Xiaotian Wang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Xiaotian Wang has a total of 10 co-authors. Here are the top co-authors by number of shared publications:
- Chengjie Wang
Marine Engineering College, Dalian Maritime University, Dalian, China
3 shared publications - Chenzhao Bai
College of Marine Engineering, Dalian Maritime University, Dalian 116026, China
3 shared publications - Hongpeng Zhang
Dalian Maritime University
3 shared publications - Lebile Ilerioluwa
School of Marine Engineering, Dalian Maritime University, Dalian 116026, China
3 shared publications - Guobin Li
Marine Engineering College, Dalian Maritime University, Dalian 116026, China
2 shared publications - Wei Li
Dalian Maritime University
2 shared publications
Latest Publications
- 1 March 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Instrumentation and Measurement
- Vol. 71 (00189456) , 1-10
A Multi-Parameter Microfluidic Particle Sensor Based on Permalloy for High Sensitivity
Technologies for particle detection in lubricating or hydraulic oil are essential in mechanical industries to avoid constant machinery failure. The existing technologies utilize offline or online methods. Some of the online methods either have weak sensitivity or can only detect one type of particle. This article presents a highly sensitive, multi-parameter sensor for detecting various particles in hydraulic oil. This design takes advantage of high magnetic permeability and shielding efficiency of permalloy, placed behind dual opposite planar coils with a straight microchannel structure to improve the sensitivity of the sensor. The design includes both an inductive mode sensor, which can detect and distinguish ferromagnetic and nonferromagnetic metallic particles, and a capacitive mode sensor, which can detect and distinguish air bubbles and water droplets. Comparative COMSOL simulation and experiment were used to investigate the effect of permalloy and the results show that the sensor with permalloy has higher sensitivity compared to the sensor without permalloy. The sensor with permalloy successfully detected 15- $\mu \text{m}$ iron particle, 55- $\mu \text{m}$ copper particle, 75- $\mu \text{m}$ water droplet, and 95- $\mu \text{m}$ air bubble. This research shows the application of permalloy in the sensitivity improvement of microfluidic sensors.
- 1 March 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Instrumentation and Measurement
- Vol. 71 (00189456) , 1-10
A Multi-Parameter Microfluidic Particle Sensor Based on Permalloy for High Sensitivity
Technologies for particle detection in lubricating or hydraulic oil are essential in mechanical industries to avoid constant machinery failure. The existing technologies utilize offline or online methods. Some of the online methods either have weak sensitivity or can only detect one type of particle. This article presents a highly sensitive, multi-parameter sensor for detecting various particles in hydraulic oil. This design takes advantage of high magnetic permeability and shielding efficiency of permalloy, placed behind dual opposite planar coils with a straight microchannel structure to improve the sensitivity of the sensor. The design includes both an inductive mode sensor, which can detect and distinguish ferromagnetic and nonferromagnetic metallic particles, and a capacitive mode sensor, which can detect and distinguish air bubbles and water droplets. Comparative COMSOL simulation and experiment were used to investigate the effect of permalloy and the results show that the sensor with permalloy has higher sensitivity compared to the sensor without permalloy. The sensor with permalloy successfully detected 15- $\mu \text{m}$ iron particle, 55- $\mu \text{m}$ copper particle, 75- $\mu \text{m}$ water droplet, and 95- $\mu \text{m}$ air bubble. This research shows the application of permalloy in the sensitivity improvement of microfluidic sensors.
- Open Access
Research on High Sensitivity Oil Debris Detection Sensor Using High Magnetic Permeability Material and Coil Mutual Inductance
Metallic contaminants (solid) are generated by friction pair, causing wear of equipment by enters the lubricating system. This poses a great potential threat to the normal operation of such machines. The timely analysis and detection of debris can lead to the avoidance of mechanical failures. Abnormal wear in machinery may produce debris exceeding 10 μm. The traditional inductance detection method has low sensitivity and cannot meet the actual detection requirements. To boost the sensitivity of the inductance sensor, the mutual inductance of coils and the strong magnetic conductivity of permalloy was utilized to design a high sensitivity inductance sensor for the detection of debris in lubricating oil. This design was able to detect 10–15 μm iron particles and 65–70 μm copper particles in the oil. The experimental results illustrate that low-frequency excitation is the best for detecting ferromagnetic particles, while high-frequency excitation has the best effect for detecting non-ferromagnetic particles. This paper demonstrates the significant advantages of coil mutual inductance, and strong magnetic conductivity of permalloy in improving the detection sensitivity of oil debris sensors. This will provide technical support for wear detection in mechanical equipment and fault diagnosis.
