Mohammad Asad
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Mohammad Asad has a total of 28 co-authors. Here are the top co-authors by number of shared publications:
- Tatheer Zahra
Group of Sustainable Engineered Construction Materials, School of Civil & Environmental Engineering, Faculty of Engineering, Queensland University of Technology, 2 George St., Brisbane, QLD 4000, Australia
15 shared publications - Julian Thamboo
South Eastern University of Sri Lanka
10 shared publications - Yan Zhuge
UniSA STEM, University of South Australia, Adelaide, Australia
4 shared publications Arlene Nardone
2 shared publicationsDavid P Thambiratnam
Queensland University of Technology, Brisbane, QLD, Australia
2 shared publicationsDavid P. Thambiratnam
2 shared publications
Latest Publications
- Open Access
- 10 April 2026
- Published by Elsevier in Structures
- Vol. 88
Experimental investigation on application of 3D-printed auxetic cementitious composites to strengthen concrete block masonry
- 10 April 2026
- Published by Elsevier in Structures
- Vol. 88
Open AccessExperimental investigation on application of 3D-printed auxetic cementitious composites to strengthen concrete block masonry
- Open Access
Assessment of RC Columns Under Axial Compression for Un-Corroded and Corroded Stirrups Scenarios: A Practice-Oriented Numerical Approach
This paper presents a practice-oriented numerical modelling procedure to assess the loadbearing capacity of reinforced concrete (RC) columns under axial compression loading. A simplified procedure was incorporated to analyse the performance of RC columns with corroded stirrups, a prevalent deterioration phenomenon in corroded RC columns. The modelling framework incorporates material and geometric nonlinearities caused by material and buckling failure under axial compression, utilising the Arc-length algorithm with integrated geometric imperfections. Stirrup corrosion scenarios were incorporated by removing stirrups and modifying core concrete confinement properties, providing a practice-oriented approach to assess the loadbearing capacity of corroded columns. The study focused on square RC columns that are commonly used in low-rise buildings with nominal reinforcement detailing. The modelling method was validated against experimental data, and it showed a good agreement. A comprehensive parametric analysis was then conducted to examine the effects of critical design parameters, including (1) slenderness, (2) eccentricity, (3) stirrup corrosion, and (4) material properties, on axial compression performance. Parametric analyses demonstrated that the developed modelling technique appropriately predicted the axial compression behaviour of un-corroded RC columns in alignment with analytical design rules. For stirrup-corroded RC columns, the absence of confinement for up to 300 mm length near the base, due to stirrup corrosion, led to premature buckling. Based on the analysed cases, the reduction in bearing capacity of the stirrup-corroded RC columns could range between 4.9 and 18.6% (higher for slender columns) as compared to corresponding un-corroded RC columns.
Open AccessAssessment of RC Columns Under Axial Compression for Un-Corroded and Corroded Stirrups Scenarios: A Practice-Oriented Numerical Approach
This paper presents a practice-oriented numerical modelling procedure to assess the loadbearing capacity of reinforced concrete (RC) columns under axial compression loading. A simplified procedure was incorporated to analyse the performance of RC columns with corroded stirrups, a prevalent deterioration phenomenon in corroded RC columns. The modelling framework incorporates material and geometric nonlinearities caused by material and buckling failure under axial compression, utilising the Arc-length algorithm with integrated geometric imperfections. Stirrup corrosion scenarios were incorporated by removing stirrups and modifying core concrete confinement properties, providing a practice-oriented approach to assess the loadbearing capacity of corroded columns. The study focused on square RC columns that are commonly used in low-rise buildings with nominal reinforcement detailing. The modelling method was validated against experimental data, and it showed a good agreement. A comprehensive parametric analysis was then conducted to examine the effects of critical design parameters, including (1) slenderness, (2) eccentricity, (3) stirrup corrosion, and (4) material properties, on axial compression performance. Parametric analyses demonstrated that the developed modelling technique appropriately predicted the axial compression behaviour of un-corroded RC columns in alignment with analytical design rules. For stirrup-corroded RC columns, the absence of confinement for up to 300 mm length near the base, due to stirrup corrosion, led to premature buckling. Based on the analysed cases, the reduction in bearing capacity of the stirrup-corroded RC columns could range between 4.9 and 18.6% (higher for slender columns) as compared to corresponding un-corroded RC columns.
