Mabrouk Ouederni
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Mabrouk Ouederni has a total of 21 co-authors. Here are the top co-authors by number of shared publications:
- Igor Krupa
Center for Advanced Materials, Qatar University, Doha, Qatar
5 shared publications - Anton Popelka
Center for Advanced Materials, Qatar University, Doha, Qatar
4 shared publications - Patrik Sobolčiak
Center for Advanced Materials, Qatar University, Doha P.O. Box 2713, Qatar
2 shared publications - Senthil Kumar Krishnamoorthy
Product Development & Innovation, Qatar Petrochemical Company (QAPCO), Doha P.O. Box 756, Qatar
2 shared publications - Antonín Minařík
Department of Physics and Materials Engineering, Faculty of Technology, Tomas Bata University in Zlín, Vavrečkova 5669, 760 01 Zlin, Czech Republic
1 shared publication - Aya E. Abusrafa
Center for Advanced Materials, Qatar University, P.O. Box 2713 Doha, Qatar
1 shared publication
Latest Publications
- Open Access
- 1 June 2025
- Published by KEAI Publishing in Energy and Built Environment
- Vol. 6 (3) , 455-465
Thermal energy storage materials designed from recycled Tetra Pak waste and paraffin waxes with enhanced photothermal conversion efficiencies
- 1 June 2025
- Published by KEAI Publishing in Energy and Built Environment
- Vol. 6 (3) , 455-465
Open AccessThermal energy storage materials designed from recycled Tetra Pak waste and paraffin waxes with enhanced photothermal conversion efficiencies
- Open Access
An Adhesion Improvement of Low-Density Polyethylene to Aluminum through Modification with Functionalized Polymers
An interfacial adhesion improvement between low-density polyethylene (LDPE) and aluminum (Al) foil is an important challenge in designing multilayered packaging (TetraPak packaging type) due to insufficient inherent adhesion between both untreated materials. Therefore, extra adhesive layers are often used. The hydrophobic character of LDPE is responsible for poor adhesion to Al and can result in delamination. This study deals with the comparative study of the bulk modification of LDPE with various commercially available adhesive promoters with different chemical compositions to increase LDPE’s adhesive characteristics and ensure good adhesion in LDPE/Al laminates. A copolymer of ethylene and methacrylic acid; a terpolymer of ethylene, maleic anhydride, and acrylic ester; or maleated polyethylene (PE) were used as adhesive promoters, and their effect on adhesion improvement of LDPE to Al was investigated. The best adhesion improvement was observed in LDPE-modified samples with maleated PE, while 0.1 wt.% additive content significantly increased peel resistance (from zero to 105 N/m). An additional increase in additive content (0.5 wt.%) in LDPE led to stronger adhesion forces than the cohesion forces in Al foil. Adding 0.5 wt.% of maleated PE into LDPE improved the LDPE/Al laminates’ adhesion and can be applied in multilayered lamination applications.
Open AccessAn Adhesion Improvement of Low-Density Polyethylene to Aluminum through Modification with Functionalized Polymers
An interfacial adhesion improvement between low-density polyethylene (LDPE) and aluminum (Al) foil is an important challenge in designing multilayered packaging (TetraPak packaging type) due to insufficient inherent adhesion between both untreated materials. Therefore, extra adhesive layers are often used. The hydrophobic character of LDPE is responsible for poor adhesion to Al and can result in delamination. This study deals with the comparative study of the bulk modification of LDPE with various commercially available adhesive promoters with different chemical compositions to increase LDPE’s adhesive characteristics and ensure good adhesion in LDPE/Al laminates. A copolymer of ethylene and methacrylic acid; a terpolymer of ethylene, maleic anhydride, and acrylic ester; or maleated polyethylene (PE) were used as adhesive promoters, and their effect on adhesion improvement of LDPE to Al was investigated. The best adhesion improvement was observed in LDPE-modified samples with maleated PE, while 0.1 wt.% additive content significantly increased peel resistance (from zero to 105 N/m). An additional increase in additive content (0.5 wt.%) in LDPE led to stronger adhesion forces than the cohesion forces in Al foil. Adding 0.5 wt.% of maleated PE into LDPE improved the LDPE/Al laminates’ adhesion and can be applied in multilayered lamination applications.
