Dan O'COnnell
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Dan O'COnnell has a total of 36 co-authors. Here are the top co-authors by number of shared publications:
- Colin Lyons
Tyndall National Institute, University College Cork, Dyke Parade, Cork, T12R5CP, Ireland
3 shared publications Alan Hydes
Tyndall National Institute, University College Cork 1 , Lee Maltings, Cork, Ireland
2 shared publicationsBrenda Long
School of Chemistry, University College Cork 3 , Cork, Ireland
2 shared publicationsBrendan Sheehan
Tyndall National Institute, University College Cork 1 , Lee Maltings, Cork, Ireland
2 shared publicationsChris Hatem
Applied Materials 7 , Gloucester, Massachusetts 01930, USA
2 shared publicationsGraeme Maxwell
Tyndall National Institute, University College Cork 1 , Lee Maltings, Cork, Ireland
2 shared publications
Latest Publications
- Open Access
- 14 July 2022
- Published by IOP Publishing in Nanotechnology
- Vol. 33 (40) , 405204
Direct-write formation of integrated bottom contacts to laser-induced graphene-like carbon
We report a simple, scalable two-step method for direct-write laser fabrication of 3D, porous graphene-like carbon electrodes from polyimide films with integrated contact plugs to underlying metal layers (Au or Ni). Irradiation at high average CO2 laser power (30 W) and low scan speed (∼18 mm s)−1 leads to formation of ‘keyhole’ contact plugs through local ablation of polyimide (initial thickness 17 μm) and graphitization of the plug perimeter wall. Top-surface laser-induced graphene (LIG) electrodes are then formed and connected to the plug by raster patterning at lower laser power (3.7 W) and higher scan speed (200 mm s)−1. Sheet resistance data (71 ± 15 Ω sq.)−1 indicates formation of high-quality surface LIG, consistent with Raman data which yield sharp first- and second-order peaks. We have also demonstrated that high-quality LIG requires a minimum initial polyimide thickness. Capacitance data measured between surface LIG electrodes and the buried metal film indicate a polyimide layer of thickness ∼7 μm remaining following laser processing. By contrast, laser graphitization of polyimide of initial thickness ∼8 μm yielded devices with large sheet resistance (>1 kΩ sq.)−1. Raman data also indicated significant disorder. Plug contact resistance values were calculated from analysis of transfer line measurement data for single- and multi-plug test structures. Contacts to buried nickel layers yielded lower plug resistances (1-plug: 158 ± 7 Ω , 4-plug: 31 ± 14 Ω) compared to contacts to buried gold (1-plug: 346 ± 37 Ω , 4-plug: 52 ± 3 Ω). Further reductions are expected for multi-plug structures with increased areal density. Proof-of-concept mm-scale LIG electrochemical devices with local contact plugs yielded rapid electron transfer kinetics (rate constant k 0 ∼ 0.017 cm s−1), comparable to values measured for exposed Au films (k 0 ∼0.023 cm s)−1. Our results highlight the potential for integration of LIG-based sensor electrodes with semiconductor or roll-to-roll manufacturing.
- 14 July 2022
- Published by IOP Publishing in Nanotechnology
- Vol. 33 (40) , 405204
Open AccessDirect-write formation of integrated bottom contacts to laser-induced graphene-like carbon
We report a simple, scalable two-step method for direct-write laser fabrication of 3D, porous graphene-like carbon electrodes from polyimide films with integrated contact plugs to underlying metal layers (Au or Ni). Irradiation at high average CO2 laser power (30 W) and low scan speed (∼18 mm s)−1 leads to formation of ‘keyhole’ contact plugs through local ablation of polyimide (initial thickness 17 μm) and graphitization of the plug perimeter wall. Top-surface laser-induced graphene (LIG) electrodes are then formed and connected to the plug by raster patterning at lower laser power (3.7 W) and higher scan speed (200 mm s)−1. Sheet resistance data (71 ± 15 Ω sq.)−1 indicates formation of high-quality surface LIG, consistent with Raman data which yield sharp first- and second-order peaks. We have also demonstrated that high-quality LIG requires a minimum initial polyimide thickness. Capacitance data measured between surface LIG electrodes and the buried metal film indicate a polyimide layer of thickness ∼7 μm remaining following laser processing. By contrast, laser graphitization of polyimide of initial thickness ∼8 μm yielded devices with large sheet resistance (>1 kΩ sq.)−1. Raman data also indicated significant disorder. Plug contact resistance values were calculated from analysis of transfer line measurement data for single- and multi-plug test structures. Contacts to buried nickel layers yielded lower plug resistances (1-plug: 158 ± 7 Ω , 4-plug: 31 ± 14 Ω) compared to contacts to buried gold (1-plug: 346 ± 37 Ω , 4-plug: 52 ± 3 Ω). Further reductions are expected for multi-plug structures with increased areal density. Proof-of-concept mm-scale LIG electrochemical devices with local contact plugs yielded rapid electron transfer kinetics (rate constant k 0 ∼ 0.017 cm s−1), comparable to values measured for exposed Au films (k 0 ∼0.023 cm s)−1. Our results highlight the potential for integration of LIG-based sensor electrodes with semiconductor or roll-to-roll manufacturing.
