Hiralal Murlidhar Suryawanshi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Hiralal Murlidhar Suryawanshi has a total of 16 co-authors. Here are the top co-authors by number of shared publications:
- Dipesh Atkar
Department of Electrical Engineering, Visvesvaraya National Institute of Technology, Nagpur, India
2 shared publications - Pradyumn Chaturvedi
Department of Electrical Engineering, Visvesvaraya National Institute of Technology, Nagpur, India
2 shared publications - Pratik Nachankar
Electrical Engineering Department, Visvesvaraya National Institute of Technology, Nagpur, Maharashtra, India
2 shared publications - Vijaya Vardhan Reddy P.
Varroc Engineering LTD, Aurangabad, India
2 shared publications - Beeramangalla Lakshminarasaiah Narasimharaju
Professor, Department of Electrical Engineering, NIT Warangal
1 shared publication Ch. L. Narayana
Electrical Engineering Department, Visvesvaraya National Institute of Technology, Nagpur, India
1 shared publication
Latest Publications
- 5 November 2026
- Published by Wiley in International Journal of Circuit Theory and Applications
Non‐Conductive Inductive Power Transfer Charging Gun of Electric Vehicle
Electric vehicles are gaining importance as they are a clean and cheap mode of transportation. Conductive charging gun is used to charge most of the electric vehicles. If the charging gun is not connected properly or is loose, then there is a possibility that the gun becomes hot, so the thermal sensor of the charging gun stops charging, or in some conditions it is reason of catching fire in the electric vehicle. In this paper, a non‐conductive inductive power transfer charging gun is proposed to charge an electric vehicle. Proposed non‐conductive inductive power transfer charging gun solves all problem which comes during charging of EV from a conductive gun. The electric shock hazard and safety related issues are addressed by this topology. In an electric vehicle, isolation should be provided, but in the case of charging an electric vehicle using a non‐conductive inductive power transfer charging gun, transmitting and receiving coils provide isolation, so the isolation stage can be removed. The coupling coefficient between the coil and the self‐inductance of the coil is calculated with the help of FEM software. The hardware prototype results are shown to validate that the proposed 1.5 kW non‐conductive inductive power transfer charging gun of an electric vehicle is demonstrated to transfer 15 A DC current load at 100 V DC output voltage and is validated for effectiveness.
- 5 November 2026
- Published by Wiley in International Journal of Circuit Theory and Applications
Non‐Conductive Inductive Power Transfer Charging Gun of Electric Vehicle
Electric vehicles are gaining importance as they are a clean and cheap mode of transportation. Conductive charging gun is used to charge most of the electric vehicles. If the charging gun is not connected properly or is loose, then there is a possibility that the gun becomes hot, so the thermal sensor of the charging gun stops charging, or in some conditions it is reason of catching fire in the electric vehicle. In this paper, a non‐conductive inductive power transfer charging gun is proposed to charge an electric vehicle. Proposed non‐conductive inductive power transfer charging gun solves all problem which comes during charging of EV from a conductive gun. The electric shock hazard and safety related issues are addressed by this topology. In an electric vehicle, isolation should be provided, but in the case of charging an electric vehicle using a non‐conductive inductive power transfer charging gun, transmitting and receiving coils provide isolation, so the isolation stage can be removed. The coupling coefficient between the coil and the self‐inductance of the coil is calculated with the help of FEM software. The hardware prototype results are shown to validate that the proposed 1.5 kW non‐conductive inductive power transfer charging gun of an electric vehicle is demonstrated to transfer 15 A DC current load at 100 V DC output voltage and is validated for effectiveness.
- 6 July 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industry Applications
- Vol. 59 (6) , 6889-6899
Design of Interleaved Three-Phase DC Transformer With Ingenious Control for Modern Data Centers
Data centers have a pivotal role in the uprising era of industrial IoT and 6 G communication. However, sustainability objectives requisite effective energy utilization in data centers in view of high consumption rate. This article proposes an efficient, three-phase semi-converter aided 400 V/48 V DC Transformer (DCTx) for rack-level distribution in data center. The three-phase semi-converter configuration imparts three degrees of control for superior 48 V regulation. In further, the DCTx is equipped with proposed ingenious, load-adaptive control approach. For control efficacy, the proposed control incorporates all possible control variables to ensure effective output voltage control during steady and dynamic states. The experimental results of developed 1 kW prototype suggest the feasibility of the proposed DC Transformer and associated control approach for 400 V/48 V DC data center DC power distribution application.
