Antonio Baldanza
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Antonio Baldanza has a total of 30 co-authors. Here are the top co-authors by number of shared publications:
- Giuseppe Mensitieri
Department of Chemical, Materials and Production Engineering, University of Naples Federico II, Piazzale Tecchio 80, 80125 Naples, Italy
11 shared publications - Giuseppe Scherillo
Department of Chemical, Materials and Production Engineering, University of Naples Federico II, Piazzale Tecchio 80, 80125 Naples, Italy
10 shared publications - Cosimo Brondi
Dipartimento di Ingegneria e Scienze, Facoltà di Scienze Tecnologiche e dell’Innovazione
5 shared publications - Pellegrino Musto
Institute for Polymers, Composites and Biomaterials, National Research Council of Italy, Via Campi Flegrei 34, 80078 Pozzuoli, Italy
4 shared publications - Valerio Loianno
University of Naples Federico II P.le V. Tecchio 80
4 shared publications - Andrea Correa
Department of Chemical Science, University of Naples Federico II, Via Cintia 21, 80126 Napoli, Italy
2 shared publications
Latest Publications
- 6 February 2026
- Published by American Chemical Society (ACS) in Macromolecules
- Vol. 59 (4) , 1833-1846
Methanol Sorption in Poly(ether imide): Molecular Insights from a Multiscale Study Combining Experiments, Theory, and Simulations
- 6 February 2026
- Published by American Chemical Society (ACS) in Macromolecules
- Vol. 59 (4) , 1833-1846
Methanol Sorption in Poly(ether imide): Molecular Insights from a Multiscale Study Combining Experiments, Theory, and Simulations
- Open Access
Sorption and mass transport of water in polyimides: quantifying first- and second-shell and their dynamics
- Open Access
Sorption of CO2, CH4 and Their Mixtures in Amorphous Poly(2,6-dimethyl-1,4-phenylene)oxide (PPO)
Sorption of pure CO2 and CH4 and CO2/CH4 binary gas mixtures in amorphous glassy Poly(2,6-dimethyl-1,4-phenylene) oxide (PPO) at 35 °C up to 1000 Torr was investigated. Sorption experiments were carried out using an approach that combines barometry with FTIR spectroscopy in the transmission mode to quantify the sorption of pure and mixed gases in polymers. The pressure range was chosen to prevent any variation of the glassy polymer density. The solubility within the polymer of the CO2 present in the gaseous binary mixtures was practically coincident with the solubility of pure gaseous CO2, up to a total pressure of the gaseous mixtures equal to 1000 Torr and for CO2 mole fractions of ~0.5 mol mol−1 and ~0.3 mol mol−1. The Non-Equilibrium Thermodynamics for Glassy Polymers (NET-GP) modelling approach has been applied to the Non-Random Hydrogen Bonding (NRHB) lattice fluid model to fit the solubility data of pure gases. We have assumed here that no specific interactions were occurring between the matrix and the absorbed gas. The same thermodynamic approach has been then used to predict the solubility of CO2/CH4 mixed gases in PPO, resulting in a deviation lower than 9.5% from the experimental results for CO2 solubility.
Open AccessSorption of CO2, CH4 and Their Mixtures in Amorphous Poly(2,6-dimethyl-1,4-phenylene)oxide (PPO)
Sorption of pure CO2 and CH4 and CO2/CH4 binary gas mixtures in amorphous glassy Poly(2,6-dimethyl-1,4-phenylene) oxide (PPO) at 35 °C up to 1000 Torr was investigated. Sorption experiments were carried out using an approach that combines barometry with FTIR spectroscopy in the transmission mode to quantify the sorption of pure and mixed gases in polymers. The pressure range was chosen to prevent any variation of the glassy polymer density. The solubility within the polymer of the CO2 present in the gaseous binary mixtures was practically coincident with the solubility of pure gaseous CO2, up to a total pressure of the gaseous mixtures equal to 1000 Torr and for CO2 mole fractions of ~0.5 mol mol−1 and ~0.3 mol mol−1. The Non-Equilibrium Thermodynamics for Glassy Polymers (NET-GP) modelling approach has been applied to the Non-Random Hydrogen Bonding (NRHB) lattice fluid model to fit the solubility data of pure gases. We have assumed here that no specific interactions were occurring between the matrix and the absorbed gas. The same thermodynamic approach has been then used to predict the solubility of CO2/CH4 mixed gases in PPO, resulting in a deviation lower than 9.5% from the experimental results for CO2 solubility.
