Yue Zhang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Yue Zhang has a total of 10 co-authors. Here are the top co-authors by number of shared publications:
- Jin Zhou
College of Mechanical and Electrical Engineering, Nanjing University of Aeronautics and Astronautics, Nanjing 210016, China
3 shared publications - Yang Zhou
Nanjing University of Aeronautics and Astronautics
3 shared publications Runhui Yao
Nanjing University of Aeronautics and Astronautics
2 shared publications- Jin Zhou1 shared publication
- Renkun Zhang1 shared publication
- Xiaoming Han
College of Mechanical and Electrical Engineering, Nanjing University of Aeronautics and Astronautics, Nanjing, China
1 shared publication
Latest Publications
- 1 October 2024
- Published by Elsevier in Mechanical Systems and Signal Processing
- Vol. 224
Unbalance compensation based on speed fault-tolerance and fusion strategy for magnetically suspended PMSM
- 1 October 2024
- Published by Elsevier in Mechanical Systems and Signal Processing
- Vol. 224
Unbalance compensation based on speed fault-tolerance and fusion strategy for magnetically suspended PMSM
- 15 May 2023
- Published by SAGE Publications in Journal of Vibration and Control
- Vol. 30 (9-10) , 2059-2071
Optimal phase compensation for a rotor-AMB system considering interface contact
Rotor-Active magnetic bearing (rotor-AMB) systems offer significant advantages in power consumption and are increasingly being applied in fluid machinery. However, in such machinery, the impeller and the rotor are commonly connected by bolt fastening. Once a certain pre-tightening force is applied to the bolted connection and the interface contact between the rotor and the impeller is formed, the flexible modal vibration will be excited when the rotor is levitated. The conventional Proportional-Integral-Derivative (PID) controller is limited in this vibration suppression and it is essential to increase the damping at bending mode to inhibit vibration. However, the calculation of the optimal phase compensated is based on the rotor-AMB model considering interface contact. In this work, the effect of the interface contact is equivalent to massless spring units, and the disturbance generated by spring units is acted upon the mechatronic system in the way of positive feedback. The detailed description of the transfer function from the disturbance to rotor deformation at fourth bending mode is obtained by theoretical model and system identification. The optimal phase of the system needed to inhibit the disturbance is determined by minimizing the gain of the transfer function at fourth bending mode. A combination of PID control and phase compensation is implemented in the experiment. The results show that the optimal phase is 50° as the calculation and the optimal phase compensation control can sufficiently inhibit the modal vibration.
- 15 May 2023
- Published by SAGE Publications in Journal of Vibration and Control
- Vol. 30 (9-10) , 2059-2071
Optimal phase compensation for a rotor-AMB system considering interface contact
Rotor-Active magnetic bearing (rotor-AMB) systems offer significant advantages in power consumption and are increasingly being applied in fluid machinery. However, in such machinery, the impeller and the rotor are commonly connected by bolt fastening. Once a certain pre-tightening force is applied to the bolted connection and the interface contact between the rotor and the impeller is formed, the flexible modal vibration will be excited when the rotor is levitated. The conventional Proportional-Integral-Derivative (PID) controller is limited in this vibration suppression and it is essential to increase the damping at bending mode to inhibit vibration. However, the calculation of the optimal phase compensated is based on the rotor-AMB model considering interface contact. In this work, the effect of the interface contact is equivalent to massless spring units, and the disturbance generated by spring units is acted upon the mechatronic system in the way of positive feedback. The detailed description of the transfer function from the disturbance to rotor deformation at fourth bending mode is obtained by theoretical model and system identification. The optimal phase of the system needed to inhibit the disturbance is determined by minimizing the gain of the transfer function at fourth bending mode. A combination of PID control and phase compensation is implemented in the experiment. The results show that the optimal phase is 50° as the calculation and the optimal phase compensation control can sufficiently inhibit the modal vibration.
- 3 March 2022
- Published by SAGE Publications in Journal of Vibration and Control
- Vol. 29 (9-10) , 2077-2085
Adaptive odd repetitive control for magnetically suspended rotor harmonic currents suppression
Magnetic levitation rotating machinery has been widely used in industrial applications. Odd harmonic currents in the active magnetic bearing coils, which are caused by rotor mass unbalance and sensor runout, increase the power consumption and the base vibration. Repetitive control has recently been used to suppress harmonic currents in magnetic bearing systems. However, repetitive control needs the rotor rotational speed information and has some limitations without a speed sensor. In this paper, an adaptive odd repetitive control which does not need the speed sensors is proposed to suppress the active magnetic bearing odd harmonic currents. Compared to the conventional repetitive control, the second-order generalized integral frequency-locked loop is applied in adaptive odd repetitive control to estimate the rotor speed in real time without additional speed sensors. The magnetically suspended rotor with harmonic disturbances is modeled. The work principle, structure, and design of the adaptive odd repetitive control are addressed. The simulation and experiments are carried out on a rotor active magnetic bearing test rig to validate the effectiveness of the proposed adaptive odd repetitive control, and the results show that the active magnetic bearing odd harmonic currents are well suppressed.
- 3 March 2022
- Published by SAGE Publications in Journal of Vibration and Control
- Vol. 29 (9-10) , 2077-2085
Adaptive odd repetitive control for magnetically suspended rotor harmonic currents suppression
Magnetic levitation rotating machinery has been widely used in industrial applications. Odd harmonic currents in the active magnetic bearing coils, which are caused by rotor mass unbalance and sensor runout, increase the power consumption and the base vibration. Repetitive control has recently been used to suppress harmonic currents in magnetic bearing systems. However, repetitive control needs the rotor rotational speed information and has some limitations without a speed sensor. In this paper, an adaptive odd repetitive control which does not need the speed sensors is proposed to suppress the active magnetic bearing odd harmonic currents. Compared to the conventional repetitive control, the second-order generalized integral frequency-locked loop is applied in adaptive odd repetitive control to estimate the rotor speed in real time without additional speed sensors. The magnetically suspended rotor with harmonic disturbances is modeled. The work principle, structure, and design of the adaptive odd repetitive control are addressed. The simulation and experiments are carried out on a rotor active magnetic bearing test rig to validate the effectiveness of the proposed adaptive odd repetitive control, and the results show that the active magnetic bearing odd harmonic currents are well suppressed.