- 1 June 2022
- Published by American Society of Civil Engineers (ASCE) in Journal of Materials in Civil Engineering
- Vol. 34 (6) , 04022081
Nanostructural and Nanomechanical Properties of LDPE-Modified Binders
The main objective of this study is to explore the effects of various asphalt binder modifiers, including styrene–butadiene–styrene (SBS), elemental sulfur, reactive ethylene terpolymer (Elvaloy), and polyphosphoric acid (PPA) polymers on the nanostructural and nanomechanical (elastic and viscoelastic) properties of low-density polyethylene (LDPE)-modified binders. The study also aims to investigate the effect of aging on the nanoproperties of such blends. To this end, we used the PeakForce quantitative nanomechanical mapping (PFQNM) test and the nanoscale dynamic mechanical analysis (nDMA) test by means of atomic force microscopy. We further utilized the nanoscale results to better understand and interpret the bulk scale properties obtained using the dynamic shear rheometer (DSR). The nDMA results indicated an increase in stiffness and an enhancement in the elastic behavior of the blends after modification. Moreover, the blends exhibited a stiffer and more elastic behavior at the nanoscale when compared with the bulk DSR test results. Using Elvaloy and Elvaloy+PPA greatly enhanced the bond between LDPE and the binder. Both blends also showed resistance to heat-induced polymer separation and aging. Furthermore, the addition of SBS+sulfur enhanced LDPE dispersion within the binder. It was demonstrated that the use of elemental sulfur showed high efficacy in stabilizing LDPE-modified binders by inducing physical interaction between LDPE and the binder. Lastly, we concluded that the nanoscale measurements are very useful in understanding the local interactions, explaining the main aspects of the response at the bulk scale, and in the design of asphalt blends with improved properties.
- 1 June 2022
- Published by American Society of Civil Engineers (ASCE) in Journal of Materials in Civil Engineering
- Vol. 34 (6) , 04022081
Nanostructural and Nanomechanical Properties of LDPE-Modified Binders
The main objective of this study is to explore the effects of various asphalt binder modifiers, including styrene–butadiene–styrene (SBS), elemental sulfur, reactive ethylene terpolymer (Elvaloy), and polyphosphoric acid (PPA) polymers on the nanostructural and nanomechanical (elastic and viscoelastic) properties of low-density polyethylene (LDPE)-modified binders. The study also aims to investigate the effect of aging on the nanoproperties of such blends. To this end, we used the PeakForce quantitative nanomechanical mapping (PFQNM) test and the nanoscale dynamic mechanical analysis (nDMA) test by means of atomic force microscopy. We further utilized the nanoscale results to better understand and interpret the bulk scale properties obtained using the dynamic shear rheometer (DSR). The nDMA results indicated an increase in stiffness and an enhancement in the elastic behavior of the blends after modification. Moreover, the blends exhibited a stiffer and more elastic behavior at the nanoscale when compared with the bulk DSR test results. Using Elvaloy and Elvaloy+PPA greatly enhanced the bond between LDPE and the binder. Both blends also showed resistance to heat-induced polymer separation and aging. Furthermore, the addition of SBS+sulfur enhanced LDPE dispersion within the binder. It was demonstrated that the use of elemental sulfur showed high efficacy in stabilizing LDPE-modified binders by inducing physical interaction between LDPE and the binder. Lastly, we concluded that the nanoscale measurements are very useful in understanding the local interactions, explaining the main aspects of the response at the bulk scale, and in the design of asphalt blends with improved properties.
- Open Access
Foamed Phase Change Materials Based on Recycled Polyethylene/Paraffin Wax Blends
Foamed phase-change materials (FPCMs) were prepared using recycled linear low-density polyethylene (LLDPE) blended with 30 wt.% of paraffin wax (PW) and foamed by 1,1′-azobiscarbamide. The protection of pores’ collapse during foaming process was insured through chemical cross-linking by organic peroxide prior foaming. This work represents one of very few attempts for a preparation of polymeric phase change foams without a use of micro-encapsulated phase change component leading to the enhancement of the real PCM component (PW) within a final product. The porous structure of fabricated foams was analyzed using micro-computed tomography, and direct observation, and reconstruction of the internal structure was investigated. The porosity of FPCMs was about 85–87 vol.% and resulting thermal conductivity 0.054–0.086 W/m·K. Differential Scanning Calorimetry was used to determine the specific enthalpies of melting (22.4–25.1 J/g) what is the latent heat of materials utilized during a heat absorption. A stability of samples during 10 heating/cooling cycles was demonstrated. The phase change changes were also investigated using the dynamic mechanical analysis from 0° to 65 °C during the 10 cycles, and the mechanical stability of the system and phase-change transition were clearly confirmed, as proved by DSC. Leaching test revealed a long-term release of PW (around 7% of its original content) from samples which were long term stored at temperatures over PW melting point. This is the usual problem concerning polymer/wax blends. The most common, industrially feasible solution is a lamination of products, for instance by aluminum foils. Finally, the measurement of the heat flow simulating the real conditions shows that samples containing PW decrease the energy passing through the sample from 68.56 to 34.88 kJ·m−2. In this respect, FPCMs provide very effective double functionality, firstly common thermal insulators, and second, as the heat absorbers acting through melting of the PW and absorbing the excessive thermal energy during melting. This improves the heat protection of buildings and reduces temperature fluctuations within indoor spaces.