- 26 July 2018
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 124 (4) , 045703
AsH3 gas-phase ex situ doping 3D silicon structures
Dopant incorporation in Si can be done in situ during epitaxial growth, or ex situ for localised material modification from a variety of sources including ion, solid, liquid, or gas. Gas-phase doping has the advantage that it does not require a thin film deposition, it is more effective at entering tight spaces than a liquid, and it is less damaging and more conformal than a beam-line ion implant. In this work, we apply arsine (AsH3) gas at approximately atmospheric pressures in order to n-type dope three-dimensional (3D) Si device structures. It was observed that the gas-phase doping can be either corrosive or gentle to thin-body Si depending on the process conditions. Initial doping processes caused damage to the Si due to etching, but after process optimisation, the structural integrity of the Si nanostructures could be maintained successfully. Moreover, it was noted that evaluating doping processes entirely on planar Si surfaces can be misleading: processes which appear promising initially may not be transferrable to non-planar thin-body structures like fins or nanowires, due to unwanted Si etching. Overall, we found that gas-phase doping with AsH3 could provide >1020 cm−3 electrically active As concentrations. This high As incorporation makes gas-phase doping very attractive for future gate-all-around devices, where the space between features will decline with continued transistor scaling.
- 26 July 2018
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 124 (4) , 045703
AsH3 gas-phase ex situ doping 3D silicon structures
Dopant incorporation in Si can be done in situ during epitaxial growth, or ex situ for localised material modification from a variety of sources including ion, solid, liquid, or gas. Gas-phase doping has the advantage that it does not require a thin film deposition, it is more effective at entering tight spaces than a liquid, and it is less damaging and more conformal than a beam-line ion implant. In this work, we apply arsine (AsH3) gas at approximately atmospheric pressures in order to n-type dope three-dimensional (3D) Si device structures. It was observed that the gas-phase doping can be either corrosive or gentle to thin-body Si depending on the process conditions. Initial doping processes caused damage to the Si due to etching, but after process optimisation, the structural integrity of the Si nanostructures could be maintained successfully. Moreover, it was noted that evaluating doping processes entirely on planar Si surfaces can be misleading: processes which appear promising initially may not be transferrable to non-planar thin-body structures like fins or nanowires, due to unwanted Si etching. Overall, we found that gas-phase doping with AsH3 could provide >1020 cm−3 electrically active As concentrations. This high As incorporation makes gas-phase doping very attractive for future gate-all-around devices, where the space between features will decline with continued transistor scaling.
- 28 March 2018
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 123 (12) , 125701
Diagnosis of phosphorus monolayer doping in silicon based on nanowire electrical characterisation
The advent of high surface-to-volume ratio devices has necessitated a revised approach to parameter extraction and process evaluation in field-effect transistor technologies. In this work, active doping concentrations are extracted from the electrical analysis of Si nanowire devices with high surface-to-volume ratios. Nanowire resistance and Si resistivity are extracted, by first extracting and subtracting out the contact resistance. Resistivity (ρ) is selected as the benchmark parameter to compare different doping processes with each other. The impacts of nanowire diameter scaling to 10 nm and of nanowire spacing scaling to 2 cap in terms of lower Si resistivity and higher dopant activation, with dependencies on the nanowire width greater than on nanowire spacing. Limitations in ADP P monolayer doping with a SiO2 cap are due to the difficulties in dopant incorporation, as it is based on in-diffusion, and P atoms must overcome a potential barrier on the Si surface.
- 28 March 2018
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 123 (12) , 125701
Diagnosis of phosphorus monolayer doping in silicon based on nanowire electrical characterisation
The advent of high surface-to-volume ratio devices has necessitated a revised approach to parameter extraction and process evaluation in field-effect transistor technologies. In this work, active doping concentrations are extracted from the electrical analysis of Si nanowire devices with high surface-to-volume ratios. Nanowire resistance and Si resistivity are extracted, by first extracting and subtracting out the contact resistance. Resistivity (ρ) is selected as the benchmark parameter to compare different doping processes with each other. The impacts of nanowire diameter scaling to 10 nm and of nanowire spacing scaling to 2 cap in terms of lower Si resistivity and higher dopant activation, with dependencies on the nanowire width greater than on nanowire spacing. Limitations in ADP P monolayer doping with a SiO2 cap are due to the difficulties in dopant incorporation, as it is based on in-diffusion, and P atoms must overcome a potential barrier on the Si surface.
- 1 June 2011
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 0149645X,p. 1-4
Sub-millimeter Wave 183 GHz and 366 GHz MMIC membrane sub-harmonic mixers
The design, fabrication and testing of broadband fixed-tuned 183 GHz and 366 GHz sub-harmonic mixers is discussed. Two mixer circuits using planar Schottky diodes monolithically integrated with RF/LO and IF matching and filtering networks onto a 3.7 um thick GaAs membrane are presented. The mixers were designed and fabricated using a novel approach in post processing of commercial foundry wafers. The double sideband measurements at room temperature on the 183 GHz sub-harmonic mixer yielded conversion loss and noise temperature of 4.9 dB and 608 K, respectively. The measured double sideband conversion loss and noise temperature of the 366 GHz mixer were 6.9 dB and 1220 K, respectively. To the authors' knowledge these are the best published results for sub-harmonic MMIC membrane mixers at these frequencies.
- 1 June 2011
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 0149645X,p. 1-4
Sub-millimeter Wave 183 GHz and 366 GHz MMIC membrane sub-harmonic mixers
The design, fabrication and testing of broadband fixed-tuned 183 GHz and 366 GHz sub-harmonic mixers is discussed. Two mixer circuits using planar Schottky diodes monolithically integrated with RF/LO and IF matching and filtering networks onto a 3.7 um thick GaAs membrane are presented. The mixers were designed and fabricated using a novel approach in post processing of commercial foundry wafers. The double sideband measurements at room temperature on the 183 GHz sub-harmonic mixer yielded conversion loss and noise temperature of 4.9 dB and 608 K, respectively. The measured double sideband conversion loss and noise temperature of the 366 GHz mixer were 6.9 dB and 1220 K, respectively. To the authors' knowledge these are the best published results for sub-harmonic MMIC membrane mixers at these frequencies.