Eirik Bjørndal Njåstad
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Eirik Bjørndal Njåstad has a total of 8 co-authors. Here are the top co-authors by number of shared publications:
- Olav Egeland
Norwegian University of Science and Technology (NTNU)
2 shared publications - Andrei Lobov
Norwegian University of Science and Technology, Trondheim, Norway
1 shared publication - Andrej Cibicik
Department of Production Technology, SINTEF Manufacturing AS, Trondheim, Norway
1 shared publication - Lars Tingelstad
Department of Mechanical and Industrial Engineering, Norwegian University of Science and Technology (NTNU), 7034 Trondheim, Norway
1 shared publication - Morten Bjelland
Leirvik AS, Stord, Norway
1 shared publication - Ole Terje Midling
Marine Aluminium AS, Avaldsnes, Norway
1 shared publication
Latest Publications
- Open Access
- 8 March 2023
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 126 (3-4) , 1175-1187
Generation of rule-adhering robot programs for aluminium welding automatically from CAD
This paper presents a method to automatically generate robot welding programs from CAD to address the ever-constant demand for product customisation. Furthermore, to ensure that proper welding operations and structural integrity are met, the generated programs also consider the welding conditions and requirements. These welding conditions and requirements are defined by the weld direction and face relative to gravity and surrounding geometry, which has not been observed in the present research sphere. To achieve this, the approach leverages information that can be extracted from a topological analysis of tessellated geometry local to the weld joint in conjunction with available CAD API functions. Finally, an implementation of the method using Siemens NX and the Robotics Toolbox for Python is presented and tested on three geometrically different node configurations and a stiffener piece provided by industrial collaborators. In all, the proposed system was able to correctly generate programs adhering to allowed welding operations as long as a solution existed. For the more complex node configurations (which require reorientation when welded by humans), 32 weld path programs out of 42 were generated based on the given criteria. For the least complex node, a total of 20 out of 24 were generated with the same criteria. All 14 weld programs were generated for the stiffener representation.
- 8 March 2023
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 126 (3-4) , 1175-1187
Open AccessGeneration of rule-adhering robot programs for aluminium welding automatically from CAD
This paper presents a method to automatically generate robot welding programs from CAD to address the ever-constant demand for product customisation. Furthermore, to ensure that proper welding operations and structural integrity are met, the generated programs also consider the welding conditions and requirements. These welding conditions and requirements are defined by the weld direction and face relative to gravity and surrounding geometry, which has not been observed in the present research sphere. To achieve this, the approach leverages information that can be extracted from a topological analysis of tessellated geometry local to the weld joint in conjunction with available CAD API functions. Finally, an implementation of the method using Siemens NX and the Robotics Toolbox for Python is presented and tested on three geometrically different node configurations and a stiffener piece provided by industrial collaborators. In all, the proposed system was able to correctly generate programs adhering to allowed welding operations as long as a solution existed. For the more complex node configurations (which require reorientation when welded by humans), 32 weld path programs out of 42 were generated based on the given criteria. For the least complex node, a total of 20 out of 24 were generated with the same criteria. All 14 weld programs were generated for the stiffener representation.
- Open Access
- 17 March 2022
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 120 (7-8) , 4525-4538
Robotic weld groove scanning for large tubular T-joints using a line laser sensor
This paper presents a novel procedure for robotic scanning of weld grooves in large tubular T-joints. The procedure is designed to record the discrete weld groove scans using a commercially available line laser scanner which is attached to the robot end-effector. The advantage of the proposed algorithm is that it does not require any prior knowledge of the joint interface geometry, while only two initial scanning positions have to be specified. The position and orientation of the following scan are calculated using the data from two previous weld groove scans, so once initiated, the scanning process is fully autonomous. The procedure is a two-step algorithm consisting of the prediction and correction substeps, where the position and orientation of the sensor for the following scan are predicted and corrected. Such a procedure does not require frequent weld groove scanning for navigation along the groove. The performance of the proposed procedure is studied experimentally using an industrial-size T-joint specimen. Several cases of scanning motion parameters have been tested, and a discussion on the results is given.
- 17 March 2022
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 120 (7-8) , 4525-4538
Open AccessRobotic weld groove scanning for large tubular T-joints using a line laser sensor
This paper presents a novel procedure for robotic scanning of weld grooves in large tubular T-joints. The procedure is designed to record the discrete weld groove scans using a commercially available line laser scanner which is attached to the robot end-effector. The advantage of the proposed algorithm is that it does not require any prior knowledge of the joint interface geometry, while only two initial scanning positions have to be specified. The position and orientation of the following scan are calculated using the data from two previous weld groove scans, so once initiated, the scanning process is fully autonomous. The procedure is a two-step algorithm consisting of the prediction and correction substeps, where the position and orientation of the sensor for the following scan are predicted and corrected. Such a procedure does not require frequent weld groove scanning for navigation along the groove. The performance of the proposed procedure is studied experimentally using an industrial-size T-joint specimen. Several cases of scanning motion parameters have been tested, and a discussion on the results is given.
- Open Access
- 7 March 2022
- Published by Springer Nature in Journal of Marine Science and Technology
- Vol. 27 (2) , 887-906
Identification of the geometric design parameters of propeller blades from 3D scanning
This paper presents a new method for the identification of geometric design parameters of ISO 484 class propeller blades from scanned point cloud data. The method can be used for tolerance inspection and in-line measurement of manufactured blades, and for wear assessment and reverse engineering of propellers in service. The geometry of the propeller blades is specified by a set of blade sections stacked radially on concentric cylindrical surfaces. For each of these sections, the chord line and mean camber line is determined, and geometric design parameters such as the pitch, skew, chord length, camber, and thickness distributions are identified. The proposed method is a complete procedure for identifying the design parameters of marine propeller blades from point cloud data, and includes a novel method for the precise identification of the mean camber line based on Voronoi diagrams and Delaunay triangulation. The paper includes validation of the proposed method in experiments where reverse engineering is applied to a propeller blade of the KVLCC2 propeller, and in 3D scanning of a large, high-skew thruster blade where the results were compared to CMM measurements.
- 7 March 2022
- Published by Springer Nature in Journal of Marine Science and Technology
- Vol. 27 (2) , 887-906
Open AccessIdentification of the geometric design parameters of propeller blades from 3D scanning
This paper presents a new method for the identification of geometric design parameters of ISO 484 class propeller blades from scanned point cloud data. The method can be used for tolerance inspection and in-line measurement of manufactured blades, and for wear assessment and reverse engineering of propellers in service. The geometry of the propeller blades is specified by a set of blade sections stacked radially on concentric cylindrical surfaces. For each of these sections, the chord line and mean camber line is determined, and geometric design parameters such as the pitch, skew, chord length, camber, and thickness distributions are identified. The proposed method is a complete procedure for identifying the design parameters of marine propeller blades from point cloud data, and includes a novel method for the precise identification of the mean camber line based on Voronoi diagrams and Delaunay triangulation. The paper includes validation of the proposed method in experiments where reverse engineering is applied to a propeller blade of the KVLCC2 propeller, and in 3D scanning of a large, high-skew thruster blade where the results were compared to CMM measurements.