- Open Access
- 16 January 2023
- Published by MDPI AG in Preprints.org
Sorption of CO2, CH4 and their mixtures in Amorphous Poly(2,6-dimethyl-1,4-phenylene)oxide (PPO)
Sorption of pure CO2 and CH4 and CO2/CH4 binary gas mixtures in amorphous glassy Poly(2,6-dimethyl-1,4-phenylene) oxide (PPO) at 35°C up to 1000 Torr is investigated. Sorption experiments were carried out using an approach that combines barometry with FTIR spectroscopy in the transmission mode to quantify the sorption of pure and mixed gases in polymers. The pressure range is chosen to prevent any variation of the glassy polymer density. The solubility within the polymer of the CO2 present in the gaseous binary mixtures is practically coincident with the solubility of pure gaseous CO2, up to a total pressure of the gaseous mixtures equal to 1000 Torr and for CO2 mole fraction of ~0.5 mol mol-1 and ~0.3 mol mol-1. The Non-Equilibrium Thermodynamics for Glassy Polymers (NET-GP) modelling approach has been applied to the Non-Random Hydrogen Bonding (NRHB) lattice fluid model to fit the solubility data of pure gases. We have assumed here that no specific interactions are occurring between the matrix and the absorbed gas. The same thermodynamic approach has been then used to predict the solubility of CO2/CH4 mixed gases in PPO resulting in a deviation lower than 9.5% from the experimental results for CO2 solubility.
- 16 January 2023
- Published by MDPI AG in Preprints.org
Open AccessSorption of CO2, CH4 and their mixtures in Amorphous Poly(2,6-dimethyl-1,4-phenylene)oxide (PPO)
Sorption of pure CO2 and CH4 and CO2/CH4 binary gas mixtures in amorphous glassy Poly(2,6-dimethyl-1,4-phenylene) oxide (PPO) at 35°C up to 1000 Torr is investigated. Sorption experiments were carried out using an approach that combines barometry with FTIR spectroscopy in the transmission mode to quantify the sorption of pure and mixed gases in polymers. The pressure range is chosen to prevent any variation of the glassy polymer density. The solubility within the polymer of the CO2 present in the gaseous binary mixtures is practically coincident with the solubility of pure gaseous CO2, up to a total pressure of the gaseous mixtures equal to 1000 Torr and for CO2 mole fraction of ~0.5 mol mol-1 and ~0.3 mol mol-1. The Non-Equilibrium Thermodynamics for Glassy Polymers (NET-GP) modelling approach has been applied to the Non-Random Hydrogen Bonding (NRHB) lattice fluid model to fit the solubility data of pure gases. We have assumed here that no specific interactions are occurring between the matrix and the absorbed gas. The same thermodynamic approach has been then used to predict the solubility of CO2/CH4 mixed gases in PPO resulting in a deviation lower than 9.5% from the experimental results for CO2 solubility.