- 6 July 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industry Applications
- Vol. 59 (6) , 6889-6899
Design of Interleaved Three-Phase DC Transformer With Ingenious Control for Modern Data Centers
Data centers have a pivotal role in the uprising era of industrial IoT and 6 G communication. However, sustainability objectives requisite effective energy utilization in data centers in view of high consumption rate. This article proposes an efficient, three-phase semi-converter aided 400 V/48 V DC Transformer (DCTx) for rack-level distribution in data center. The three-phase semi-converter configuration imparts three degrees of control for superior 48 V regulation. In further, the DCTx is equipped with proposed ingenious, load-adaptive control approach. For control efficacy, the proposed control incorporates all possible control variables to ensure effective output voltage control during steady and dynamic states. The experimental results of developed 1 kW prototype suggest the feasibility of the proposed DC Transformer and associated control approach for 400 V/48 V DC data center DC power distribution application.
- 9 January 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. 70 (8) , 7879-7890
A Three-Level Resonant DAB Converter Featuring Minimized Circulating Losses for EV Battery Charging
A three-level modified series–parallel bidirectional isolated dc–dc resonant converter (TL-MSPBRC) is proposed for electric vehicle (EV) battery charging. The converter's performance is enhanced for wide load conditions as the modified series–parallel resonant tank is formed by considering the parasitics in the transformer. The first-harmonic approximation (FHA) equivalent circuit model is employed to analyze the converter characteristics for the frequency modulation technique. This converter has high conversion efficiency in charging and discharging operations because of the soft-switching capability of the power switches in the primary and secondary bridges. In addition, low on -state resistance switches in the three-level primary bridge minimize the conduction losses. A 3.3-kW converter prototype with a battery voltage range of 230 $-$ 300-V is developed to validate the design method and the simulation results. The proposed converter has minimized circulating losses, good short-circuit protection, and excellent efficiency of 97.7% at the rated power level.
- 9 January 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. 70 (8) , 7879-7890
A Three-Level Resonant DAB Converter Featuring Minimized Circulating Losses for EV Battery Charging
A three-level modified series–parallel bidirectional isolated dc–dc resonant converter (TL-MSPBRC) is proposed for electric vehicle (EV) battery charging. The converter's performance is enhanced for wide load conditions as the modified series–parallel resonant tank is formed by considering the parasitics in the transformer. The first-harmonic approximation (FHA) equivalent circuit model is employed to analyze the converter characteristics for the frequency modulation technique. This converter has high conversion efficiency in charging and discharging operations because of the soft-switching capability of the power switches in the primary and secondary bridges. In addition, low on -state resistance switches in the three-level primary bridge minimize the conduction losses. A 3.3-kW converter prototype with a battery voltage range of 230 $-$ 300-V is developed to validate the design method and the simulation results. The proposed converter has minimized circulating losses, good short-circuit protection, and excellent efficiency of 97.7% at the rated power level.
- 18 October 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. 70 (9) , 9016-9024
Implementation of Dual Control Maximum Power Point Tracking-Based DC–DC Converter Fed Solar PV Power Application
This article presents an effective power extraction methodology from photovoltaic (PV) with a front end dc–dc Resonant converter with dual control. Usually, conventional dc–dc boost converter shows lower efficiency and extra components for soft-switching. Furthermore, converter power transfer efficiency for PV integration is limited. Hence, to address these challenges this article investigates an isolated dc–dc resonant converter with proposed control to attain wider voltage regulation with maximized PV power generation. In addition, this converter can achieve zero-voltage switching under wider operating loads. The proposed control method improves the efficiency even under light load condition without effecting digital-signal-processor resolution, along with a simple pertub and observe maximum power point PI control approach. A 2.2-kW prototype is built and operated to interface PV system and to verify the performance over entire load. The peak efficiency of the converter is found to be 98.7% at (1.1-kW) 50% of the full load.
