED panel light or daylight irradiation for about 540 s. After a thorough study of viscosity, real-time Fourier transform infrared (RT-FTIR spectra), gel and volatile organic compound (VOC) contents, mechanical properties and decontamination efficiency, the optimum composition and curing conditions were determined for the decontamination strippable film. VOC content is as low as 12.7 ± 0.7% and the resultant strippable film exhibits good mechanical performances with a tensile strength of up to 5.4 ± 0.4 MPa and elongation of up to 66.6 ± 13%. Most important, the decontamination efficiencies of this strippable film for 133CsCl on glass, ceramic and metal surfaces reach up to 98.1%, 94.3% and 97.6%, respectively.