- Open Access
- 11 December 2022
- Published by Wiley in Macromolecular Materials and Engineering
- Vol. 308 (3)
Carbon Nanotubes Networking in Styrene‐Butadiene Rubber: A Dynamic Mechanical and Dielectric Spectroscopy Study
The study of the reinforcement network in elastomer compounds is one of the most relevant issues for the application of these materials because their properties are strongly dependent on the obtained morphology. To this regard, the viscoelastic and dielectric behavior of vulcanized styrene butadiene rubber (SBR) reinforced with different amounts of carbon nanotubes (CNT) have been investigated and compared with the vulcanized unfilled SBR and the vulcanized SBR samples reinforced with a conventional amount of carbon black (40 phr). Differential scanning calorimetry (DSC) measurements have been carried out to highlight possible differences of the glass transition temperatures for all the reinforced compounds. The percolation threshold value of the nanocomposite samples has been estimated by dielectric analysis. Finally, dynamic mechanical analysis (DMA) measurements have been performed in tensile mode in the temperature range of −60 to 80 °C to obtain bothE′ andE′′. From these experimental data, the master curve for each sample has been estimated by using the time–temperature superposition principle in combination with the vertical shift approach. From the analysis of this latter, the activation energy, associated to the thermal movement of the reinforcement network, has been calculated to better elucidate the reinforcement mechanism in the nanocomposites.
- 11 December 2022
- Published by Wiley in Macromolecular Materials and Engineering
- Vol. 308 (3)
Open AccessCarbon Nanotubes Networking in Styrene‐Butadiene Rubber: A Dynamic Mechanical and Dielectric Spectroscopy Study
The study of the reinforcement network in elastomer compounds is one of the most relevant issues for the application of these materials because their properties are strongly dependent on the obtained morphology. To this regard, the viscoelastic and dielectric behavior of vulcanized styrene butadiene rubber (SBR) reinforced with different amounts of carbon nanotubes (CNT) have been investigated and compared with the vulcanized unfilled SBR and the vulcanized SBR samples reinforced with a conventional amount of carbon black (40 phr). Differential scanning calorimetry (DSC) measurements have been carried out to highlight possible differences of the glass transition temperatures for all the reinforced compounds. The percolation threshold value of the nanocomposite samples has been estimated by dielectric analysis. Finally, dynamic mechanical analysis (DMA) measurements have been performed in tensile mode in the temperature range of −60 to 80 °C to obtain bothE′ andE′′. From these experimental data, the master curve for each sample has been estimated by using the time–temperature superposition principle in combination with the vertical shift approach. From the analysis of this latter, the activation energy, associated to the thermal movement of the reinforcement network, has been calculated to better elucidate the reinforcement mechanism in the nanocomposites.
- 21 November 2022
- Published by The Royal Society in Philosophical Transactions of the Royal Society A: Mathematical, Physical and Engineering Sciences
- Vol. 381 (2240) , 20210216
Modelling changes in glass transition temperature in polymer matrices exposed to low molecular weight penetrants
Polymer matrices, when placed in contact with a fluid phase made of low molecular weight compounds, undergo a depression of their glass transition temperature ( T g ) determined by the absorption of these compounds and the associated plasticization phenomena. Frequently, this effect is coupled with the mechanical action of the compressive stress exerted by the pressure of the fluid phase that, in contrast, promotes an increase in the T g . This issue is relevant for technological and structural applications of composites with high-performance glassy polymer matrices, due to their significant impact on mechanical properties. We propose an approach to model and predict rubbery-glassy states maps of polymer–penetrant mixtures as a function of pressure and temperature based on the Gibbs–Di Marzio criterion. This criterion establishes that a ‘thermodynamic’ glass transition does occur when the configurational entropy of the system vanishes. Although questioned and criticized, this criterion constitutes a good practical approach to analyse changes of T g and, in some way, reflects the idea of an ‘entropy catastrophe’ occurring at the glass transition. Several polymer–penetrant systems have been analysed modelling configurational entropy by means of the Non-Random Hydrogen Bond lattice fluid theory, able to cope with possible non-random mixing and occurrence of strong interactions. This article is part of the theme issue 'Ageing and durability of composite materials'.