Open AccessFoamed Phase Change Materials Based on Recycled Polyethylene/Paraffin Wax Blends
Foamed phase-change materials (FPCMs) were prepared using recycled linear low-density polyethylene (LLDPE) blended with 30 wt.% of paraffin wax (PW) and foamed by 1,1′-azobiscarbamide. The protection of pores’ collapse during foaming process was insured through chemical cross-linking by organic peroxide prior foaming. This work represents one of very few attempts for a preparation of polymeric phase change foams without a use of micro-encapsulated phase change component leading to the enhancement of the real PCM component (PW) within a final product. The porous structure of fabricated foams was analyzed using micro-computed tomography, and direct observation, and reconstruction of the internal structure was investigated. The porosity of FPCMs was about 85–87 vol.% and resulting thermal conductivity 0.054–0.086 W/m·K. Differential Scanning Calorimetry was used to determine the specific enthalpies of melting (22.4–25.1 J/g) what is the latent heat of materials utilized during a heat absorption. A stability of samples during 10 heating/cooling cycles was demonstrated. The phase change changes were also investigated using the dynamic mechanical analysis from 0° to 65 °C during the 10 cycles, and the mechanical stability of the system and phase-change transition were clearly confirmed, as proved by DSC. Leaching test revealed a long-term release of PW (around 7% of its original content) from samples which were long term stored at temperatures over PW melting point. This is the usual problem concerning polymer/wax blends. The most common, industrially feasible solution is a lamination of products, for instance by aluminum foils. Finally, the measurement of the heat flow simulating the real conditions shows that samples containing PW decrease the energy passing through the sample from 68.56 to 34.88 kJ·m−2. In this respect, FPCMs provide very effective double functionality, firstly common thermal insulators, and second, as the heat absorbers acting through melting of the PW and absorbing the excessive thermal energy during melting. This improves the heat protection of buildings and reduces temperature fluctuations within indoor spaces.
- Open Access
Enhancement of Adhesion Characteristics of Low-Density Polyethylene Using Atmospheric Plasma Initiated-Grafting of Polyethylene Glycol
The low-density polyethylene/aluminum (LDPE/Al) joint in Tetra Pak provides stability and strength to food packaging, ensures protection against outside moisture, and maintains the nutritional values and flavors of food without the need for additives in the food products. However, a poor adhesion of LDPE to Al, due to its non-polar surface, is a limiting factor and extra polymeric interlayers or surface treatment is required. Plasma-assisted grafting of the LDPE surface with different molecular weight compounds of polyethylene glycol (PEG) was used to improve LDPE/Al adhesion. It was found that this surface modification contributed to significantly improve the wettability of the LDPE surface, as was confirmed by contact angle measurements. The chemical composition changes after plasma treatment and modification process were observed by X-ray photoelectron spectroscopy (XPS) and Fourier transform infrared spectroscopy (FTIR). A surface morphology was analyzed by scanning electron microscopy (SEM) and atomic force microscopy (AFM). Adhesion characteristics of LDPE/Al adhesive joints were analyzed by the peel tests. The most significant adhesion improvement of the PEG modified LDPE surface was achieved using 10.0 wt.% aqueous (6000 M) PEG solution, while the peel resistance increased by approximately 54 times in comparison with untreated LDPE.
Open AccessEnhancement of Adhesion Characteristics of Low-Density Polyethylene Using Atmospheric Plasma Initiated-Grafting of Polyethylene Glycol
The low-density polyethylene/aluminum (LDPE/Al) joint in Tetra Pak provides stability and strength to food packaging, ensures protection against outside moisture, and maintains the nutritional values and flavors of food without the need for additives in the food products. However, a poor adhesion of LDPE to Al, due to its non-polar surface, is a limiting factor and extra polymeric interlayers or surface treatment is required. Plasma-assisted grafting of the LDPE surface with different molecular weight compounds of polyethylene glycol (PEG) was used to improve LDPE/Al adhesion. It was found that this surface modification contributed to significantly improve the wettability of the LDPE surface, as was confirmed by contact angle measurements. The chemical composition changes after plasma treatment and modification process were observed by X-ray photoelectron spectroscopy (XPS) and Fourier transform infrared spectroscopy (FTIR). A surface morphology was analyzed by scanning electron microscopy (SEM) and atomic force microscopy (AFM). Adhesion characteristics of LDPE/Al adhesive joints were analyzed by the peel tests. The most significant adhesion improvement of the PEG modified LDPE surface was achieved using 10.0 wt.% aqueous (6000 M) PEG solution, while the peel resistance increased by approximately 54 times in comparison with untreated LDPE.
