Patrícia Lovašiová
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Patrícia Lovašiová has a total of 16 co-authors. Here are the top co-authors by number of shared publications:
- Alena Michalcová
Department of Metals and Corrosion Engineering, University of Chemistry and Technology in Prague, Technická 5, 166 28 Prague 6, Czech Republic
1 shared publication - Dalibor Vojtěch
Department of Metals and Corrosion Engineering, University of Chemistry and Technology, Prague, Technická 5, 166 28 Prague, Czech Republic
1 shared publication - Daniel Koutný
Faculty of Mechanical Engineering Brno University of Technology Technicka 2 61669 Brno Czech Republic
1 shared publication - Enas Ghassan Hamed Alzubi
Department of metals and corrosion engineering, University of Chemistry and Technology in Prague, Technicka 5, 166 28 Prague, Czech Republic
1 shared publication - Eva Jablonská
Department of Biochemistry and Microbiology, University of Chemistry and Technology Prague, Prague, Czech Republic
1 shared publication - Ivana Zetková
Faculty of Mechanical Engineering University of West Bohemia Univerzitní 8 306 14 Pilsen Czech Republic
1 shared publication
Latest Publications
- Open Access
- 23 April 2026
- Published by Jan Evangelista Purkyne University in Usti nad Labem in Manufacturing Technology
- Vol. 26 (2) , 185-198
Influence of the Manufacturing Route on the High-Temperature Oxidation Behavior of IN718 Alloy in Simulated Modern Energy Environments
The use of supercritical water in energy applications is motivated by the aim of increasing the thermal efficiency of power systems. However, structural materials exposed to this environment may undergo corrosive degradation. The objective of ...
- 23 April 2026
- Published by Jan Evangelista Purkyne University in Usti nad Labem in Manufacturing Technology
- Vol. 26 (2) , 185-198
Open AccessInfluence of the Manufacturing Route on the High-Temperature Oxidation Behavior of IN718 Alloy in Simulated Modern Energy Environments
The use of supercritical water in energy applications is motivated by the aim of increasing the thermal efficiency of power systems. However, structural materials exposed to this environment may undergo corrosive degradation. The objective of ...
- Open Access
Biodegradable WE43 Magnesium Alloy Produced by Selective Laser Melting: Mechanical Properties, Corrosion Behavior, and In-Vitro Cytotoxicity
In this work, selective laser melting (SLM) technology was used to prepare Mg-4Y-3Nd-Zr (WE43) alloy. This alloy and production method are promising for the design of biodegradable implants. The aim of this study was to investigate the chemical composition, microstructure, mechanical properties, corrosion behavior in simulated body fluid (SBF), and cytotoxicity of the alloy produced by SLM method and to compare it with conventionally gravity cast reference alloy. Analysis of the surface of the revealed an oxygen content of 7 wt.%. Undesirable unmelted and only partially adhered spherical particles of the starting powder were also found. The microstructure of the material was very fine and consisted of α-Mg dendritic matrix, β-Mg41(Nd, Y)5 intermetallic phase, Y2O3 inclusions, and 0.6 vol.% of residual porosity. The Vickers hardness, compressive yield strength, compressive strength, and maximum compressive strain were 88 HV0.1, 201 MPa, 394 MPa, and 14%, respectively, which are close to the reference values in as-cast. The in vitro corrosion rates determined by immersion and potentiodynamic tests were 2.6 mm/year and 1.3 mm/year, respectively. Cytotoxicity tests indicated good biocompatibility of the 3D-printed alloy.
Open AccessBiodegradable WE43 Magnesium Alloy Produced by Selective Laser Melting: Mechanical Properties, Corrosion Behavior, and In-Vitro Cytotoxicity
In this work, selective laser melting (SLM) technology was used to prepare Mg-4Y-3Nd-Zr (WE43) alloy. This alloy and production method are promising for the design of biodegradable implants. The aim of this study was to investigate the chemical composition, microstructure, mechanical properties, corrosion behavior in simulated body fluid (SBF), and cytotoxicity of the alloy produced by SLM method and to compare it with conventionally gravity cast reference alloy. Analysis of the surface of the revealed an oxygen content of 7 wt.%. Undesirable unmelted and only partially adhered spherical particles of the starting powder were also found. The microstructure of the material was very fine and consisted of α-Mg dendritic matrix, β-Mg41(Nd, Y)5 intermetallic phase, Y2O3 inclusions, and 0.6 vol.% of residual porosity. The Vickers hardness, compressive yield strength, compressive strength, and maximum compressive strain were 88 HV0.1, 201 MPa, 394 MPa, and 14%, respectively, which are close to the reference values in as-cast. The in vitro corrosion rates determined by immersion and potentiodynamic tests were 2.6 mm/year and 1.3 mm/year, respectively. Cytotoxicity tests indicated good biocompatibility of the 3D-printed alloy.