- 18 October 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. 70 (9) , 9016-9024
Implementation of Dual Control Maximum Power Point Tracking-Based DC–DC Converter Fed Solar PV Power Application
This article presents an effective power extraction methodology from photovoltaic (PV) with a front end dc–dc Resonant converter with dual control. Usually, conventional dc–dc boost converter shows lower efficiency and extra components for soft-switching. Furthermore, converter power transfer efficiency for PV integration is limited. Hence, to address these challenges this article investigates an isolated dc–dc resonant converter with proposed control to attain wider voltage regulation with maximized PV power generation. In addition, this converter can achieve zero-voltage switching under wider operating loads. The proposed control method improves the efficiency even under light load condition without effecting digital-signal-processor resolution, along with a simple pertub and observe maximum power point PI control approach. A 2.2-kW prototype is built and operated to interface PV system and to verify the performance over entire load. The peak efficiency of the converter is found to be 98.7% at (1.1-kW) 50% of the full load.
- 10 August 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. 70 (6) , 5771-5783
Adaptive Control Algorithm for Two-Stage Integrated DC Transformer in DC Microgrid Applications
This article presents the two-stage integrated DC transformer (TSDCT) for DC microgrid (MG) applications based on the adaptive control algorithm (ACA). The prevailing control methods and design constraints employed in the DC transformer do not consider the influence of the circuit's structural elements with their parasitic components on its performance. Consequently, it devalues the control variables that fail to achieve indispensable control features in the DC MG network. Therefore, the proposed ACA is employed in the TSDCT, which improves the performance of TSDCT in comparison to the other control techniques in the DC MG network. The proposed ACA includes the effect of the resonant tank circuit's parameters and converter's structural elements. Thereby, it defines the design constraints that significantly improve the performance of TSDCT in terms of efficiency and a wide range of voltage regulation at different buses. The detailed modeling and analysis are carried out at each stage to describe the principle and evolution of critical components involved in the ACA. Further, the control to output transfer functions is determined toward the implementation of the proposed ACA in the TSDCT. As a result, it exhibits voltage regulation in a wide range, soft-switching operation, high control resolution, and better performance under different operating conditions. Finally, a 4-kW laboratory platform is built, and test results validate the performance of the proposed TSDCT based on the proposed ACA for DC MG applications.
- 10 August 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. 70 (6) , 5771-5783
Adaptive Control Algorithm for Two-Stage Integrated DC Transformer in DC Microgrid Applications
This article presents the two-stage integrated DC transformer (TSDCT) for DC microgrid (MG) applications based on the adaptive control algorithm (ACA). The prevailing control methods and design constraints employed in the DC transformer do not consider the influence of the circuit's structural elements with their parasitic components on its performance. Consequently, it devalues the control variables that fail to achieve indispensable control features in the DC MG network. Therefore, the proposed ACA is employed in the TSDCT, which improves the performance of TSDCT in comparison to the other control techniques in the DC MG network. The proposed ACA includes the effect of the resonant tank circuit's parameters and converter's structural elements. Thereby, it defines the design constraints that significantly improve the performance of TSDCT in terms of efficiency and a wide range of voltage regulation at different buses. The detailed modeling and analysis are carried out at each stage to describe the principle and evolution of critical components involved in the ACA. Further, the control to output transfer functions is determined toward the implementation of the proposed ACA in the TSDCT. As a result, it exhibits voltage regulation in a wide range, soft-switching operation, high control resolution, and better performance under different operating conditions. Finally, a 4-kW laboratory platform is built, and test results validate the performance of the proposed TSDCT based on the proposed ACA for DC MG applications.