- Open Access
- 12 September 2024
- Published by Elsevier in Journal of Building Engineering
- Vol. 97
Experimental investigation on tensile characteristics of 3D printed auxetic embedded cementitious composites and shear bonding behaviour to masonry
- 12 September 2024
- Published by Elsevier in Journal of Building Engineering
- Vol. 97
Open AccessExperimental investigation on tensile characteristics of 3D printed auxetic embedded cementitious composites and shear bonding behaviour to masonry
- Open Access
- 21 June 2024
- Published by Elsevier in Journal of Building Engineering
- Vol. 94
High strain rate effect and dynamic compressive behaviour of auxetic cementitious composites
- 21 June 2024
- Published by Elsevier in Journal of Building Engineering
- Vol. 94
Open AccessHigh strain rate effect and dynamic compressive behaviour of auxetic cementitious composites
- Open Access
- 12 February 2024
- Published by Elsevier in Journal of Building Engineering
- Vol. 86
Reinforced concrete block masonry walls under eccentric compression: Assessment using experimental and numerical data
- 12 February 2024
- Published by Elsevier in Journal of Building Engineering
- Vol. 86
Open AccessReinforced concrete block masonry walls under eccentric compression: Assessment using experimental and numerical data
- Open Access
- 17 January 2024
- Published by IOP Publishing in Smart Materials and Structures
- Vol. 33 (2) , 025011
Flexural behaviour of cementitious composites embedded with 3D printed re-entrant chiral auxetic meshes
3D printed auxetic metamaterials can be used to make high performing cementitious composites to strengthen existing structures and elements due to their negative Poisson’s ratio behaviour and high energy absorbing characteristics. In this paper, three different re-entrant chiral auxetic (RCA) meshes of various cell geometries and orientations were developed by 3D printing them using poly-lactic acid (PLA) and thermoplastic polyurethane (TPU) filament. The developed meshes were tested under out-of-plane flexure to study their load carrying capacity, ductility and energy absorption characteristics, especially to characterise the best cell orientation. The horizontal cells provided enhanced load carrying and energy absorption characteristics for all three cell geometries for both materials. These RCA meshes were then embedded into low and high strength premix cement mortar matrices to develop auxetic cementitious composites (ACCs). In total, 42 ACC specimens were casted and tested under flexural loading. The results were studied in terms of their failure patterns, load-displacement responses, flexural capacities, ductility and energy absorption. The RCA meshes made of PLA filament showed limited capacity and energy absorption as compared to RCA meshes made of TPU filament due to extended flexibility and resilience provided by TPU meshes. The RCA meshes with a denser cell structure exhibited highest flexural capacity and effective energy absorption of 14 700 kJ m−2 for TPU-RCA mesh embedded into high strength cement mortar matrix. The results obtained in this study have enabled to understand the flexural behaviour of cementitious composites embedded with 3D printed auxetic lattices and to strengthen the existing structures.
- 17 January 2024
- Published by IOP Publishing in Smart Materials and Structures
- Vol. 33 (2) , 025011
Open AccessFlexural behaviour of cementitious composites embedded with 3D printed re-entrant chiral auxetic meshes
3D printed auxetic metamaterials can be used to make high performing cementitious composites to strengthen existing structures and elements due to their negative Poisson’s ratio behaviour and high energy absorbing characteristics. In this paper, three different re-entrant chiral auxetic (RCA) meshes of various cell geometries and orientations were developed by 3D printing them using poly-lactic acid (PLA) and thermoplastic polyurethane (TPU) filament. The developed meshes were tested under out-of-plane flexure to study their load carrying capacity, ductility and energy absorption characteristics, especially to characterise the best cell orientation. The horizontal cells provided enhanced load carrying and energy absorption characteristics for all three cell geometries for both materials. These RCA meshes were then embedded into low and high strength premix cement mortar matrices to develop auxetic cementitious composites (ACCs). In total, 42 ACC specimens were casted and tested under flexural loading. The results were studied in terms of their failure patterns, load-displacement responses, flexural capacities, ductility and energy absorption. The RCA meshes made of PLA filament showed limited capacity and energy absorption as compared to RCA meshes made of TPU filament due to extended flexibility and resilience provided by TPU meshes. The RCA meshes with a denser cell structure exhibited highest flexural capacity and effective energy absorption of 14 700 kJ m−2 for TPU-RCA mesh embedded into high strength cement mortar matrix. The results obtained in this study have enabled to understand the flexural behaviour of cementitious composites embedded with 3D printed auxetic lattices and to strengthen the existing structures.
- Open Access
- 20 October 2023
- Published by Elsevier in Engineering Structures
- Vol. 298
Out of-plane failure analysis of masonry walls subjected to hydrostatic and hydrodynamic loads induced by flash floods
- 20 October 2023
- Published by Elsevier in Engineering Structures
- Vol. 298
Open AccessOut of-plane failure analysis of masonry walls subjected to hydrostatic and hydrodynamic loads induced by flash floods
- Open Access
- 21 April 2023
- Published by Elsevier in Construction and Building Materials
- Vol. 384
Out-of-plane flexural behaviour of reinforced mortarless concrete block masonry: An experimental study
- 21 April 2023
- Published by Elsevier in Construction and Building Materials
- Vol. 384
Open AccessOut-of-plane flexural behaviour of reinforced mortarless concrete block masonry: An experimental study
- 21 January 2023
- Published by Elsevier in Journal of Building Engineering
- Vol. 66
In-plane and out-of-plane shear characteristics of reinforced mortarless concrete block masonry
- 21 January 2023
- Published by Elsevier in Journal of Building Engineering
- Vol. 66
In-plane and out-of-plane shear characteristics of reinforced mortarless concrete block masonry