Hao Liu
Hao Liu has a total of 18 co-authors. Here are the top co-authors by number of shared publications:
- Matthew Ming-Fai Yuen
Department of Mechanical Engineering, Hong Kong University of Science and Technology, Hong Kong 999077, China
2 shared publications - Mingxuan Cao
School of Mechanical and Automation Engineering, Wuyi University, Jiangmen 529020, China
2 shared publications - Ying Wang
Department of Intelligent Manufacturing, Wuyi University, Jiangmen 529020, China
2 shared publications - Hua Yang
School of Advanced Manufacturing, Sun Yat-sen University, Shenzhen 518107, China
1 shared publication - Jianing Wu
School of Aeronautics and Astronautics, Sun Yat-sen University, Shenzhen 518107, China
1 shared publication - Jianquan Yao
Tianjin University
1 shared publication
Latest Publications
- Open Access
- 26 July 2024
- Published by MDPI AG in Biomimetics
- Vol. 9 (8) , 457
Swifts Form V-Shaped Wings While Dipping in Water to Fine-Tune Balance
Swifts, a distinctive avian cohort, have garnered widespread attention owing to their exceptional flight agility. While their aerial prowess is well documented, the challenge swifts encounter while imbibing water introduces an intriguing complexity. The act of water uptake potentially disrupts their flight equilibrium, yet the mechanisms enabling these birds to maintain stability during this process remain enigmatic. In this study, we employed high-speed videography to observe swifts’ water-drinking behavior. Notably, we observed that the swift adopts a dynamic V-shaped wing configuration during water immersion with the ability to modulate the V-shaped angle, thereby potentially fine-tuning their balance. To delve deeper, we utilized a three-dimensional laser scanner to meticulously construct a virtual 3D model of swifts, followed by computational fluid dynamics simulations to quantitatively assess the mechanical conditions during foraging. Our model indicates that the adoption of V-shaped wings, with a variable wing angle ranging from 30 to 60 degrees, serves to minimize residual torque, effectively mitigating potential flight instability. These findings not only enhance our comprehension of swifts’ flight adaptability but also hold promise for inspiring innovative, highly maneuverable next-generation unmanned aerial vehicles. This research thus transcends avian biology, offering valuable insights for engineering and aeronautics.
- 26 July 2024
- Published by MDPI AG in Biomimetics
- Vol. 9 (8) , 457
Open AccessSwifts Form V-Shaped Wings While Dipping in Water to Fine-Tune Balance
Swifts, a distinctive avian cohort, have garnered widespread attention owing to their exceptional flight agility. While their aerial prowess is well documented, the challenge swifts encounter while imbibing water introduces an intriguing complexity. The act of water uptake potentially disrupts their flight equilibrium, yet the mechanisms enabling these birds to maintain stability during this process remain enigmatic. In this study, we employed high-speed videography to observe swifts’ water-drinking behavior. Notably, we observed that the swift adopts a dynamic V-shaped wing configuration during water immersion with the ability to modulate the V-shaped angle, thereby potentially fine-tuning their balance. To delve deeper, we utilized a three-dimensional laser scanner to meticulously construct a virtual 3D model of swifts, followed by computational fluid dynamics simulations to quantitatively assess the mechanical conditions during foraging. Our model indicates that the adoption of V-shaped wings, with a variable wing angle ranging from 30 to 60 degrees, serves to minimize residual torque, effectively mitigating potential flight instability. These findings not only enhance our comprehension of swifts’ flight adaptability but also hold promise for inspiring innovative, highly maneuverable next-generation unmanned aerial vehicles. This research thus transcends avian biology, offering valuable insights for engineering and aeronautics.