- 18 August 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems II: Express Briefs
- Vol. 69 (3) , 1287-1291
A Quintupler Boost High Conversion Gain Soft-Switched Converter for DC Microgrid
This study proposes a high conversion gain soft-switching quintupler boost non-isolated converter for DC microgrid. By inclusion of quintupler rectifier and coupled inductor with reduced duty cycle, high voltage gain is obtained. The leakage energy of coupled inductor is recycled through an auxiliary switch and the output capacitor improves further boost. Due to the active clamp and this recycled leakage energy, huge inductive voltage spikes across MOSFETs are alleviated and also, stress is reduced. Hence, low voltage rating (low Rds(ON)) switches can be utilized and minimize conduction losses. In addition, this clamp enables zero-voltage switching (ZVS) for both the MOSFETs, even at light loads. Quintupler multiplier rectifier reduces the voltage stress across diodes. This, in turn, reduces reverse recovery losses for multiplier diodes. Further, the coupled inductor leakage inductance in series with diodes provides for the snubbing effect to alleviate voltage spikes across quintupler diodes. Thus, the overall diode voltage rating reduces. This improves power density and improves the overall efficiency of the converter. Finally, a 400W prototype operates at 100kHz is developed to validate the converter performance. The measured peak efficiency is 96.43%.
- 18 August 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems II: Express Briefs
- Vol. 69 (3) , 1287-1291
A Quintupler Boost High Conversion Gain Soft-Switched Converter for DC Microgrid
This study proposes a high conversion gain soft-switching quintupler boost non-isolated converter for DC microgrid. By inclusion of quintupler rectifier and coupled inductor with reduced duty cycle, high voltage gain is obtained. The leakage energy of coupled inductor is recycled through an auxiliary switch and the output capacitor improves further boost. Due to the active clamp and this recycled leakage energy, huge inductive voltage spikes across MOSFETs are alleviated and also, stress is reduced. Hence, low voltage rating (low Rds(ON)) switches can be utilized and minimize conduction losses. In addition, this clamp enables zero-voltage switching (ZVS) for both the MOSFETs, even at light loads. Quintupler multiplier rectifier reduces the voltage stress across diodes. This, in turn, reduces reverse recovery losses for multiplier diodes. Further, the coupled inductor leakage inductance in series with diodes provides for the snubbing effect to alleviate voltage spikes across quintupler diodes. Thus, the overall diode voltage rating reduces. This improves power density and improves the overall efficiency of the converter. Finally, a 400W prototype operates at 100kHz is developed to validate the converter performance. The measured peak efficiency is 96.43%.
- Open Access
- 1 October 2018
- Published by MDPI AG in Preprints.org
TRIPLE HYBRID CONTROLLED DC-DC RESONANT CONVERTER TO INTERFACE RENEWABLE ENERGY SYSTEM WITH DC GRID
This paper presents a programmable triple hybrid controller for DC-DC resonant converter which provides excellent DC grid voltage regulation when input voltage from renewable sources is reduced. The proposed control also exhibits superior performance in terms of conversion efficiency and soft switching of all the switches from rated load to very light load. In the triple hybrid controller, duty cycle modulation, switching frequency modulation and phase shift modulation are simultaneously adjusted in order to maintain constant DC bus voltage and maintain zero voltage switching (ZVS). The third control variable i.e. phase shift between two active bridges regulates output voltage when input voltage is varied. So, the converter with proposed controller can act as a smart power electronic interface between renewable energy resources and DC grid. The experimental and simulation results of the triple hybrid control for resonant converter tested on a 3kW with 100 kHz switching frequency are presented for an input voltage range of 250V-180V to validate the functionality of the proposed control.
- 1 October 2018
- Published by MDPI AG in Preprints.org
Open AccessTRIPLE HYBRID CONTROLLED DC-DC RESONANT CONVERTER TO INTERFACE RENEWABLE ENERGY SYSTEM WITH DC GRID
This paper presents a programmable triple hybrid controller for DC-DC resonant converter which provides excellent DC grid voltage regulation when input voltage from renewable sources is reduced. The proposed control also exhibits superior performance in terms of conversion efficiency and soft switching of all the switches from rated load to very light load. In the triple hybrid controller, duty cycle modulation, switching frequency modulation and phase shift modulation are simultaneously adjusted in order to maintain constant DC bus voltage and maintain zero voltage switching (ZVS). The third control variable i.e. phase shift between two active bridges regulates output voltage when input voltage is varied. So, the converter with proposed controller can act as a smart power electronic interface between renewable energy resources and DC grid. The experimental and simulation results of the triple hybrid control for resonant converter tested on a 3kW with 100 kHz switching frequency are presented for an input voltage range of 250V-180V to validate the functionality of the proposed control.