Open AccessResearch on High Sensitivity Oil Debris Detection Sensor Using High Magnetic Permeability Material and Coil Mutual Inductance
Metallic contaminants (solid) are generated by friction pair, causing wear of equipment by enters the lubricating system. This poses a great potential threat to the normal operation of such machines. The timely analysis and detection of debris can lead to the avoidance of mechanical failures. Abnormal wear in machinery may produce debris exceeding 10 μm. The traditional inductance detection method has low sensitivity and cannot meet the actual detection requirements. To boost the sensitivity of the inductance sensor, the mutual inductance of coils and the strong magnetic conductivity of permalloy was utilized to design a high sensitivity inductance sensor for the detection of debris in lubricating oil. This design was able to detect 10–15 μm iron particles and 65–70 μm copper particles in the oil. The experimental results illustrate that low-frequency excitation is the best for detecting ferromagnetic particles, while high-frequency excitation has the best effect for detecting non-ferromagnetic particles. This paper demonstrates the significant advantages of coil mutual inductance, and strong magnetic conductivity of permalloy in improving the detection sensitivity of oil debris sensors. This will provide technical support for wear detection in mechanical equipment and fault diagnosis.
- Open Access
- 30 May 2021
- Published by MDPI AG in Micromachines
- Vol. 12 (6) , 638
Design and Research of Inductive Oil Pollutant Detection Sensor Based on High Gradient Magnetic Field Structure
An inductive oil pollutant detection sensor based on a high-gradient magnetic field structure is designed in this paper, which is mainly used for online detection and fault analysis of pollutants in hydraulic and lubricating oil systems. The innovation of the sensor is based on the inductance detection method. Permalloy is embedded in the sensing region of the sensor, so that the detection area generates a high gradient magnetic field to enhance the detection accuracy of the sensor. Compared with traditional inductive sensors, the sensor has a significant improvement in detection accuracy, and the addition of permalloy greatly improves the stability of the sensor’s detection unit structure. The article theoretically analyzes the working principle of the sensor, optimizes the design parameters and structure of the sensor through simulation, determines the best permalloy parameters, and establishes an experimental system for verification. Experimental results show that when a piece of permalloy is added to the sensing unit, the signal-to-noise ratio (SNR) of iron particles is increased by more than 20%, and the signal-to-noise ratio of copper particles is increased by more than 70%. When two pieces of permalloy are added, the signal-to-noise ratio for iron particles is increased by more than 70%, and the SNR for copper particles is increased several times. This method raises the lower limit of detection for ferromagnetic metal particles to 20 μm, and the lower limit for detection of non-ferromagnetic metal particles to 80 μm, which is the higher detection accuracy of the planar coil sensors. This paper provides a new and faster online method for pollutant detection in oil, which is of great significance for diagnosing and monitoring the health of oil in mechanical systems.
- 30 May 2021
- Published by MDPI AG in Micromachines
- Vol. 12 (6) , 638
Open AccessDesign and Research of Inductive Oil Pollutant Detection Sensor Based on High Gradient Magnetic Field Structure
An inductive oil pollutant detection sensor based on a high-gradient magnetic field structure is designed in this paper, which is mainly used for online detection and fault analysis of pollutants in hydraulic and lubricating oil systems. The innovation of the sensor is based on the inductance detection method. Permalloy is embedded in the sensing region of the sensor, so that the detection area generates a high gradient magnetic field to enhance the detection accuracy of the sensor. Compared with traditional inductive sensors, the sensor has a significant improvement in detection accuracy, and the addition of permalloy greatly improves the stability of the sensor’s detection unit structure. The article theoretically analyzes the working principle of the sensor, optimizes the design parameters and structure of the sensor through simulation, determines the best permalloy parameters, and establishes an experimental system for verification. Experimental results show that when a piece of permalloy is added to the sensing unit, the signal-to-noise ratio (SNR) of iron particles is increased by more than 20%, and the signal-to-noise ratio of copper particles is increased by more than 70%. When two pieces of permalloy are added, the signal-to-noise ratio for iron particles is increased by more than 70%, and the SNR for copper particles is increased several times. This method raises the lower limit of detection for ferromagnetic metal particles to 20 μm, and the lower limit for detection of non-ferromagnetic metal particles to 80 μm, which is the higher detection accuracy of the planar coil sensors. This paper provides a new and faster online method for pollutant detection in oil, which is of great significance for diagnosing and monitoring the health of oil in mechanical systems.