- Open Access
Recycled Polyethylene/Paraffin Wax/Expanded Graphite Based Heat Absorbers for Thermal Energy Storage: An Artificial Aging Study
An artificial aging study of novel heat absorbers based on phase change materials (PCMs) prepared from recycled high-density polyethylene (HDPE), paraffin wax (PW), and expanded graphite (EG) was investigated. The optimal composition of PCMs contained 40 wt% HDPE, whereas the paraffin wax content ranged from 40 to 60 wt% and the expanded graphite content ranged from 5 to 15 wt%. PCMs were artificially aged through exposure to UV irradiation, enhanced temperature, and humidity. It was clearly demonstrated that the addition of EG to PCMs led to the suppression of PW leakage and improved the photooxidation stability of the PCMs during the aging process. The best performance was achieved by adding 15 wt% of EG to the PCMs. The sample shows a leakage of paraffin wax below 10%, retaining a melting enthalpy of PW within PCMs of 54.8 J/g, a thermal conductivity of 1.64 W/mK and the lowest photooxidation, characterized by an increase in the concentration of carbonyl groups from all investigated materials after artificial aging. Furthermore, PCMs mixed with EG exhibited good mechanical properties, even after 100 days of exposure to artificial aging. Finally, this work demonstrates a justification for the use of recycled plastics in the formation of PCMs.
Open AccessRecycled Polyethylene/Paraffin Wax/Expanded Graphite Based Heat Absorbers for Thermal Energy Storage: An Artificial Aging Study
An artificial aging study of novel heat absorbers based on phase change materials (PCMs) prepared from recycled high-density polyethylene (HDPE), paraffin wax (PW), and expanded graphite (EG) was investigated. The optimal composition of PCMs contained 40 wt% HDPE, whereas the paraffin wax content ranged from 40 to 60 wt% and the expanded graphite content ranged from 5 to 15 wt%. PCMs were artificially aged through exposure to UV irradiation, enhanced temperature, and humidity. It was clearly demonstrated that the addition of EG to PCMs led to the suppression of PW leakage and improved the photooxidation stability of the PCMs during the aging process. The best performance was achieved by adding 15 wt% of EG to the PCMs. The sample shows a leakage of paraffin wax below 10%, retaining a melting enthalpy of PW within PCMs of 54.8 J/g, a thermal conductivity of 1.64 W/mK and the lowest photooxidation, characterized by an increase in the concentration of carbonyl groups from all investigated materials after artificial aging. Furthermore, PCMs mixed with EG exhibited good mechanical properties, even after 100 days of exposure to artificial aging. Finally, this work demonstrates a justification for the use of recycled plastics in the formation of PCMs.
- Open Access
Modification of Polyethylene by RF Plasma in Different/Mixture Gases
Herein, low-density polyethylene (LDPE) films were treated using radio-frequency plasma discharge in the presence of air, nitrogen, oxygen, argon, and their mixtures to introduce new chemical functionalities. The surface properties of treated LDPE were qualitatively and quantitatively characterized using various analytical and microscopic techniques. It was found that the optimum plasma treatment for LDPE occurs in the presence of air plasma at an exposure time of 120 s and 80 W of nominal power. The plasma formed layer had tendency to increasing thickness with increasing treatment time up to 60 s using air and oxygen and even more with inert gases. An aging study of plasma-treated LDPE samples stored in ambient air or water medium revealed the partial hydrophobic recovery.
Open AccessModification of Polyethylene by RF Plasma in Different/Mixture Gases
Herein, low-density polyethylene (LDPE) films were treated using radio-frequency plasma discharge in the presence of air, nitrogen, oxygen, argon, and their mixtures to introduce new chemical functionalities. The surface properties of treated LDPE were qualitatively and quantitatively characterized using various analytical and microscopic techniques. It was found that the optimum plasma treatment for LDPE occurs in the presence of air plasma at an exposure time of 120 s and 80 W of nominal power. The plasma formed layer had tendency to increasing thickness with increasing treatment time up to 60 s using air and oxygen and even more with inert gases. An aging study of plasma-treated LDPE samples stored in ambient air or water medium revealed the partial hydrophobic recovery.