- Open Access
- 25 November 2022
- Published by MDPI AG in Micromachines
- Vol. 13 (12) , 2072
The Effect of Geometric Parameters on Flow and Heat Transfer Characteristics of a Double-Layer Microchannel Heat Sink for High-Power Diode Laser
The effect of the geometric parameters on the flow and heat transfer characteristics of a double-layer U-shape microchannel heat sink (DL-MCHS) for a high-power diode laser was investigated in this work. FLUENT 19.2 based on the finite volume method was employed to analyze the flow and heat transfer performance of DL-MCHS. A single variable approach was used to fully research the impact of different parameters (the number of channels, the channel cross-sectional shape, and the aspect ratio) on the temperature distribution, pressure drop, and thermal resistance of the DL-MCHS. The rectangular DL-MCHS heat transfer performance and pressure drop significantly increased with the rise in the channel’s aspect ratio due to there being a larger wet perimeter and convective heat transfer area. By comparing the thermal resistance of the DL-MCHS at the same power consumption, it was found that the rectangular DL-MCHS with an aspect ratio in the range of 5.1180–6.389 had the best overall performance. With the same cross-sectional area and hydraulic diameter (AC = 0.36 mm, Dh = 0.417 mm), the thermal resistance of the trapezoidal microchannel heat sink was 32.14% and 42.42% lower than that of the triangular and rectangular ones, respectively, under the condition that the pumping power (Wpp) was 0.2 W. Additionally, the thermal resistance was reduced with the increment of the number of channels inside the DL-MCHS, but this would induce an increased pressure drop. Thus, the channel number has an optimal range, which is between 50 and 80 for the heat sinks in this study. Our study served as a simulation foundation for the semiconductor laser double-layer U-shaped MCHS optimization method using geometric parameters.
- 25 November 2022
- Published by MDPI AG in Micromachines
- Vol. 13 (12) , 2072
Open AccessThe Effect of Geometric Parameters on Flow and Heat Transfer Characteristics of a Double-Layer Microchannel Heat Sink for High-Power Diode Laser
The effect of the geometric parameters on the flow and heat transfer characteristics of a double-layer U-shape microchannel heat sink (DL-MCHS) for a high-power diode laser was investigated in this work. FLUENT 19.2 based on the finite volume method was employed to analyze the flow and heat transfer performance of DL-MCHS. A single variable approach was used to fully research the impact of different parameters (the number of channels, the channel cross-sectional shape, and the aspect ratio) on the temperature distribution, pressure drop, and thermal resistance of the DL-MCHS. The rectangular DL-MCHS heat transfer performance and pressure drop significantly increased with the rise in the channel’s aspect ratio due to there being a larger wet perimeter and convective heat transfer area. By comparing the thermal resistance of the DL-MCHS at the same power consumption, it was found that the rectangular DL-MCHS with an aspect ratio in the range of 5.1180–6.389 had the best overall performance. With the same cross-sectional area and hydraulic diameter (AC = 0.36 mm, Dh = 0.417 mm), the thermal resistance of the trapezoidal microchannel heat sink was 32.14% and 42.42% lower than that of the triangular and rectangular ones, respectively, under the condition that the pumping power (Wpp) was 0.2 W. Additionally, the thermal resistance was reduced with the increment of the number of channels inside the DL-MCHS, but this would induce an increased pressure drop. Thus, the channel number has an optimal range, which is between 50 and 80 for the heat sinks in this study. Our study served as a simulation foundation for the semiconductor laser double-layer U-shaped MCHS optimization method using geometric parameters.
- Open Access
Plasmonically Enhanced Colloidal Quantum Dot/Graphene Doped Polymer Random Lasers
An improvement in random lasers based on a colloidal quantum dot (QD)/graphene-doped polymer was observed and attributed to multiple light-scattering and graphene surface plasmon resonance. The emission characteristics of quantum dots doped with graphene oxide and reduced graphene oxide were compared. The QD/reduced graphene oxide hybrid exhibited a lower laser emission threshold (~460 μJ/cm2). The emission modes and thresholds were strongly dependent on both the graphene doping concentration and the external temperature. Decreased plasmon coupling was the primary reason for lower QD/graphene laser emission with increasing temperature. The optimum reduced graphene oxide concentration was 0.2 wt.%. This work provides a practical approach to optimizing the threshold and stability of random laser devices, with potential applications in displays, sensors, and anti-counterfeiting labels.
Open AccessPlasmonically Enhanced Colloidal Quantum Dot/Graphene Doped Polymer Random Lasers
An improvement in random lasers based on a colloidal quantum dot (QD)/graphene-doped polymer was observed and attributed to multiple light-scattering and graphene surface plasmon resonance. The emission characteristics of quantum dots doped with graphene oxide and reduced graphene oxide were compared. The QD/reduced graphene oxide hybrid exhibited a lower laser emission threshold (~460 μJ/cm2). The emission modes and thresholds were strongly dependent on both the graphene doping concentration and the external temperature. Decreased plasmon coupling was the primary reason for lower QD/graphene laser emission with increasing temperature. The optimum reduced graphene oxide concentration was 0.2 wt.%. This work provides a practical approach to optimizing the threshold and stability of random laser devices, with potential applications in displays, sensors, and anti-counterfeiting labels.