- 21 November 2022
- Published by The Royal Society in Philosophical Transactions of the Royal Society A: Mathematical, Physical and Engineering Sciences
- Vol. 381 (2240) , 20210216
Modelling changes in glass transition temperature in polymer matrices exposed to low molecular weight penetrants
Polymer matrices, when placed in contact with a fluid phase made of low molecular weight compounds, undergo a depression of their glass transition temperature ( T g ) determined by the absorption of these compounds and the associated plasticization phenomena. Frequently, this effect is coupled with the mechanical action of the compressive stress exerted by the pressure of the fluid phase that, in contrast, promotes an increase in the T g . This issue is relevant for technological and structural applications of composites with high-performance glassy polymer matrices, due to their significant impact on mechanical properties. We propose an approach to model and predict rubbery-glassy states maps of polymer–penetrant mixtures as a function of pressure and temperature based on the Gibbs–Di Marzio criterion. This criterion establishes that a ‘thermodynamic’ glass transition does occur when the configurational entropy of the system vanishes. Although questioned and criticized, this criterion constitutes a good practical approach to analyse changes of T g and, in some way, reflects the idea of an ‘entropy catastrophe’ occurring at the glass transition. Several polymer–penetrant systems have been analysed modelling configurational entropy by means of the Non-Random Hydrogen Bond lattice fluid theory, able to cope with possible non-random mixing and occurrence of strong interactions. This article is part of the theme issue 'Ageing and durability of composite materials'.
- Open Access
- 20 August 2022
- Published by MDPI AG in International Journal of Molecular Sciences
- Vol. 23 (16) , 9406
Survey on Adsorption of Low Molecular Weight Compounds in Cu-BTC Metal–Organic Framework: Experimental Results and Thermodynamic Modeling
This contribution aims at providing a critical overview of experimental results for the sorption of low molecular weight compounds in the Cu-BTC Metal–Organic Framework (MOF) and of their interpretation using available and new, specifically developed, theoretical approaches. First, a literature review of experimental results for the sorption of gases and vapors is presented, with particular focus on the results obtained from vibrational spectroscopy techniques. Then, an overview of theoretical models available in the literature is presented starting from semiempirical theoretical approaches suitable to interpret the adsorption thermodynamics of gases and vapors in Cu-BTC. A more detailed description is provided of a recently proposed Lattice Fluid approach, the Rigid Adsorbent Lattice Fluid (RALF) model. In addition, to deal with the cases where specific self- and cross-interactions (e.g., H-bonding, Lewis acid/Lewis base interactions) play a role, a modification of the RALF model, i.e., the RALFHB model, is introduced here for the first time. An extension of both RALF and RALFHB is also presented to cope with the cases in which the heterogeneity of the rigid adsorbent displaying a different kind of adsorbent cages is of relevance, as it occurs for the adsorption of some low molecular weight substances in Cu-BTC MOF.
- 20 August 2022
- Published by MDPI AG in International Journal of Molecular Sciences
- Vol. 23 (16) , 9406
Open AccessSurvey on Adsorption of Low Molecular Weight Compounds in Cu-BTC Metal–Organic Framework: Experimental Results and Thermodynamic Modeling
This contribution aims at providing a critical overview of experimental results for the sorption of low molecular weight compounds in the Cu-BTC Metal–Organic Framework (MOF) and of their interpretation using available and new, specifically developed, theoretical approaches. First, a literature review of experimental results for the sorption of gases and vapors is presented, with particular focus on the results obtained from vibrational spectroscopy techniques. Then, an overview of theoretical models available in the literature is presented starting from semiempirical theoretical approaches suitable to interpret the adsorption thermodynamics of gases and vapors in Cu-BTC. A more detailed description is provided of a recently proposed Lattice Fluid approach, the Rigid Adsorbent Lattice Fluid (RALF) model. In addition, to deal with the cases where specific self- and cross-interactions (e.g., H-bonding, Lewis acid/Lewis base interactions) play a role, a modification of the RALF model, i.e., the RALFHB model, is introduced here for the first time. An extension of both RALF and RALFHB is also presented to cope with the cases in which the heterogeneity of the rigid adsorbent displaying a different kind of adsorbent cages is of relevance, as it occurs for the adsorption of some low molecular weight substances in Cu-BTC MOF.